Cisco SRWE Module 6 EtherChannel PDF

17/08/2022 Module 6: EtherChannel Switching, Routing and Wireless Essentials v7.0 (SRWE) 1...

17/08/2022 Module 6: EtherChannel Switching, Routing and Wireless Essentials v7.0 (SRWE) 1 OFFICIAL Module Objectives Module Title: EtherChannel Module Objective: Troubleshoot EtherChannel on switched links. Topic Title Topic Objective EtherChannel Operation Describe EtherChannel technology. Configure EtherChannel Configure EtherChannel. Verify and Troubleshoot Troubleshoot EtherChannel. EtherChannel © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 2 OFFICIAL 2 1  17/08/2022 6.1 EtherChannel Operation © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 3 3 OFFICIAL EtherChannel Operation Link Aggregation There are scenarios in which more bandwidth or redundancy between devices is needed than what can be provided by a single link. Multiple links could be connected between devices to increase bandwidth. However, Spanning Tree Protocol (STP), which is enabled on Layer 2 devices like Cisco switches by default, will block redundant links to prevent switching loops. A link aggregation technology is needed that allows redundant links between devices that will not be blocked by STP. That technology is known as EtherChannel. EtherChannel is a link aggregation technology that groups multiple physical Ethernet links together into one single logical link. It is used to provide fault-tolerance, load sharing, increased bandwidth, and redundancy between switches, routers, and servers. EtherChannel technology makes it possible to combine the number of physical links between the switches to increase the overall speed of switch-to-switch communication. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 4 OFFICIAL 4 2  17/08/2022 OFFICIAL EtherChannel Operation EtherChannel EtherChannel technology was originally developed by Cisco as a LAN switch-to-switch technique of grouping several Fast Ethernet or Gigabit Ethernet ports into one logical channel. When an EtherChannel is configured, the resulting virtual interface is called a port channel. The physical interfaces are bundled together into a port channel interface, as shown in the figure. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 5 OFFICIAL 5 OFFICIAL EtherChannel Operation Advantages of EtherChannel EtherChannel technology has many advantages, including the following: Most configuration tasks can be done on the EtherChannel interface instead of on each individual port, ensuring configuration consistency throughout the links. EtherChannel relies on existing switch ports. There is no need to upgrade the link to a faster and more expensive connection to have more bandwidth. Load balancing takes place between links that are part of the same EtherChannel. EtherChannel creates an aggregation that is seen as one logical link. When several EtherChannel bundles exist between two switches, STP may block one of the bundles to prevent switching loops. When STP blocks one of the redundant links, it blocks the entire EtherChannel. This blocks all the ports belonging to that EtherChannel link. Where there is only one EtherChannel link, all physical links in the EtherChannel are active because STP sees only one (logical) link. EtherChannel provides redundancy because the overall link is seen as one logical connection. Additionally, the loss of one physical link within the channel does not create a change in the topology. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 6 OFFICIAL 6 3  17/08/2022 OFFICIAL EtherChannel Operation Implementation Restrictions EtherChannel has certain implementation restrictions, including the following: Interface types cannot be mixed. For example, Fast Ethernet and Gigabit Ethernet cannot be mixed within a single EtherChannel. Currently each EtherChannel can consist of up to eight compatibly-configured Ethernet ports. EtherChannel provides full-duplex bandwidth up to 800 Mbps (Fast EtherChannel) or 8 Gbps (Gigabit EtherChannel) between one switch and another switch or host. The Cisco Catalyst 2960 Layer 2 switch currently supports up to six EtherChannels. The individual EtherChannel group member port configuration must be consistent on both devices. If the physical ports of one side are configured as trunks, the physical ports of the other side must also be configured as trunks within the same native VLAN. Additionally, all ports in each EtherChannel link must be configured as Layer 2 ports. Each EtherChannel has a logical port channel interface. A configuration applied to the port channel interface affects all physical interfaces that are assigned to that interface. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 7 OFFICIAL 7 OFFICIAL EtherChannel Operation AutoNegotiation Protocols EtherChannels can be formed through negotiation using one of two protocols, Port Aggregation Protocol (PAgP) or Link Aggregation Control Protocol (LACP). These protocols allow ports with similar characteristics to form a channel through dynamic negotiation with adjoining switches. Note: It is also possible to configure a static or unconditional EtherChannel without PAgP or LACP. