How To Make and Install Signs PDF

and silicone on the back Timestamp WO# Sign Type How do we Make? How do we Install? of the brackets to fix the...

and silicone on the back Timestamp WO# Sign Type How do we Make? How do we Install? of the brackets to fix the brackets and sign panel How do we Design it? ( Put double-sided tape layouts ) Designer - Cut out 2x8" insert from front panel - Adhere spacer atop backer using adhesive - Adhere front panel atop spacer using adhesive - Adhere 3/4" vinyl cut font to front panel (Bright White) 10/10/2022 17:58:27 22459 ADA 10/11/2022 12:41:30 082222 - Use braille insertion tool to embed spheres into sign 10/13/2022 15:24:11 22265 ADA 10/13/2022 15:47:27 22199 - Laser-cut frosted acrylic backer (8x14.75", 1/8" thick, Pantone 108C Yellow) - Laser-cut frosted acrylic panel (8x14.75", 3/16" thick, white) - Cut out stair symbol from front panel Plaque / Vendor - Cut out "STAIRS" from front panel - Adhere 5/8" vinyl cut font to front panel (103A Black) - Use braille insertion tool to embed spheres into sign ADA with Insert - Direct print 708 White font onto inserts (A: 2x8", B: 2x4", C: - Laser-cut painted acrylic sign panel (6x8", 1/16" thick) 1x12", D: 1x12" x3) - Drop inserts into frame (6x12", 156 Bronze) - Laser-cut painted acrylic backer panel (6x8", 1/8" thick) - Notch endcaps to either side of frame - Laser-cut clear acrylic spacer (6x8", 1/32" thick) - Router-cut acrylic letters (14", 1" thick, 2718 Ivory - Cut out 2x8" insert from front panel to the wall. - Sandwich spacer between sign and backer using adhesive - Adhere 3/4" vinyl cut font to front panel - Use braille insertion tool to embed spheres into sign - Cut out two aluminum pieces (17x3" each) with router - Cut out one aluminum piece (15x2") with router - Laser-cut out one clear acrylic piece (15x2", offset by 1/8") - Apply two strips of double-sided tape to the back of backer panel - Brush aluminum in one direction consistently across all three - Affix sign to wall, 9" from door, 57" from ground strips - Bend each 17x3" strip at the 15" mark 10/12/2022 12:59:34 unknown, Metal "I" from the office Fabricate - Cast Letter - Paint one side of each bent strip white - Weld the two inverted L-shaped aluminum strips into a rectangular shape - Weld the 15x2" strip to close one end of the rectangle - Drill mounting holes into one 2" end of the rectange - Use anchor rivets to hold clear acrylic piece over open end of the rectangle - (Should be noted that this method is relatively 10/12/2022 14:14:58 16232 ADA 10/12/2022 14:34:31 unknown, outdated. The new letter bender would negate the need to weld the two aluminum pieces, instead bending one into an "I" shape. Additionally, drain holes are included more often now) - Take out anchor rivets to remove clear acrylic cover - Insert screws into mounting holes at an angle - Laser-cut painted acrylic sign panel (9x5", 1/8" thick, 602 - Anchor clear acrylic piece back on Burgundy) - Laser-cut painted acrylic sign panel (9x5", offset by tan restroom sign from office ADA 10/12/2022 14:36:22 1/8" AND by -1/8", 1/16" thick, White) - Cut out painted acrylic backer with router (9x5", 3/8" thick, Black) - Adhere front piece to backer using adhesive - Adhere vinyl cut font to front panel (1/16" thick, white) - Adhere 1/16" thick white acrylic to front panel using adhesive unknown, black restroom sign from office ADA 10/12/2022 - Use braille insertion tool to embed spheres into sign - Apply two strips of double-sided tape to the back of backer panel - Laser-cut painted acrylic sign panel (8x8", 1/8" thick, tan) - Affix sign to wall, 9" from door, 57" from ground - Adhere vinyl cut font to front panel (1/16" thick, blue) - Adhere vinyl ADA restroom symbols to front panel using adhesive (1/16" thick, blue) 14:47:01 unknow, orange sign from office ADA - Use braille insertion tool to embed spheres into sign - Apply two strips of double-sided tape to the