3D Printer User Manual PDF

Summary

This document is a user manual for a 3D printer, providing detailed instructions on assembly, operation, and troubleshooting. It covers various aspects of 3D printer use, from safety precautions to troubleshooting common issues.

Full Transcript

**Part-II** **Chapter 2 ( 3D Printer)** Safety Instructions =================== Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Technical Specification ======================= Printing Parameters: -------------------- Temperature Parameter --------------------- Software Parameter -----...

**Part-II** **Chapter 2 ( 3D Printer)** Safety Instructions =================== Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Technical Specification ======================= Printing Parameters: -------------------- Temperature Parameter --------------------- Software Parameter ------------------ Electrical ---------- Physical Parameter ------------------ Part List ========= ![](media/image11.jpeg) Product Overview ================ ![](media/image13.jpeg) 3. Menu Directory ============== 1. :Home menu: 2. :APPCATION menu: ![](media/image15.png) ![](media/image18.jpeg) 3. :SYSTEM menu: 4. :PRINT menu: ![](media/image20.jpeg) Assembly instructions ===================== : Components assembly steps: ---------------------------- **(Figure 1)** ![](media/image23.jpeg) ![](media/image25.jpeg) ![](media/image27.jpeg) **(Figure 6)** **Step 7**: Install the top Aluminum(AL-5) as shown in **Fig.7**. ![](media/image29.jpeg) **(Figure 8)** **(Figure 9)** : Main board wiring diagram as shown in Fig.10. ----------------------------------------------- ![](media/image31.jpeg) : Select the correct voltage mode according to your local voltage ratings(110V/220V).The switch is on the power supply which inside the base box as shown Fig.11.(Factory default is 220V) ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ :Filament installation ---------------------- **(Figure 12)** - Only insert filament into the hotend after "Preheat" it later. - It is suggested to cut off the bent tip of the filament, and rotate the filament if feels any resistance during installation. - It is important to make sure there is no tied or tangle on the reel. Leveling instructions ===================== ![](media/image34.jpeg) ![](media/image36.jpeg) - Now, as the temperature rises, please manually insert the filament through the Teflon tubing all the way into the hotend. (Refer to previous **Fig.12**) - The filament should flow through when temperature reaching to over\~180-190°C, otherwise the filament has not been inserted properly. - Customers may use tweezers to carefully remove the extruded filament at the nozzle tip before printing. There might be 3 kinds of results for the first layer of the test prints (**Fig. 17**). ![](media/image45.jpeg)![](media/image47.jpeg) Step 7: The supplementary instructions for Leveling (this step is not normally required) ---------------------------------------------------------------------------------------- 1. Adjust the 4 nuts under the platform, let the height in-between the support plate and the heat bed is a suitable distance for all the 4 corners (Suitable distance means the heat bed must be horizontal)as shown in **Fig.18**. **(Figure 18)** 2. As shown in **Fig 19**, Loosen Z adjustable nut(Refer to previous **Step 1**) by X mm if nozzle is lower than the platform (X is defined by how much the nozzle is under the platform), while Tighten it by Y mm if nozzle is too high from the platform (Y is defined by how much the nozzle is above the platform). It may need adjustment for few times. 3. On Home menu,click\"APPCATION\" \>\"LEVELING\" then home to verify the results. After this, please level the Cura Instructions ================= :Cura Installation ------------------ ![](media/image50.png)![](media/image54.png) ![](media/image62.png) : Cura settings --------------- 1. **Machine settings** ![](media/image64.jpeg) Basic and Advanced options -------------------------- ![](media/image66.png) **(Figure 23)** Plugins ------- Start/End-GCode --------------- ![](media/image68.png) **(Figure 25)** : Load 3D model into Cura ------------------------- 1. Clear the platform by clicking "File"\-\--\>"Clear platform" 2. Load 3D files onto the platform by "File"\-\--\>"Load model file...". Files with extension such as "STL", "OBJ", "DAE" and "AMF" can be loaded. :Manipulate 3D model in Cura ---------------------------- 1. Zoom in/out: scroll the mouse wheel 2. Change viewing angle: right click the model, hold on and move the mouse 3. Position change: left click on the model, hold on and drag the model to move. 4. Rotate: single left click on the model and several icons will appear at the bottom left of the window (**Fig.26**). Click the rotate button, 3 circles will surround the model. Rotate the model by moving the circle lines. - Lay flat: it is very impartant to ensure the flat portion of the model is well attached to the platform. So, please use Lay Flat option everytime after rotating the model, as it will minimize the adhesion issues during printing(**Fig.26**). - Reset: click it to return the model to the original orientation. 