ch4 magnetism.pdf

Chapter Four MOVING CHARGES AND MAGNETISM 4.1 INTRODUCTION Both Electricity and Magnetism have been known for more than 2000 years. However, it was only about 200 years ago, in 1820, that it was realised that they were intimately related. During a lecture demonstration...

Chapter Four MOVING CHARGES AND MAGNETISM 4.1 INTRODUCTION Both Electricity and Magnetism have been known for more than 2000 years. However, it was only about 200 years ago, in 1820, that it was realised that they were intimately related. During a lecture demonstration in the summer of 1820, Danish physicist Hans Christian Oersted noticed that a current in a straight wire caused a noticeable deflection in a nearby magnetic compass needle. He investigated this phenomenon. He found that the alignment of the needle is tangential to an imaginary circle which has the straight wire as its centre and has its plane perpendicular to the wire. This situation is depicted in Fig.4.1(a). It is noticeable when the current is large and the needle sufficiently close to the wire so that the earth’s magnetic field may be ignored. Reversing the direction of the current reverses the orientation of the needle [Fig. 4.1(b)]. The deflection increases on increasing the current or bringing the needle closer to the wire. Iron filings sprinkled around the wire arrange themselves in concentric circles with the wire as the centre [Fig. 4.1(c)]. Oersted concluded that moving charges or currents produced a magnetic field in the surrounding space. Following this, there was intense experimentation. In 1864, the laws obeyed by electricity and magnetism were unified and formulated by 2024-25  Physics James Maxwell who then realised that light was electromagnetic waves. Radio waves were discovered by Hertz, and produced by J.C.Bose and G. Marconi by the end of the 19th century. A remarkable scientific and technological progress took place in the 20th century. This was due to our increased understanding of electromagnetism and the invention of devices for production, amplification, transmission and detection of electromagnetic waves. FIGURE 4.1 The magnetic field due to a straight long current-carrying wire. The wire is perpendicular to the plane of the paper. A ring of compass needles surrounds the wire. The orientation of the needles is shown when (a) the current emerges out of the plane of the paper, (b) the current moves into the plane of the paper. (c) The arrangement of iron filings around the wire. The darkened ends of the needle represent north poles. The effect of the earth’s magnetic field is neglected. In this chapter, we will see how magnetic field exerts forces on moving charged particles, like electrons, protons, HANS CHRISTIAN OERSTED (1777–1851) and current-carrying wires. We shall also learn how currents produce magnetic fields. We shall see how particles can be accelerated to very high energies in a cyclotron. We shall study how currents and voltages are detected by a galvanometer. In this and subsequent Chapter on magnetism, we adopt the following convention: A current or a field (electric or magnetic) emerging out of the plane of the paper is depicted by a dot (¤). A current or a field going into the plane of the paper is depicted by a cross (  )*. Hans Christian Oersted Figures. 4.1(a) and 4.1(b) correspond to these two (1777–1851) Danish situations, respectively. physicist and chemist, professor at Copenhagen. He observed that a 4.2 MAGNETIC FORCE compass needle suffers a 4.2.1 Sources and fields deflection when placed near a wire carrying an Before we introduce the concept of a magnetic field B, we electric current. This shall recapitulate what we have learnt in Chapter 1 about discovery gave the first the electric field E. We have seen that the interaction empirical evidence of a between two charges can be considered in two stages. connection between electric The charge Q, the source of the field, produces an electric and magnetic phenomena. field E, where * A dot appears like the tip of an arrow pointed at you, a cross is like the feathered 108 tail of an arrow moving away from you. 2024-25  Moving Charges and Magnetism E = Q r̂ / (4pe0)r2 (4.1) where r̂ is unit vector along r, and the field E is a vector field. A charge q interacts with this field and experiences a force F given by F = q E = q Q r̂ / (4pe0) r 2 (4.2) As pointed out in the Chapter 1, the field E is not just an artefact but has a physical role. It can convey energy and momentum and is not established instantaneously but takes finite time to propagate. The concept of a field was specially stressed by Faraday and was incorporated by Maxwell in his unification of electricity and magnetism. In addition to depending on each point in space, it can also vary with time, i.e., be a function of time. In our HENDRIK ANTOON LORENTZ (1853 – 1928) Hendrik Antoon Lorentz discussions in this chapter, we will assume that the fields (1853 – 1928) Dutch do not change with time. theoretical physicist, The field at a particular point can be due to one or professor at Leiden. He investigated the more charges. If there are more charges the fields add relationship between vectorially. You have already learnt in Chapter 1 that this electricity, magnetism, and is called the principle of superposition. Once the field is mechanics. In order to known, the force on a test charge is given by Eq. (4.2). explain the observed effect Just as static charges produce an electric field, the of magnetic fields on currents or moving charges produce (in addition) a emitters of light (Zeeman magnetic field, denoted by B (r), again