SCBA Hose Folding Techniques

Podcast

Play an AI-generated podcast conversation about this lesson

Questions and Answers

What is the primary purpose of shutting off nozzles after attachment to hose lines?

To reduce the risk of accidental injury (correct)

To ensure proper hose alignment

To prevent water waste

To maintain consistent water pressure

When should hose lines be charged with water while being operated from heights?

Immediately upon reaching the desired height

Before any personnel are in position

After securing with proper safety protocols (correct)

Only when a backup team is present

What is the maximum angle for horizontal movement of hose streams from ladders?

45 degrees

30 degrees

60 degrees

15 degrees (correct)

What is a critical safety consideration when using hose streams from ladders?

To avoid sharp bends in the hose Signup and view all the answers

What action should be taken before lowering hose from heights?

Draining water at street level Signup and view all the answers

Why should members not leave one person alone on the nozzle inside a structure?

To provide assistance in case of an emergency Signup and view all the answers

Which of the following procedures is advised for the safe use of hose lines?

Shutting off nozzles when the flow ceases Signup and view all the answers

What should be done to relieve the strain from the hose line during operations?

Stagger positions of members holding the hose line Signup and view all the answers

What is the maximum pressure at which one-inch double jacketed hose should be tested?

400 psi Signup and view all the answers

How often should fire hose be tested?

Every 12 months Signup and view all the answers

When a section of hose is determined to be unreliable, what should be done?

Test it immediately Signup and view all the answers

Which hose type requires a maximum test pressure of 300 psi?

Rubber lined single and double jacketed hose Signup and view all the answers

What is the recommended procedure before testing a hose under pressure?

Lay out the hose with no sharp kinks or bends Signup and view all the answers

What should be done after attaching the shut-off butt during hose testing?

Bleed off the air Signup and view all the answers

What type of tag should be attached to a hose needing repair?

An F-175 tag with a clear description of the problem Signup and view all the answers

What is the recommended maximum length of hose to be laid out from the pump outlet during testing?

300 feet Signup and view all the answers

What is the correct position for the first fold of the hose when securing it to the SCBA bottle?

Approximately 10 inches below the bottle shut-off valve Signup and view all the answers

When securing the hose to the SCBA bottle, how should the folds be arranged?

Loosely in a 'U' shape, ensuring they are even Signup and view all the answers

Which strap should be placed where the hose forms the radius of the 'U'?

The first strap Signup and view all the answers

How should the nozzle be secured when it reaches the last fold of the hose?

By inverting the last fold and positioning it behind the last complete fold Signup and view all the answers

What is the minimum length for the nylon straps used in securing the hose?

24 inches Signup and view all the answers

Where should the second and third nylon straps be placed?

Around the hose opposite each other at approximately the middle of the SCBA bottle Signup and view all the answers

What is the purpose of the fourth and fifth nylon straps in the hose securing process?

To secure the hose approximately 8 inches from the end while encompassing the nozzle Signup and view all the answers

What is the correct procedure for securing the buckles of the nylon straps?

Secure buckles in a safe location Signup and view all the answers

Study Notes

SCBA Bottle Setup and Hose Handling

First fold of hose should be positioned against the SCBA bottle with the female coupling about 10 inches below the shut-off valve.
Alternate folds should form a loose "U" shape against the bottle, ensuring they remain even.
Upon reaching the male coupling, attach the nozzle and shut off. Invert the last fold to protect the nozzle behind the final fold of the pack.
Secure the first nylon strap around the radius of the "U," utilizing straps at least 24 inches long with the buckle in a safe location.
Place the second and third nylon straps around the hose opposite each other, positioned at the middle of the SCBA bottle, and secure buckles safely.
The fourth and fifth nylon straps should be placed approximately 8 inches from the end of the hose packs, ensuring one strap goes through the nozzle bale.

Safe Use of Hose Lines

Nozzles must be shut off after attachment or whenever the flow ceases for safety.
Charge hose lines from heights only after securing them in position.
Clear and secure hoses leading to upper floors from ladders to ensure safe operation.
Water should be drained at street level before lowering hoses from elevated positions.
Avoid directing water streams at individuals or premises unnecessarily.
Ensure care during hose stream use from ladders, limiting horizontal movement to 15 degrees from an "in-line" position.

Backing Up the Nozzle

Backing up the nozzle relieves strain caused by the reactionary force of water streams.
Maintain staggered positions among members holding the hose, keeping hose lines clear of sharp bends.
Notify the member at the nozzle before leaving the hose line, and ensure that no one is left alone on the nozzle.
If a hose needs repairs, mark the damaged area with black tape and roll the hose with the female coupling forming the core.
Use an F-175 tag describing the issue for easier identification and repair.

Hose Testing Procedures

Station Commanders must ensure all rubber-lined hoses are tested annually, especially new and repaired hoses.
Testing should occur immediately after receipt or repairs.
Maximum interval between tests is 12 months.
One-inch double jacketed hoses are tested at 400 psi, while other rubber-lined hoses are tested at 300 psi.
For testing, lay out hoses from the pump without kinks, up to a maximum length of 300 feet, and attach a shut-off butt to minimize hazards.
Bleed off air by opening the shut-off, elevating above discharge level, and filling the hose with water, controlling flow carefully.

Studying That Suits You

Use AI to generate personalized quizzes and flashcards to suit your learning preferences.

Description

This quiz focuses on the proper techniques for folding hose against a 45-minute SCBA bottle. Learn the correct positioning and method to ensure efficient storage and handling. Test your knowledge on best practices and safety protocols.