74 Questions
What should you do if the gap between the Rubber Axle Stop and spring is less than 1/16"?
Submit a defect report
What is the acceptable range for the gap between the Rubber Axle Stop and spring?
1/16" to 1/2"
What should you do if the gap between the Rubber Axle Stop and spring is greater than 1/2"?
Place the vehicle out of service
What is the purpose of the defect report in this context?
To notify of a potential safety issue
What is the consequence of not submitting a defect report?
The issue may not be addressed in a timely manner
What should you do if you identify a defect during the daily inspection?
Submit a defect report
Who should be contacted if the gap between the Rubber Axle Stop and spring is greater than 1/2"?
CMF
What is the purpose of the daily inspection?
To identify potential safety issues
Where can you access serious faults or messages?
Home screen
What is the purpose of the 'Do Not Move Truck' feature?
To identify open doors or other warnings
Where can you access the 'Diagnostics' feature?
Menu screen
What does the 'Diagnostics' feature show?
Status of various systems on the vehicle
What happens to the rear camera screen when the transmission is in Reverse?
It displays automatically
How do you manually activate the rear camera screen?
Press down arrow
Where is the rear camera located?
Above the rear compartment
What happens when the transmission is not in Reverse?
You need to press down arrow to display the rear camera screen
What should be done if cracks are found in the metal of the S-Buffer?
Submit a defect report
What should be done if the Rubber Axle Stop is missing or torn?
Place the truck out of service
What should be inspected daily on the S-Buffer Assembly?
All of the above
What should be done if loose hardware is found on the S-Buffer Assembly?
Submit a defect report
What is the purpose of the S-buffers in the front suspension?
To reduce undesirable steering reaction during emergency braking
What should be done if the Rubber Axle Stop has surface cracks?
Submit a defect report
What is the purpose of daily inspections on the S-Buffer Assembly?
To ensure the safety of the vehicle and its occupants
What should be done if the S-Buffer Assembly has signs of failure or tearing?
Submit a defect report
What type of fluid is used in the exhaust system of the 2018 Pierce Enforcer Engine?
Diesel exhaust fluid
What is the purpose of the regeneration switches in the 2018 Pierce Enforcer Engine?
To prevent active regeneration in undesirable locations
What is the diesel particulate filter used for in the 2018 Pierce Enforcer Engine?
To filter the diesel exhaust
What happens during active regeneration in the 2018 Pierce Enforcer Engine?
The system enters a regeneration mode
Why is it important to verify clearances and secure loose items before operating the 2018 Pierce Enforcer Engine?
To avoid damaging the cab or arm
What should you do before adding fluid to the reservoirs in the 2018 Pierce Enforcer Engine?
Verify the type of fluid required
Where is the locking safety arm located in the 2018 Pierce Enforcer Engine?
On the driver’s side lift cylinder
What should you do when stowing the handheld actuator?
Verify the arm lands in the pocket
What is the purpose of the handheld actuator in the 2018 Pierce Enforcer Engine?
To engage the raise/lower function
What is the purpose of the toggle switch marked 'activate'?
To serve as an alternative to the handheld actuator
What is the diameter of the exhaust outlet?
6"
What is the maximum diameter of exhaust outlets that PlymoVent boots can accept?
6.25"
Why may the PlymoVent boot need to be manually disengaged from the exhaust outlet?
Because the rubber molds to the larger tailpipe over time
What is the importance of checking the mirror when exiting the station?
To ensure the hose disengages from the exhaust outlet
Why are slow and steady departures from the bay necessary?
To allow the rubber to mold to the larger tailpipe
What is the location of the diesel fuel fill on the 2018 Pierce Enforcer Engine?
On the driver’s side, co-located with the DEF fill
What is the color of the diesel fuel cap on the 2018 Pierce Enforcer Engine?
Silver
What is the capacity of the diesel fuel tank on the 2018 Pierce Enforcer Engine?
65 gallons
What prevents the SCBA from becoming a projectile in the event of a collision?
The blue latching mechanism
How do you release the SCBA from its holder?
By using a slow and smooth motion
What is the purpose of the loops on the SCBA-equipped seats?
To stow SCBA straps
What is the type of pump used in the 2018 Pierce Enforcer Engine?
Hale 1500gpm single-stage pump
What is the indicator of a successful pump shift in the cab?
All of the above
What is the purpose of the Trident air primer?
To prime the pump
What is the capacity of the water tank in the 2018 Pierce Enforcer Engine?
750 gallon
What is the type of foam tank used in the 2018 Pierce Enforcer Engine?
Class A foam tank
What is the minimum speed required for DPF regeneration to occur during travel?
5 mph
What is the purpose of the DPF Regen switch while parked?
To manually initiate a parked regeneration
What is required for DPF regeneration to occur during pumping operations?
NO engine speed variations
What is the recommended clearance from the exhaust outlet during DPF regeneration?
