Dairy Waste Management PDF

Module 8 Effluent treatment M-VIII. 13 Types of waste, and Waste Management in dairy industry 13.1 INTRODUCTION: All the food processing plants, including multi-product factories, produce wastes in one form or the other. The food products contain a large amount of carbohydrates, proteins, fats and...

Module 8 Effluent treatment M-VIII. 13 Types of waste, and Waste Management in dairy industry 13.1 INTRODUCTION: All the food processing plants, including multi-product factories, produce wastes in one form or the other. The food products contain a large amount of carbohydrates, proteins, fats and mineral salts. During flushing and washing operation of various process equipment, these nutrients enter the drainage and favor the growth of anaerobic and aerobic bacteria. As a result the flushed water emits obnoxious odour and can become a disposal problem as such in the municipality sewerage. 13.2 DEFINITION OF WASTE MANAGEMENT: Waste management is the collection, transport, processing, recycling or disposal, and monitoring of waste materials. 13.3 TYPES OF WASTES IN A FOOD PROCESSING PLANTS: The wastes generated in a food processing plant can be classified according to their:  Forms.  Sources  Being avoidable or unavoidable.  Value or their reuse potential. 13.3.1 Based on the forms: Wastes based on forms can be classified as:  Solid wastes,  Liquid wastes ,  Oily wastes,  Gaseous wastes/water vapors. 13.3.1.1 Solid wastes: These refer to those wastes which are obtained in solid form either as a result of processing or are generated during maintenance. Examples are: Minute particles in the exhaust air coming out of a drier, Solid ghee residue in ghee section Ash from Boiler, if solid fuel is being used, Packaging section, where considerable packaging materials may be discarded in the form of LDPE films, cartoons, bottles etc. Wastes generated by adverse events. (Explosions, fire etc.). Damaged and contaminated equipment and contaminated soil.  Types, Degree, Waste Management 13.3.1.2 Liquid wastes: These refer to those wastes which are obtained in liquid form as a result of processing, cleaning, flushing etc. The wastes resulting from processing may include un-reacted raw materials, impurities or byproducts generated in process because of operational deterioration, e.g., if the milk is not pasteurized at the right time and if it becomes sour then it will be dumped in the drain. Water used for cleaning purposes, acid, and lye as used in the CIP also comes under these wastes. 13.3.1.3 Oily wastes: These wastes results from the leakage in compressors, hydraulic machines, crankcase, and coolant leakage and motors where oil is required for lubrication. These wastes are differentiated from liquid wastes because they need a different disposal method. 13.3.1.4 Gaseous wastes/water vapors: These wastes refer to those released in the air in the form of gases or volatile vapors. The obnoxious fume from the chimney is a gaseous waste and pollutes the environment to a major degree. This chimney fuel consists of various gases like CO2 and CO. Apart from it; the refrigerant leakage from pipe lines of the compressors also comes under this category. Gaseous wastes from processing plants include the water vapors formed in a concentrating section. These vapors increase the relative humidity of the surrounding and the energy they carry with them is wastage to the plant. Steam leakage from various points decreases the life of the tees and knobs used for regulation purpose, nuts and bolts because all of these corrode with time. 13.4 WASTE MINIMISATION As per Industrial Waste Management Policy premises which are subject to works approval require waste management plans incorporating waste minimisation. Each dairy plant should therefore assess opportunities for reducing waste arising from its operations. Waste reduction measures may include:  reducing use of water  reducing use of chemicals  recycling water and chemicals  recovery and reuse of product from first reuse  reuse/reprocessing of off-spec material  recovering and reusing spilled raw materials and products.  Types, Degree, Waste Management 13.4.1 PROCESS CONTROL Dairy configuration and the products made affect the nature and concentration of dairy wastes. The amount of product lost depends on design and operational factors including:  the range of process technologies in use  the availability of adequate process monitoring, and plant and procedure alarms/interlocks  the availability of automated operation – especially automated clean-in-place (CIP) systems and procedures  the level of management and operator commitment, training and efficiency  the level of routine equipment maintenance. Most site losses come from activities associated with liquid handling and, to a lesser extent, with the discharge of air and solid waste. 13.4.1.1 Avoidable losses: Some examples of avoidable losses are:  leaking valves, pumps, pipelines or other fittings – the volume lost may not be large but the pollution load may be great  spills from overflows, malfunctions and poor handling procedures – spills usually happen over a short period but the amount and the high concentration of milk or product lost may be a significant increase in the pollution load  losses from processing and cleaning during the normal operation of plant and equipment This includes the deliberate discharge of unwanted materials such as whey, spent cleaners and diluted product not thought to be worth recovering. Liquid milk production may lead to the generation of odour, wastewater, noise and solid waste. Best practice involves processing the predominant by-products such as whey, buttermilk and skim milk, into high value products like skim milk powder (SMP), buttermilk powder (BMP), whey powder, whey protein concentrate and casein, rather than being used as low value animal feed/fertilizer or being dumped as waste. Cream and butter are viscous and fatty and stick to equipment surfaces much more strongly than liquid milk, increasing the problem of removing residues. Hot water is an effective way to remove residual butterfat from cream processing, butter making equipment and ghee making equipment but the water temperature must not be too  Types, Degree, Waste Management high (< 65°C). Accordingly, prepare a waste management plan. To initiate the process of cleaner production, a change in culture to waste minimization is required. This involves moving from pollution treatment and control to anticipation and prevention of wastes. 13.4.1.2 Surface deposits: There are certain ways to prevent the build up of surface deposits include  minimization of surface area  prevention of build-up of milk stone deposits  maintenance of butter churns  correct preparation before filling  not over-working the batch (this does not often happen with continuous butter making). To avoid spills, buttermilk collection facilities should be large enough to hold all buttermilk discharged. Buttermilk should be dried or used as animal feed and solids recovered from butter wash water also may be sold as stock feed.Suggestions for avoiding wastes during butter production, Cheese and dried milk products. Cheese generates a large volume of byproducts such as whey. 13.4.1.3 Waste reduction: Waste reduction can be achieved by  not overfilling cheese vats to stop curd loss  completely removing whey and curds from vats before rinsing  segregating all whey drained from cheese  sweeping up pressings (particles)  screening all liquid streams to collect fines. Waste reduction in evaporation and powder production can be done by operating the evaporators as following:  maintain a liquid level low enough to stop product boil-over  run to specified length – excessively long runs with higher than specified running rates lead to blocked tubes which not only produce high pollution, but are difficult and time-consuming to clean  use effluent entrainment separators to avoid carry-over of milk droplets during condensation of evaporated water  recirculate low concentration milk or other feed-stock until it reaches the required concentration  Types, Degree, Waste Management  process rinsing with 7% or more of solids before scheduled shutdowns, or evaporate them during the next run rather than discharging to the sewer  minimize air emissions by using fabric filters or wet scrubbers.