5. Scale: to uniformly scale the model along X/Y/Z dimensions. To disable uniform scaling, click the lock in the lower section of the scaling window. (**Fig.27**) **(Figure 27)** 6. View mode (**Fig.28**): to view the model in different ways and helps to spotting issues before print starts. Such as "Layers" mode: to view the toolpath of the print head to check if there are skipped layers or gaps. ![](media/image71.jpeg) :Save GCode in Cura ------------------- - Re-open the Gcode file again in Cura to confirm that all slices of the model have been included by check it in the "Layers view" (refer to previous **Fig.28**). - The file name should only contain English letters, underscore and space. File name contains special characters could not be recognized by the printer. ------------------------------------------------------------------------------------------------------------------------------------------------------ 3. Wire diameter: The diameter of the selected wire is 1.75mm 4. Nozzle size: Nozzle diameter is 0.4mm 5. Printing speed: 50-60mm/s is recommended, it should not be set too fast, too fast will affect the printing accuracy 6. Shell print speed: Reduce the print speed of the outermost layer to improve the flatness of the model surface Online printing Instruction =========================== 7-1. Driver installation for online printing -------------------------------------------- - Firstly, power on the machine and connect it to PC via USB cable. - CH341SER driver is copied in the SD card. "Programming software and Driver"\-\--\> "CH341SER". Right click\"CH341SER\" on your computer to install the driver as shown **Fig.30**. ![](media/image73.jpeg) 7-2. Cura settings for online printing -------------------------------------- - If the PC has been installed CH341SER driver before, then there should be a COMx in Ports of Device manager already. - Sometimes, even the driver is not installed properly, it may still show an abnormal COMx in Ports, please just ![](media/image75.jpeg) 7-3. Print online by Cura ------------------------- 1. After parameter settings, customer can print online by Cura with USB connection. Click "File"\-\--\>"Print..." as shown in **Fig.32**. 2. After click\"Print...\",it will appears the printing windows as **Fig.33**.Then the temperature would rise and it will start to print when reaching to the target temperature. Offline Printing Instruction ============================ ![](media/image78.jpeg) Change Filament Instruction =========================== - Make sure the filament passes through the filament sensor first before reaching into the extruder. - For easier feed in the filament, it is suggested to cut off the bent tip before insert. ![](media/image81.jpeg) Resume From Outage ================== ![](media/image83.jpeg) **(Figure 37)** 3. Insert the SD card,Print the just saved file (i.e."test.gcode"). The machine will automatically heating on and print. \*Note: ------- - In order to get smooth surface, use tweezers to carefully remove the excessive filament at nozzle before continuing print upon the last point. - DMSCREATE DP-X 3D printer supports resume from outage only when print offline - Due to the differences of filaments, temperature, extrusion, etc...we could not guarantee a perfect surface at the point of "Resume from outage", especially for small object. Trouble shooting ================ ![](media/image85.jpeg)Not extruding at start of print ------------------------------------------------------ 1. Extrusion is not working 2. Ensure that the nozzle temperature has been set to match the filament 3. Nozzle is too close to the heat bed 4. Nozzle clogged please try to replace it or clean it 5. Teflon tubing has been tangled, squeezed or bent 6. Filament tangled on spool 7. Not enough cooling for the hot end The first layer doesn\'t adhere on the heat bed ----------------------------------------------- 1. Print too fast at the bottom layer speed, reduce it to \~20mm/s 2. Ensure that the print platform is clean (use alcohol if necessary) 3. Check if the heat bed is proper leveled 4. Check the bed temperature matches the filament 5. Check the filament type matches the heat bed 6. Nozzle is too far to the heat bed 7. Printing model bottom area is too small 8. Open cooling for the first layer,especially for ABS 9. Add a brim or raft to the model in slicing software ![](media/image88.jpeg)Filament flowing insufficient ---------------------------------------------------- 1. Measure the diameter of filament precisely to see if it is right size 2. The Flow(%) value has been set too low in the slicing software