back of panel - Affix sign to wall, 9" from door, 57" from ground - Laser-cut painted acrylic sign panel (8x8", 1/8" thick, Black) - Adhere vinyl cut font to front panel (1/16" thick, White) - Adhere vinyl ADA male restroom symbols to front panel using adhesive (1/16" thick, White) - Use braille insertion tool to embed spheres into sign - Apply two strips of double-sided tape to the back of panel 10/12/2022 14:56:20 unknown, "west stair" sign from office ADA - Affix sign to wall, 9" from door, 57" from ground - Laser-cut painted acrylic sign panel (8.5x3", 1/8" thick, orange) - Laser-cut painted acrylic sign panel (8.5x3", offset by 1/8", 1/8" thick, silver) - Adhere vinyl cut font to front panel (1/16" thick, silver) - Adhere 1/8" thick silver acrylic to front panel using adhesive - Apply 4 squares of double-sided tape to the back corners of panel - Use braille insertion tool to embed spheres into sign - Affix sign to wall, 9" from door, 57" center from ground 10/12/2022 16:19:16 22451 Fabricate - Cast Letter - Laser-cut painted acrylic sign panel (7.5x7.5", 1/8" thick, White) - Laser-cut painted acrylic sign panel (7.5x4.5", 1/8" thick, grey) - Laser-cut painted acrylic backer (7.5x11", 1/4" thick, grey) - Adhere vinyl cut font to 7.5x4.5" panel (1/16" thick, White) - Apply 4 squares of double-sided tape to the back corners of panel - Use braille insertion tool to embed spheres into same panel - - Affix sign to wall, 9" from door, 57" center from ground Adhere vinyl ADA stair symbol to 7.5x7.5" panel (1/16" thick, grey) - Router-cut painted acrylic backer (12x70", 1/4" thick, Sw9165) - Router-cut painted aluminum letters (4 1/8" high, Helvetica, E E E 10/13/2022 15:09:00 22419 ADA with Insert C C N N O F R) - Surface print letters on flatbed printer (4310 Dove Grey) - Mount letters to backer, spaced 2.5" from one another - - Drill 3-4 stud holes into each letter (1/4") Mount fixture to wall, 18 3/4" from left, 50" from ground - Drill 6 mounting holes into backer (1/4") - Laser-cut painted acrylic sign panel (6x8", 1/16" thick. Cobalt Blue) - Laser-cut painted acrylic backer panel (6x8", 1/8" thick, Cobalt Blue) - Laser-cut clear acrylic spacer (6x8", 1/16" thick)  - Affix sign to wall, 9" from door, centered 57" from ground Affix sign to wall, 9" from door, centered 57" from ground - Mount via adhesive strips on back of frame - Affix sign to wall, 9" from door, centered 57" from ground - Apply two strips of tape and silicone to the back of panel - - Apply two strips of double-sided tape to the back of panel - Drill stud holes into letters (3/4") Fasten studded letters to brick wall 10/13/2022 16:37:20 22269 Fabricate - Cast Letter 10/17/2022 9:02:20 22502 Other - CUT 1/4" Thick Acrylic (Size: 3" x 10.5"), Paint it with (PMS Cool Grey 3U, Surface) - Text to be RE - 2 faced tape (4'4" AFF) Open Corel file in Drive Folder. Get the corect drawing and lay it out in Signlab. - Direct print 713 Sand font onto inserts B and C Timestamp WO# Sign Type How do we Make? How do we Install? - Apply photopolymer braille dots onto inserts B and C - Laser-cut three acrylic inserts (711 Ash, A: 6x8", B and C: 2x8) How do we Design it? ( - Direct print 713 Sand ADA symbol onto insert A layouts ) Designer - Drop inserts into frame (10x8", 156 Bronze) - create 4x18" rectangle - Notch endcaps to either side of frame - Cut out plastic frame (4x18", 1/2" thick, Black, square corners) - Mount via adhesive strips on back of frame - Affix sign to wall, 9" from door, centered 57" from ground 10/17/2022 9:55:24 22199 ADA with Insert - Laser-cut acrylic sign panel (3 7/8"x17 7/8", 1/8" thick, Duets Black, square corners) - Apply two strips of tape and silicone to the back of panel - create offset -1/8" rectangle 10/17/2022 10:10:45 22411 ADA - Adhere 1 1/2" vinyl cut font to front panel (113A White) - Affix sign to wall, centered 9" from door, 57" from ground - Helvetica Narrow Bold font, center align,