Common Plumbing Processes PDF
Document Details
Uploaded by AdvancedCourage8795
Oaklands College
Tags
Summary
This PowerPoint presentation details various plumbing processes, including jointing common plumbing materials, different types of fittings, and potential hazards. It covers threaded, compression, push-fit, and press-fit connections.
Full Transcript
PowerPoint 2 Joint common plumbing materials LESSON INTENT Learners will be able to describe and identify the following processes: Jointing Common Plumbing Materials LCS fittings Threaded Compression...
PowerPoint 2 Joint common plumbing materials LESSON INTENT Learners will be able to describe and identify the following processes: Jointing Common Plumbing Materials LCS fittings Threaded Compression Unions Flanges Plastic fittings Push fit Compression Solvent Fusion MDPE Preparing tubes and fittings for jointing Demonstrating procedures for jointing tubes Fittings: Elbows Tees Couplings Reducers End caps End feed Solder ring Push fit Compression Press fit City and Guilds 6035 Level 2 Unit 204 True Or False 1. Do Compression fitting have olives in ? YES 2. Do End Feed fitting have a solder ring ? 3. Can I use solder with Push Fit Fitting ? NO 4. Do Press Fit have an O Rings ? NO YES End feed fitting Joint is cleaned inside Pipe cleaned on outside Flux added Solder needs to be added when fitting is heated Lead-free solder must be used on hot and cold water systems Allowed to cool Joint wiped clean with cloth Use once only Solder Lead solder: 70% lead + 30% tin These types of solder can only be used on non-potable water systems – central heating or gas pipes. Lead-free solder: 99% tin + 1% copper (lead free). Flux Active fluxes are acid based and the cleaning of pipes is not necessary, but must be cleaned off after soldering. Non-active fluxes are paraffin based and the cleaning of pipes must always be carried out. Keep the surface clean Prevent oxidisation Help the solder flow Solder ring fittings Joint is cleaned inside Pipe cleaned on outside Flux added Solder is in integral ring Joint is heated to allow solder to flow Allowed to cool Joint wiped clean with cloth Use once only Push fit fittings These can be used on pressure plastic pipe or copper pipe Pipe end must be cut square and burr free Sleeve or insert used to support plastic pipe O ring creates watertight seal Grab ring retains pipe Silicon gel can be used to aid insertion (manufacturers supply fittings already lubricated) A key or release tool may have to be used to remove fitting Reusable and re-positional Push fit fittings These components are produced by many manufacturers and come in different finishes. Compression fittings These come in two styles: Type A: Non-manipulative fittings: require nothing more than the piece of pipe to be cut square and the burrs removed. The fitting is assembled with an olive, and tightened using an adjustable spanner. Suitable for half hard copper and plastic pressure pipe. Type B Manipulative fittings: require the end of the pipe to be manipulated using a swaging tool. They are much stronger than the type A fittings and cannot be pulled apart. Mostly used for high pressure and below ground pipe work. Brass fittings Brass is an alloy – copper and zinc. Brass fittings can suffer from dezincification. This shows itself in a white power (zinc oxide) coating on the outside of a fitting. It leaves the fitting very brittle. Modern fittings are marked CZ or DZR which means they are dezincification resistant. Press fit fittings These rely on an O ring to create the watertight seal. They are pushed into position after marking the component depth. Once in place, they are clamped into position using a mechanical clamping tool. When lead pipe is found in a property, the customer should always be advised that it should be removed. Sometimes it is necessary to connect either copper or plastic pipe to an existing lead pipe. This needs to be done carefully and by using a proprietary fitting (eg leadlock). This allows old lead pipes to be connected to copper pipes safely. The old wiped joint is not allowed to be used. LCS fittings Threaded: using BSPT threads, along with PTFE or hemp and paste, to create the watertight seal. Compression: these use a tapered rubber seal to create the watertight seal. Unions: these are commonly supplied with either a flat face or conical face to create the watertight seal. Flanges: these come in flat face and use either a rubber or fibre gasket to create a watertight seal. Tap Connectors The function of a tap connector is to connect the supply pipework to the underside of a tap or float operated valve. To create a watertight seal, a fibre washer must be used. Flexible Connectors The function of flexible connectors is to make it easy to connect two positions. This could be between a supply pipe and a tap or an appliance and a waste pipe. Tap connectors are usually 300mm long and can have an integral isolator. Manifolds The function of a manifold is to allow one pipe to be divided into several others, like a microbore or underfloor heating manifold. Alternatively, it could be the other way around: in the case of a waste manifold, several waste pipes enter the soil stack. Tank Connectors The function of a tank connector is to allow a supply point from a cistern, like the cold distribution from the cold water storage cistern. They rely on rubber and neoprene washers to create a watertight seal. Plastic push fit fittings Plastic to copper as well as plastic to plastic. Hot water, cold water and central heating push fit fittings have the retention rings but soil and waste, as shown, only have the O ring seal. Expansion allowance is always required. Make sure the O rings are in place and not damaged. Silicon grease is useful to allow the joint to be made after the burrs have been removed. Plastic compression fittings Sometimes referred to as Mechanical fittings. Plastic to copper or plastic to plastic. The seals or O rings must be in place and not damaged when the pipe is pushed into place. All burrs must be removed. The important support ring must also go behind the seal. Generally used on waste fittings. Plastic solvent weld fittings Used on ABS and uPVC waste or soil pipes. The surface is cleaned, and solvent cement is applied to both internal and external components. They are pushed together and the material chemically melts together. The joint sets within minutes. Plastic MDPE fittings These can be compression to allow plastic-to-plastic connections. They can be a combination of plastic compression and copper push fit, or plastic compression to screw thread LCS. They can be push fit only for MDPE. MDPE can be fusion welded. Used on copper Flux: active and passive. Use to aid the flow of solder, stop oxidation and keep the surface clean. PTFE tape and liquid: use on compression fittings over the olives. (Polytetraflouroethylene). Sealing paste: small amounts of paste are used on olive. Used on low carbon steel PTFE tape and string: use on the threads of the pipe. (polytetraflouroethylene). Hemp and paste: used on the threads of the pipe without blocking the pipe. Gaskets: either rubber or fibre gaskets are used on flange faced joints. Used on plastics Solvent weld: used on waste and soil pipes. Fusion weld: used on underground utility pipework. Rubber seals: used on waste and soil pipes (silicon). O Rings: used on push fit, waste and soil pipes (silicon). Hazards Burns to person Burns to property Fires Explosions Oxidation from flux Pitting Fumes from soldering Fumes from solvent welding Hazards All metallic pipes need to be earthed: Equipotential bonding Supplementary bonding Temporary continuity bonding All hidden plastic pipework needs to have metallic tape attached so it can be traced behind walls. Quality assurance All components fitted in any installation should be: WRAS approved British Standard kite mark BBA approved BRE Building Research Establishment offer advice and information IOPHE Institute of plumbing and heating engineers is the plumbing lead body, offering guidance CHECK YOUR KNOWLEDGE WITH THESE QUESTIONS. 1. What is this fitting called? 2. What is this fitting called? 3. What is this fitting called 4. What is active flux 5. What is solvent wield used on? TRAFFIC LIGHT IT: WHERE IS YOUR LEARNING AT? Red = I have not really understood the content we have studied today (write down 2 questions that you need help with) Amber = I have understood the content on Effective Questionning (write down 1 one question you need to clarify) Green = I have understood all the content (write down one example from what we have studied)