5 feet
Why may DPF regeneration need to be inhibited during pumping operations?
Due to clearances to the exhaust outlet not being available
What is NOT a recommended location for DPF regeneration?
Inside a building
What is the primary purpose of the regeneration switches in the 2018 Pierce Enforcer Engine?
To initiate active regeneration
What happens during active regeneration in the 2018 Pierce Enforcer Engine?
The exhaust temperature is increased to burn off soot
Why is it important to verify clearances and secure loose items before operating the 2018 Pierce Enforcer Engine?
To reduce the risk of injury or accident
What is the purpose of the diesel particulate filter in the 2018 Pierce Enforcer Engine?
To reduce emissions and particulate matter
What is the consequence of not initiating active regeneration in the 2018 Pierce Enforcer Engine?
DPF clogging and potential engine damage
Where is the regeneration switch located in the 2018 Pierce Enforcer Engine?
Near the diesel particulate filter
What is the recommended practice before adding fluid to the reservoirs in the 2018 Pierce Enforcer Engine?
Check the fluid type and level
What is the primary function of the locking safety arm in the 2018 Pierce Enforcer Engine?
To prevent the cab from lowering
What is the purpose of the handheld actuator in the 2018 Pierce Enforcer Engine?
To activate the cab raise/lower function
What is the recommended storage procedure for the handheld actuator?
Store it in a designated pocket ahead of the wheel well
Where is the diesel exhaust fluid (DEF) fill located on the 2018 Pierce Enforcer Engine?
Co-located with diesel fuel fill on the driver's side
What is the capacity of the diesel fuel tank on the 2018 Pierce Enforcer Engine?
65 gallons
What is the diameter of the exhaust outlet on the 2018 Pierce Enforcer Engine?
6 inches
Why may the PlymoVent boot need to be manually disengaged from the exhaust outlet?
Because of the tight fit
What is the importance of checking the mirror when exiting the station?
To ensure the hose disengages from the exhaust
What is the color of the diesel fuel cap on the 2018 Pierce Enforcer Engine?
Silver
Where is the diesel fuel fill located on the 2018 Pierce Enforcer Engine?
On both sides of the apparatus at the rear wheel well
What is the capacity of the DEF tank on the 2018 Pierce Enforcer Engine?
4.5 gallons
Study Notes
Monthly Inspection
- Park the loaded vehicle on flat level ground with wheels pointed straight and ensure parking brake is applied and wheels are chocked.
- Inspect the gap between the Rubber Axle Stop and spring, which should be between 1/16” and 1/2”. If outside of this range, drive cautiously and re-measure.
- If the gap is > 1/2”, place the vehicle out of service and contact CMF. If < 1/16” or the Rubber Axle Stop is touching, submit a defect report.
Brake Pads
- Bendix ADB22X Disc brake pads must be replaced at 11mm (approximately 7/16”).
- Meritor DiscPlus EX225 Disc brake pads must be replaced at 3mm (approximately 1/8”).
Jumper Studs and Glad Hands
- Jumper studs are accessible below the driver's side cab door when the cab is nested.
- Glad hands are located below the front bumper to assist with towing.
OnSpot Automatic Snow Chains
- OnSpot automatic snow chains are on the rear axle.
- Switch is located on the dashboard to the left of the steering wheel.
- The chains have a 5-second delay before activation.
Axles and Brakes
- 20,000lb front axle and 27,000lb rear axle.
- Parking brake locks up all wheels and has a 2nd actuator located on the officer's side dashboard.
- Anti-lock disc air brakes on both front and rear axles.
- 18.7cfm air compressor and 12v auxiliary air compressor behind the driver's seat.
Air System
- Heated air dryer on the wet tank.
- Stainless steel air storage tanks.
- Air tank drain actuators located on the driver's side beside the wheel chock mount.
Front Suspension
- When the vehicle is under stress, front springs flatten and then assume an "S" shape.
- "S-buffers" in the front suspension stiffen the springs when compressed to reduce undesirable steering reaction during emergency braking.
Daily Inspection
- Inspect for loose hardware of the S-Buffer Assembly.
- Inspect welds and surrounding metal of the S-Buffer Assembly for cracks.
- Look for signs of failure or tearing of the Rubber Axle Stop.
- If cracks are found, submit a defect report.
- If the Rubber Axle Stop is damaged, place the truck out of service and replace it.
Notifications
- Notifications are accessible from the Menu screen.
- Serious faults or messages will also appear on the Home screen.
HVAC and Other Features
- HVAC controls are accessible from the Menu screen and are the same as the dashboard controls.
- Do Not Move Truck feature is accessible from the Menu screen and enables specific identification of open doors or other warnings.
- Timer feature is accessible from the Menu screen.
- Diagnostics feature is accessible from the Menu screen and shows the status of various systems on the vehicle.
- Rear Camera Screen is accessible from the Menu screen and defaults to this screen automatically when the transmission is in Reverse.