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 8 OFFICIAL 8 4  17/08/2022 OFFICIAL EtherChannel Operation PAgP Operation PAgP (pronounced “Pag - P”) is a Cisco-proprietary protocol that aids in the automatic creation of EtherChannel links. When an EtherChannel link is configured using PAgP, PAgP packets are sent between EtherChannel-capable ports to negotiate the forming of a channel. When PAgP identifies matched Ethernet links, it groups the links into an EtherChannel. The EtherChannel is then added to the spanning tree as a single port. When enabled, PAgP also manages the EtherChannel. PAgP packets are sent every 30 seconds. PAgP checks for configuration consistency and manages link additions and failures between two switches. It ensures that when an EtherChannel is created, all ports have the same type of configuration. Note: In EtherChannel, it is mandatory that all ports have the same speed, duplex setting, and VLAN information. Any port modification after the creation of the channel also changes all other channel ports. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 9 OFFICIAL 9 OFFICIAL EtherChannel Operation PAgP Operation (Cont.) PAgP helps create the EtherChannel link by detecting the configuration of each side and ensuring that links are compatible so that the EtherChannel link can be enabled when needed. The modes for PAgP as follows: On - This mode forces the interface to channel without PAgP. Interfaces configured in the on mode do not exchange PAgP packets. PAgP desirable - This PAgP mode places an interface in an active negotiating state in which the interface initiates negotiations with other interfaces by sending PAgP packets. PAgP auto - This PAgP mode places an interface in a passive negotiating state in which the interface responds to the PAgP packets that it receives but does not initiate PAgP negotiation. The modes must be compatible on each side. If one side is configured to be in auto mode, it is placed in a passive state, waiting for the other side to initiate the EtherChannel negotiation. If the other side is also set to auto, the negotiation never starts and the EtherChannel does not form. If all modes are disabled by using the no command, or if no mode is configured, then the EtherChannel is disabled. The on mode manually places the interface in an EtherChannel, without any negotiation. It works only if the other side is also set to on. If the other side is set to negotiate parameters through PAgP, no EtherChannel forms, because the side that is set to on mode does not negotiate. No negotiation between the two switches means there is no checking to make sure that all the links in the EtherChannel are terminating on the other side, or that there is PAgP compatibility on the other switch. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 10 OFFICIAL 10 5  17/08/2022 OFFICIAL EtherChannel Operation PAgP Mode Settings Example The table shows the various combination of PAgP modes on S1 and S2 and the resulting channel establishment outcome. S1 S2 Channel Establishment On On Yes On Desirable/Auto No Desirable Desirable Yes Desirable Auto Yes Auto Desirable Yes Auto Auto No © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 11 OFFICIAL 11 OFFICIAL EtherChannel Operation LACP Operation LACP is part of an IEEE specification (802.3ad) that allows several physical ports to be bundled to form a single logical channel. LACP allows a switch to negotiate an automatic bundle by sending LACP packets to the other switch. It performs a function similar to PAgP with Cisco EtherChannel. Because LACP is an IEEE standard, it can be used to facilitate EtherChannels in multivendor environments. On Cisco devices, both protocols are supported. LACP provides the same negotiation benefits as PAgP. LACP helps create the EtherChannel link by detecting the configuration of each side and making sure that they are compatible so that the EtherChannel link can be enabled when needed. The modes for LACP are as follows: On - This mode forces the interface to channel without LACP. Interfaces configured in the on mode do not exchange LACP packets. LACP active - This LACP mode places a port in an active negotiating state. In this state, the port initiates negotiations with other ports by sending LACP packets. LACP passive - This LACP mode places a port in a passive negotiating state. In this state, the port responds to the LACP packets that it receives but does not initiate LACP packet negotiation. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 12 OFFICIAL 12 6  17/08/2022 OFFICIAL EtherChannel Operation LACP Mode Settings Example The table shows the various combination of LACP modes on S1 and S2 and the resulting channel establishment outcome. S1 S2 Channel Establishment On On Yes On Active/Passive No Active Active Yes Active Passive Yes Passive Active Yes Passive Passive No © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 13 OFFICIAL 13 6.2 Configure EtherChannel © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 14 14 7  17/08/2022 OFFICIAL Configure EtherChannel Configuration Guidelines The following guidelines and restrictions are useful for configuring EtherChannel: EtherChannel support - All Ethernet interfaces must support EtherChannel with no requirement that interfaces be physically contiguous. Speed and duplex - Configure all interfaces in an EtherChannel to operate at the same speed and in the same duplex mode. VLAN match - All interfaces in the EtherChannel bundle must be assigned to the same VLAN or be configured as a trunk (shown in the figure). Range of VLANs - An EtherChannel supports the same allowed range of VLANs on all the interfaces in a trunking EtherChannel. If the allowed range of VLANs is not the same, the interfaces do not form an EtherChannel, even when they are set to auto or desirable mode. