Petrochemical Processes PDF

Petrochemical Processes Crude Oil Processing and Production of Hydrocarbon Intermediates  PETROLEUM Naturally occurring yellowish-black liquid from geological formations beneath the earth’s surface. Refined to various fuels Consists of hydrocarbons of various molecul...

Petrochemical Processes Crude Oil Processing and Production of Hydrocarbon Intermediates  PETROLEUM Naturally occurring yellowish-black liquid from geological formations beneath the earth’s surface. Refined to various fuels Consists of hydrocarbons of various molecular weights and some organic compounds Crude and refined oil  Petrochemical Feedstocks The refinery products are: naphtha; gas oil and catalytic cracker gases. NOTE: In oil industry: gasoline fraction In petrochemical industry, naphtha is the petroleum fraction that boils between 20-80oC. Naphthas: mix of alkanes, cycloalaknes and aromatic hydrocarbons. Gas oils are mix of have the same components but with higher molecular weights. Gas oils are used in place of naphtha as a feedstocks for ethylene manufacture.  In USA, large scale cracking : cracker gases are the precursors for production of propylene and butene. In Europe and Japan, small scale cracking: cracker gases are sources for ethylene. Kerosine: chemical feedstock, manufacture of ethylene The Basic building Block Processes Petrochemical industry is based on intermediates. Known Petrochemical Processes: Thermal cracking; catalytic cracking and steam reforming.  Thermal Cracking Also known as steam cracking, is used for manufacture of ethylene. Feedstocks: ethane, propane, naphtha and gas oils. When ethane is cracked → ethylene Propane → propene + co-product Naphtha and gas oil → propylene, butene, butadiene and aromatic compounds. Catalytic reforming Used for making BTX. benzene, toluene, and xylene isomers Feedstock: naphtha Steam reforming Used for producing a mix of CO and H2. Intermediate for making NH3, CH3OH  Petrochemical Process Technology Petrochemical processes are normally Continuous Processes; the raw materials are continuously fed into the plant so as the products. Petrochemical plant would have one or more reaction systems. C6H6 + C2H4 → C6H5C2H5 → C6H5CH=CH2 + H2  Introduction Hydrocarbon intermediates are obtained by subjecting crude oil to various processing schemes. Primary distillation → simple fractions → used as fuels Small % of these fractions → raw materials (intermediates) for production of olefins, diolefins and aromatics. Further reaction may be required for other transformations.  Physical Separation processes Separating the components of crude oil without changing the chemical nature. Separation is based on the differences of certain physical properties of the constituents. e.g. boiling points, melting points,..etc. Atmospheric Distillation Separates crude oils into fractions with narrow boiling points. One or more fractionating columns are used. Starts by preheating the feed by exchange with the hot product streams. Feed is further heated to 320 oC by heating the stream pipes.  Feed inters the fractionator (30-50 fractionation tray). Steam is introduced from the bottom to strip light components. Efficiency  number of theoretical plates and the reflux ratio. Reflux Ratio: The ratio of vapor condensing back to the distillate. The higher the RR, the better separation of the mixture Flow diagram of atmospheric and vacuum distillation units:1 (1,3) heat exchangers; (2) desalter, (3,4) heater; (5) distillation column, (6) overhead condenser, (7–10) pump around streams, (11) vacuum distillation heater; (12) vacuum tower.  VACUUM DISTILLATION Increases the amount of the middle distillates Produces lubricating oil base stocks and asphalt. preheating by Vaccum Tower Residue Vaccum unit exchange with heater heated by hot product super heated steam Superheated steam → Decreases Phydrocarbons and Coke formation in furnace tubes. Temp: 400–440°C Absolute pressure: 25–40 mmHg. Products: Vacuum gas oil (VGO), lube oil base stocks, and asphalt. Asphalt may be used for paving roads or may be charged to a delayed coking unit.  ABSORPTION PROCESS Selectively removes a certain gas from a gas mixture using liquid adsorbent. Used in removal of acid gases. ADSORPTION PROCESS Using a large surface area adsorbent to selectively adsorb a gas or a liquid. e.g. Silica (SiO2), anhydrous alumina and zeolite molecular sieves (crystalline microporous alumino silicates. - Can be used to separate liquid mixtures. - Zeolite selectively adsorb liquid paraffins from Low octane naphtha. - Normal paraffins are important for detergent industry.  Adsorption also used to separate liquid mixtures. E.g. zeolite 5A selectively adsorbs n-paraffins from a low- octane naphtha fraction. Branched paraffins and aromatics in the mixture are not adsorbed. Desorption → displacement with another solvent. C10-C14 paraffins adsorbed from a kerosine or a gas oil is done in a liquid or a vapor phase adsorption process. The IsoSiv process is an isobaric, isothermal adsorption technique used to separate n-paraffins from gas oils @ 370°C and 100 psi. Desorption is achieved using n-pentane or n-hexane. The solvent is easily distilled from the heavier n-paraffins and then recycled.  SOLVENT EXTRACTION Liquid solvents are used to extract either desirable or undesirable compounds from a liquid mixture. Uses a solvent with high solvolytic power for certain compounds. e.g. ethylene to extract aromatic hydrocarbons from a reformate mixture (a liquid paraffinic and aromatic product from catalytic reforming). The raffinate, which is mainly paraffins, is freed from traces of ethylene glycol by distillation. Others: liquid sulfur dioxide and sulfolane (tetramethylene sulfone). The sulfolane process is a versatile extractant for producing high purity BTX aromatics (benzene, toluene, and xylenes). It also extracts aromatics from kerosines to produce low-aromatic jet fuels. Solvent extraction used to reduce asphaltenes and metals from heavy fractions and residues before using them in catalytic cracking. The IFP deasphalting process:4 (1,2) extractor, (3-6) solvent recovery towers.  CONVERSION PROCESSES Purpose : To upgrade lower-value materials To improve the characteristics of a fuel. lower octane → to a higher octane reformate product. To reduce harmful impurities in petroleum fractions and residues. To avoid poisoning certain processing catalysts. Conversion processes are either thermal, or Catalytic  THERMAL CONVERSION PROCESSES Coking Processes Thermal cracking process designed to handle heavy residues with high asphaltene and metal contents. These residues contain impurities which deactivate and poison the catalysts. Thermal Cracking Reactions Also Flexicoking is a fluid coking process in which the coke is gasified with air and steam. The resulting gas mixture partially provides process heat.  Delayed Coking The reactor system consists of a short contact-time heater coupled to a large drum in which the preheated feed “soaks” on a batch basis. Coke gradually forms in the drum. A delayed coking unit has at least a pair of drums. When the coke reaches a predetermined level in one drum, flow is diverted to the other so that the process is continuous. Vapors from the top of the drum are directed to the fractionator where they are separated into gases, naphtha, kerosine, and gas oil. Decoking the filled drum can be accomplished by a hydraulic system using several water jets under at least 3,000 pounds per square inch gauge.