Filament leaking or flowing too much ------------------------------------ 1. Nozzle or throat tube is tightened properly, try to fix/change it after cooling 2. Measure the diameter of filament precisely to see if it is right size 3. Check Pulse Number of extrusion motor 4. The Flow(%) value has been set too high in the slicing software ![](media/image90.jpeg)There are gaps or hollow on the top layer ---------------------------------------------------------------- 1. Insufficient number of layers for the printing model 2. Fill value has been set too low in the slicing software 3. Filament flowing insufficient Wire drawing ------------ 1. Insufficient withdrawal distance 2. Insufficient withdrawal speed 3. Printing temperature is too high 4. Poor tangential path ![](media/image93.jpeg)Printing model melting because of high printing temperature ---------------------------------------------------------------------------------- 1. Not enough cooling for the hot end 2. Printing temperature has been set too high in the slicing software 3. Printing speed is too fast Layer shifting or lost step --------------------------- 1. Print head moving too fast, slow down the print speed. 2. Check X/Y belt and the driving wheel and ensure they are properly installed. 3. Grease the rods and check all nuts and bolts remain tightened. 4. Check the main board ![](media/image96.jpeg)There are gaps between layers ---------------------------------------------------- 1. Layer thickness value has been set too high in the slicing software 2. Printing temperature is too low 3. Excessive temperature difference cause the printing model cracking(This situation is common in ABS) Grinding filament or filament wore out -------------------------------------- 1. Increase Printing Temperature 2. Reduce printing speed 3. Nozzle clogged,clean or replace it ![](media/image98.jpeg)Hot end clogged -------------------------------------- 1. After checking printing temperature,manually feed the filament to see if the filament flow out 2. Clean or replace the nozzle and nozzle throat Not extruding at the process of print ------------------------------------- 1. Filament runs out 2. Grinding filament and slipping at the gear of extrusion(Gear rotation,but no filament flow out) 3. Nozzle clogged 4. The extrusion motor driver is overheating ![](media/image100.jpeg)Filling virtual filament ------------------------------------------------ 1. Adjust the Fill value in the slicing software 2. Reduce the Fill Speed value in the slicing software 3. Modify the Fill Width value(Some slice software can be adjusted) Stripes or bulge on the surface ------------------------------- 1. Printing temperature is too high 2. Z axis is not straight 3. The setting of Slice path is not good 4. Extruding instability ![](media/image102.jpeg)Rough angle ----------------------------------- 1. Printing temperature is too high 2. Not enough Cooling for hot end Path line on the surface ------------------------ 1. Filament extruding too much 2. Uplift Z axis ![](media/image104.jpeg)Wrinkles on the surface ----------------------------------------------- 1. The quality of filament is poor,so the diameter is unstable 2. Temperature fluctuation 3. Heat bed shaking 4. Z axis is not straight or wrong installation Vibration --------- 1. Printing speed is too fast 2. The whole machine is vibrating 3. The settings of firmware is incorrect ![](media/image106.jpeg)Extruding unevenly ------------------------------------------ 1. Feeding not smoothly 2. Hot end clogged 3. Layer thickness is too small 4. Extrusion width is incorrect (normal 100-150%) 5. Poor quality of filament 6. Extrusion force regulation for extrusion gear Motor shaking or abnormal sound ------------------------------- 1. The corresponding end stop could not be triggered when Home, check the wirings, and inspect any obstacles by manually moving the corresponding axis 2. The motor cable are not connected properly, check each connection and then inspect the cable routing for any faults File not printing or SD card failure ------------------------------------ 1. Remove the SD card and insert into PC. Open the Gcode files using text editor (eg. Notepad), and inspect if Gcode is readable or not. If files contains of multiple 2. SD card is not readable, ensure file name does not contain special characters or Change SD card 3. Reboot the machine and try again Print stopped halfway --------------------- 1. Check if the Gcode file is corrupted 2. Delete plugins in the Gcode file 3. Use print offline mode (SD card) instead of print online via USB Touch screen no response ------------------------ 1. Inspect if the touch screen has been pressed by the metal frame at the edge 2. Check if the cables and wires which connect the screen are loose 3. Check if the screen was broken,if so,please contact our service team

Use Quizgecko on...
Browser
Browser