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 15 OFFICIAL 15 OFFICIAL Configure EtherChannel Configuration Guidelines (Cont.) The figure shows a configuration that would allow an EtherChannel to form between S1 and S2. If these settings must be changed, configure them in port channel interface configuration mode. Any configuration that is applied to the port channel interface also affects individual interfaces. However, configurations that are applied to the individual interfaces do not affect the port channel interface. Therefore, making configuration changes to an interface that is part of an EtherChannel link may cause interface compatibility issues. The port channel can be configured in access mode, trunk mode (most common), or on a routed port. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 16 OFFICIAL 16 8  17/08/2022 OFFICIAL Configure EtherChannel LACP Configuration Example Configuring EtherChannel with LACP requires the following three steps: Step 1. Specify the interfaces that compose the EtherChannel group using the interface range interface global configuration mode command. The range keyword allows you to select several interfaces and configure them all together. Step 2. Create the port channel interface with the channel-group identifier mode active command in interface range configuration mode. The identifier specifies a channel group number. The mode active keywords identify this as an LACP EtherChannel configuration. Step3. To change Layer 2 settings on the port channel interface, enter port channel interface configuration mode using the interface port-channel command, followed by the interface identifier. In the example, S1 is configured with an LACP EtherChannel. The port channel is configured as a trunk interface with the allowed VLANs specified. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 17 OFFICIAL 17 OFFICIAL Configure EtherChannel Packet Tracer – Configure EtherChannel In this Packet Tracer, you will complete the following objectives: Configure Basic Switch Settings Configure an EtherChannel with Cisco PAgP Configure and 802.3ad EtherChannel Configure a Redundant EtherChannel Link © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 18 OFFICIAL 18 9  17/08/2022 6.3 Verify and Troubleshoot EtherChannel © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 19 19 OFFICIAL Verify and Troubleshoot EtherChannel Verify EtherChannel As always, when you configure devices in your network, you must verify your configuration. If there are problems, you will also need to be able to troubleshoot and fix them. There are a number of commands to verify an EtherChannel configuration: The show interfaces port-channel command displays the general status of the port channel interface. The show etherchannel summary command displays one line of information per port channel. The show etherchannel port-channel command displays information about a specific port channel interface. The show interfaces etherchannel command can provide information about the role of a physical member interface of the EtherChannel. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 20 OFFICIAL 20 10  17/08/2022 OFFICIAL Verify and Troubleshoot EtherChannel Common Issues with EtherChannel Configurations All interfaces within an EtherChannel must have the same configuration of speed and duplex mode, native and allowed VLANs on trunks, and access VLAN on access ports. Ensuring these configurations will significantly reduce network problems related to EtherChannel. Common EtherChannel issues include the following: Assigned ports in the EtherChannel are not part of the same VLAN, or not configured as trunks. Ports with different native VLANs cannot form an EtherChannel. Trunking was configured on some of the ports that make up the EtherChannel, but not all of them. It is not recommended that you configure trunking mode on individual ports that make up the EtherChannel. When configuring a trunk on an EtherChannel, verify the trunking mode on the EtherChannel. If the allowed range of VLANs is not the same, the ports do not form an EtherChannel even when PAgP is set to the auto or desirable mode. The dynamic negotiation options for PAgP and LACP are not compatibly configured on both ends of the EtherChannel. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 21 OFFICIAL 21 OFFICIAL Verify and Troubleshoot EtherChannel Troubleshoot EtherChannel Example In the figure, interfaces F0/1 and F0/2 on switches S1 and S2 are connected with an EtherChannel. However, the EtherChannel is not operational. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 22 OFFICIAL 22 11  17/08/2022 OFFICIAL Verify and Troubleshoot EtherChannel Troubleshoot EtherChannel Example (Cont.) Step 1. View the EtherChannel Summary Information: The output of the show etherchannel summary command indicates that the EtherChannel is down. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 23 OFFICIAL 23 OFFICIAL Verify and Troubleshoot EtherChannel Troubleshoot EtherChannel Example (Cont.) Step 2. View Port Channel Configuration: In the show run | begin interface port-channel output, more detailed output indicates that there are incompatible PAgP modes configured on S1 and S2. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 24 OFFICIAL 24 12  17/08/2022 OFFICIAL Verify and Troubleshoot EtherChannel Troubleshoot EtherChannel Example (Cont.) Step 3: Correct the Misconfiguration: To correct the issue, the PAgP mode on the EtherChannel is changed to desirable. Note: EtherChannel and STP must interoperate. For this reason, the order in which EtherChannel-related commands are entered is important, which is why you see interface Port-Channel 1 removed and then re-added with the channel-group command, as opposed to directly changed. If one tries to change the configuration directly, STP errors cause the associated ports to go into blocking or errdisabled state. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 25 OFFICIAL 25 OFFICIAL Verify and Troubleshoot EtherChannel Troubleshoot EtherChannel Example (Cont.) Step 4. Verify EtherChannel is Operational: The EtherChannel is now active as verified by the output of the show etherchannel summary command. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 26 OFFICIAL 26 13  17/08/2022 OFFICIAL Verify and Troubleshoot EtherChannel Packet Tracer – Troubleshoot EtherChannel In this Packet Tracer, you will complete the following: Examine the Physical Layer and Correct Switch Port Mode Issues Identify and Correct Port Channel Assignment Issues Identify and Correct Port Channel Assignment Issues © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 27 OFFICIAL 27 6.4 Module Practice and Quiz © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 28 28 14  17/08/2022 OFFICIAL Module Practice and Quiz Packet Tracer – Implement EtherChannel In this Packet Tracer, you will complete the following: Build the Network Configure EtherChannel © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 29 OFFICIAL 29 OFFICIAL Module Practice and Quiz Lab – Implement EtherChannel In this lab, you will complete the following objectives: Part 1: Build the Network and Configure Basic Device Settings Part 2: Create VLANs and Assign Switch Ports Part 3: Configure 802.1Q Trunks between the Switches Part 4: Implement and Verify an EtherChannel between the switches © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 30 OFFICIAL 30 15  17/08/2022 OFFICIAL Module Practice and Quiz What Did I Learn In This Module? To increase bandwidth or redundancy, multiple links could be connected between devices. However, STP will block redundant links to prevent switching loops. EtherChannel is a link aggregation technology that allows redundant links between devices that will not be blocked by STP. EtherChannel groups multiple physical Ethernet links together into one single logical link. It provides fault-tolerance, load sharing, increased bandwidth, and redundancy between switches, routers, and servers. When an EtherChannel is configured, the resulting virtual interface is called a port channel. EtherChannels can be formed through negotiation using one of two protocols, PAgP or LACP. These protocols allow ports with similar characteristics to form a channel through dynamic negotiation with adjoining switches. When an EtherChannel link is configured using Cisco-proprietary PAgP, PAgP packets are sent between EtherChannel-capable ports to negotiate the forming of a channel. Modes for PAgP are On, PAgP desirable, and PAgP auto. LACP performs a function similar to PAgP with Cisco EtherChannel. Because LACP is an IEEE standard, it can be used to facilitate EtherChannels in multivendor environments. Modes for LACP are On, LACP active, and LACP passive. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 31 OFFICIAL 31 OFFICIAL Module Practice and Quiz What Did I Learn In This Module? (Cont.) The following guidelines and restrictions are useful for configuring EtherChannel: All Ethernet interfaces on all modules must support EtherChannel with no requirement that interfaces be physically contiguous, or on the same module. Configure all interfaces in an EtherChannel to operate at the same speed and in the same duplex mode. All interfaces in the EtherChannel bundle must be assigned to the same VLAN or be configured as a trunk. An EtherChannel supports the same allowed range of VLANs on all the interfaces in a trunking EtherChannel. Configuring EtherChannel with LACP requires three steps: Step 1. Specify the interfaces that compose the EtherChannel group using the interface range interface global configuration mode command. Step 2. Create the port channel interface with the channel-group identifier mode active command in interface range configuration mode. Step 3. To change Layer 2 settings on the port channel interface, enter port channel interface configuration mode using the interface port-channel command, followed by the interface identifier. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 32 OFFICIAL 32 16  17/08/2022 OFFICIAL Module Practice and Quiz What Did I Learn In This Module? (Cont.) There are a number of commands to verify an EtherChannel configuration including show interfaces port-channel, show etherchannel summary, show etherchannel port- channel, and show interfaces etherchannel. Common EtherChannel issues include the following: Assigned ports in the EtherChannel are not part of the same VLAN, or not configured as trunks. Ports with different native VLANs cannot form an EtherChannel. Trunking was configured on some of the ports that make up the EtherChannel, but not all of them. If the allowed range of VLANs is not the same, the ports do not form an EtherChannel even when PAgP is set to the auto or desirable mode. The dynamic negotiation options for PAgP and LACP are not compatibly configured on both ends of the EtherChannel. © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 33 OFFICIAL 33 Module 6: EtherChannel OFFICIAL New Terms and Commands Link Aggregation EtherChannel Port Channel Port Aggregation Protocol (PAgP) Link Aggregation Control Protocol (LACP) PAgP desirable PAgP auto LACP active LACP passive channel-group X mode [ desirable | auto | active | passive ] interface port-channel X show interfaces port-channel show etherchannel summary show etherchannel port-channel show interfaces etherchannel © 2019 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 34 OFFICIAL 34 17  17/08/2022 35 18