Handheld Cab Tilt Actuator
- Serves single function to activate the selected function
- Can be replaced by the toggle switch marked "activate" if unavailable
Locking Safety Arm
- Located on driver's side lift cylinder
- Stowed atop the frame rail beside the motor
- Metal becomes HOT as motor compartment heats up – use gloves to handle
- Held down by a rubber stopper during storage, may require effort to dislodge from storage
Safety Precautions
- Always verify clearances, secure loose items, and engage the safety arm
- Watch the clearance of the mirror
Engine Components
- Air compressor
- Alternator
- Starter Motor
- Power steering fluid reservoir
- Motor oil fill and dipstick
- Transmission dipstick and fill
- Turbo
Vehicle Features
- Equipped with diesel exhaust fluid and a diesel particulate filter
- Regeneration switches and DPF and exhaust temp warnings
- Active regeneration mode can be prevented by switching off when regen may engage in an undesirable location
Fuel and Fluid
- Diesel fuel: fills on both sides of the apparatus at the rear wheel well, 65 gallon capacity
- Diesel Exhaust Fluid (DEF): fills on driver's side, 4.5 gallon tank, level displayed on dashboard gauge panel and in Command Zone display
- DEF cap is light blue and requires opening two doors
Exhaust Outlet
- 6" diameter, Crimson is 5"
- PlymoVent boots will accept up to 6 ¼" exhaust outlets
SCBA
- No straps or levers to restrain or release the SCBA
- Blue latching mechanism holds the SCBA in place during transit
- To release the SCBA, a smooth motion is required
- Adjustment knob on top of the bracket to adjust tank fit
SCBA Straps
- Each SCBA-equipped seat has loops to stow SCBA straps
- Secured by magnets (look like buttons)
Pump Features
- Hale 1500gpm single stage Qmax pump
- Hale Total Pressure Master (TPM) system
- Trident air primer
- Class 1 SmartFOAM proportioner with FoamLogix
- 6.5 pump
- 750 gallon water tank
- 50 gallon class A foam tank
- No CAFS, No integral Class B foam tank, No Autofill
Pump Shift
- In-cab signs of successful pump shift: indicator lights, Command Zone screen, speedometer rises
- Pump panel signs of successful pump shift: Pump Engaged light, 3rd panel light, pressure rise on main discharge gauge, Auto light on pump primer
DPF Regeneration
- Regeneration occurs when the operator creates correct conditions during travel or pumping operations, requiring sufficient exhaust flow and temperatures, speedometer >5mph, and no engine speed variations.
- Regeneration can also be initiated manually by activating the DPF Regen switch while parked, with the DPF lamp illuminated.
- Important: do not perform regen inside a building or while attached to an exhaust removal system, and maintain a minimum of 5 feet of clearance from the exhaust outlet.
Handheld Cab Tilt Actuator
- Serves a single function to activate the selected function.
- Plug in the handheld actuator to activate the function.
- If not available, the toggle switch marked "activate" serves the same purpose.
Safety Arm
- Located on the driver's side lift cylinder, stowed atop the frame rail beside the motor.
- Metal becomes hot when the motor compartment heats up, so use gloves to handle.
- No cables to pull or latches to operate, and held down by a rubber stopper during storage.
- Drops into a pocket ahead of the wheel well, but be sure to verify the arm lands in the pocket to avoid damage.
Engine Compartment
- Components include the turbo, air compressor, alternator, starter motor, power steering fluid reservoir, and air compressor.
Fluid Reservoirs
- Power steering fluid reservoir located nearby.
- Air compressor located nearby.
- Motor oil fill and transmission dipstick and fill located nearby.
- Power steering fluid and motor oil dipstick located nearby.
Diesel Exhaust Fluid and Diesel Particulate Filter
- Vehicle is equipped with diesel exhaust fluid and a diesel particulate filter.
- Regeneration switches, DPF and exhaust temp warnings, and diesel fuel level displayed on the dashboard gauge panel and in Command Zone display.
Diesel Fuel and Diesel Exhaust Fluid
- Diesel fuel fills on both sides of the apparatus at the rear wheel well, with a 65-gallon capacity.
- Diesel Exhaust Fluid (DEF) has a 4.5-gallon tank, fills on the driver's side, and has a light blue cap.
- DEF fluid level is displayed on the dashboard gauge panel and in Command Zone display.
Fuel Filling
- To fill, open the fuel fill access on the driver's side, then pull down the spring-loaded cover to access the DEF tank cap.
- Driver side fill is for diesel and DEF, while the officer side fill is for diesel only.
Complete daily inspection and perform physical inspection of spring for mechanical damage. Includes parking and positioning of vehicle, applying brakes, and inspecting gap between Rubber Axle Stop and spring.
Make Your Own Quizzes and Flashcards
Convert your notes into interactive study material.
Get started for free