a vector field. It effect), he postulated the has several basic properties identical to the electric field. existence of electric charges in the atom, for which he It is defined at each point in space (and can in addition was awarded the Nobel Prize depend on time). Experimentally, it is found to obey the in 1902. He derived a set of principle of superposition: the magnetic field of several transformation equations sources is the vector addition of magnetic field of each (known after him, as individual source. Lorentz transformation equations) by some tangled 4.2.2 Magnetic Field, Lorentz Force mathematical arguments, but he was not aware that Let us suppose that there is a point charge q (moving these equations hinge on a with a velocity v and, located at r at a given time t) in new concept of space and presence of both the electric field E (r) and the magnetic time. field B (r). The force on an electric charge q due to both of them can be written as F = q [ E (r) + v × B (r)] º Felectric +Fmagnetic (4.3) This force was given first by H.A. Lorentz based on the extensive experiments of Ampere and others. It is called the Lorentz force. You have already studied in detail the force due to the electric field. If we look at the interaction with the magnetic field, we find the following features. (i) It depends on q, v and B (charge of the particle, the velocity and the magnetic field). Force on a negative charge is opposite to that on a positive charge. (ii) The magnetic force q [ v × B ] includes a vector product of velocity and magnetic field. The vector product makes the force due to magnetic 109 2024-25  Physics field vanish (become zero) if velocity and magnetic field are parallel or anti-parallel. The force acts in a (sideways) direction perpendicular to both the velocity and the magnetic field. Its direction is given by the screw rule or right hand rule for vector (or cross) product as illustrated in Fig. 4.2. (iii) The magnetic force is zero if charge is not moving (as then |v|= 0). Only a moving charge feels the magnetic force. The expression for the magnetic force helps us to define the unit of the magnetic field, if one FIGURE 4.2 The direction of the magnetic takes q, F and v, all to be unity in the force force acting on a charged particle. (a) The equation F = q [ v × B] =q v B sin q n̂ , where q is force on a positively charged particle with the angle between v and B [see Fig. 4.2 (a)]. The velocity v and making an angle q with the magnitude of magnetic field B is 1 SI unit, when magnetic field B is given by the right-hand the force acting on a unit charge (1 C), moving rule. (b) A moving charged particle q is perpendicular to B with a speed 1m/s, is one deflected in an opposite sense to –q in the presence of magnetic field. newton. Dimensionally, we have [B] = [F/qv] and the unit of B are Newton second / (coulomb metre). This unit is called tesla ( T ) named after Nikola Tesla (1856 – 1943). Tesla is a rather large unit. A smaller unit (non-SI) called gauss (=10–4 tesla) is also often used. The earth’s magnetic field is about 3.6 × 10–5 T. 4.2.3 Magnetic force on a current-carrying conductor We can extend the analysis for force due to magnetic field on a single moving charge to a straight rod carrying current. Consider a rod of a uniform cross-sectional area A and length l. We shall assume one kind of mobile carriers as in a conductor (here electrons). Let the number density of these mobile charge carriers in it be n. Then the total number of mobile charge carriers in it is nlA. For a steady current I in this conducting rod, we may assume that each mobile carrier has an average drift velocity vd (see Chapter 3). In the presence of an external magnetic field B, the force on these carriers is: F = (nlA)q vd ´ B where q is the value of the charge on a carrier. Now nq vd is the current density j and |(nq vd )|A is the current I (see Chapter 3 for the discussion of current and current density). Thus, F = [(nq vd )l A] × B = [ jAl ] ´ B = Il ´ B (4.4) where l is a vector of magnitude l, the length of the rod, and with a direction identical to the current I. Note that the current I is not a vector. In the last step leading to Eq. (4.4), we have transferred the vector sign from j to l. Equation (4.4) holds for a straight rod. In this equation, B is the external magnetic field. It is not the field produced by the current-carrying rod. If the wire has an arbitrary shape we can calculate the Lorentz force on it by considering it as a collection of linear strips dlj and summing F   Idl j × B j 110 This summation can be converted to an integral in most cases. 2024-25  Moving Charges and Magnetism Example 4.1 A straight wire of mass 200 g and length 1.5 m carries a current of 2 A. It is suspended in mid-air by a uniform horizontal magnetic field B (Fig. 4.3). What is the magnitude of the magnetic field? FIGURE 4.3 Solution From Eq. (4.4), we find that there is an upward force F, of magnitude IlB,. For mid-air suspension, this must be balanced by the force due to gravity: m g = I lB http://www.phys.hawaii.edu/~teb/optics/java/partmagn/index.html Interactive demonstration: Charged particles moving in a magnetic field. mg B= Il EXAMPLE 4.1 0.2 × 9.8 = = 0.65 T 2 × 1.5 Note that it would have been sufficient to specify m/l, the mass per unit length of the wire. The earth’s magnetic field is approximately 4 × 10–5 T and we have ignored it. Example 4.2 If the magnetic field is parallel to the positive y-axis and the charged particle is moving along the positive x-axis (Fig. 4.4), which way would the Lorentz force be for (a) an electron (negative charge), (b) a proton (positive charge). FIGURE 4.4 EXAMPLE 4.2 Solution The velocity v of particle is along the x-axis, while B, the magnetic field is along the y-axis, so v × B is along the z-axis (screw rule or right-hand thumb rule). So, (a) for electron it will be along –z axis. (b) for a positive charge (proton) the force is along +z axis. 111 2024-25  Physics 4.3 MOTION IN A MAGNETIC FIELD We will now consider, in greater detail, the motion of a charge moving in a magnetic field. We have learnt in Mechanics (see Class XI book, Chapter 5) that a force on a particle does work if the force has a component along (or opposed to) the direction of motion of the particle. In the case of motion of a charge in a magnetic field, the magnetic force is perpendicular to the velocity of the particle. So no work is done and no change in the magnitude of the velocity is produced (though the direction of momentum may be changed). [Notice that this is unlike the force due to an electric field, q E, which can have a component parallel (or antiparallel) to motion and thus can transfer energy in addition to momentum.] We shall consider motion of a charged particle in a uniform magnetic field. First consider the case of v perpendicular to B. The perpendicular force, q v × B, acts as a centripetal force and produces a circular motion perpendicular to the magnetic field. The particle will describe a circle if v and B are perpendicular to each other (Fig. 4.5). If velocity has a component along B, this component remains unchanged as the motion along the magnetic field will not be affected by the magnetic field. The motion in a plane perpendicular to B is as before a circular one, thereby producing a helical motion (Fig. 4.6). You have already learnt in earlier classes (See Class XI, Chapter 3) that if r is the radius of the circular path of a particle, then a force of m v2 / r, acts perpendicular to the path towards the centre of the circle, and is called the centripetal force. If the FIGURE 4.5 Circular motion velocity v is perpendicular to the magnetic field B, the magnetic force is perpendicular to both v and B and acts like a centripetal force. It has a magnitude q v B. Equating the two expressions for centripetal force, m v 2/r = q v B, which gives r = m v / qB (4.5) for the radius of the circle described by the charged particle. The larger the momentum, the larger is the radius and bigger the circle described. If ω is the angular frequency, then v = ω r. So, ω = 2π ν = q B/ m [4.6(a)] which is independent of the velocity or energy. Here ν is the frequency of rotation. The independence of ν from energy has important application in the design of a cyclotron (see Section 4.4.2). The time taken for one revolution is T= 2π/ω FIGURE 4.6 Helical motion ≡ 1/ν. If there is a component of the velocity 112 parallel to the magnetic field (denoted by v||), it will make the particle 2024-25  Moving Charges and Magnetism move along the field and the path of the particle would be a helical one (Fig. 4.6). The distance moved along the magnetic field in one rotation is called pitch p. Using Eq. [4.6 (a)], we have p = v||T = 2πm v|| / q B [4.6(b)] The radius of the circular component of motion is called the radius of the helix. Example 4.3 What is the radius of the path of an electron (mass 9 × 10-31 kg and charge 1.6 × 10–19 C) moving at a speed of 3 ×107 m/s in a magnetic field of 6 × 10–4 T perpendicular to it? What is its frequency? Calculate its energy in keV. ( 1 eV = 1.6 × 10–19 J). Solution Using Eq. (4.5) we find EXAMPLE 4.3 r = m v / (qB ) = 9 ×10–31 kg × 3 × 107 m s–1 / ( 1.6 × 10–19 C × 6 × 10–4 T ) = 28 × 10–2 m = 28 cm ν = v / (2 πr) = 17×106 s–1 = 17×106 Hz =17 MHz. E = (½ )mv 2 = (½ ) 9 × 10–31 kg × 9 × 1014 m2/s2 = 40.5 ×10–17 J ≈ 4×10 J = 2.5 keV. –16 4.4 M A G N E T I C F I E L D D U E T O A CURRENT ELEMENT, BIOT-SAVART LAW All magnetic fields that we know are due to currents (or moving charges) and due to intrinsic magnetic moments of particles. Here, we shall study the relation between current and the magnetic field it produces. It is given by the Biot-Savart’s law. Fig. 4.7 shows a finite conductor XY carrying current I. Consider an infinitesimal element dl of the conductor. The magnetic field dB due to this element is to be determined at a point P which is at a distance r from it. Let θ be the angle between dl and the displacement vector r. According to Biot-Savart’s law, the magnitude of the magnetic field dB is proportional to the current I, the element length |dl|, and inversely proportional to the square of the distance r. Its direction* is perpendicular to the plane containing dl and r. Thus, in vector notation, I dl × r FIGURE 4.7 Illustration of dB ∝ the Biot-Savart law. The r3 current element I dl µ I dl × r produces a field dB at a = 0 [4.7(a)] distance r. The ⊗ sign 4π r3 indicates that the where µ0/4π is a constant of proportionality. The above expression field is perpendicular holds when the medium is vacuum. to the plane of this page and directed into it. * The sense of dl × r is also given by the Right Hand Screw rule : Look at the plane containing vectors dl and r. Imagine moving from the first vector towards second vector. If the movement is anticlockwise, the resultant is towards you. If it is clockwise, the resultant is away from you. 113 2024-25  Physics The magnitude of this field is, µ0 I dl sin θ dB = [4.7(b)] 4π r2 where we have used the property of cross-product. Equation [4.7 (a)] constitutes our basic equation for the magnetic field. The proportionality constant in SI units has the exact value, µ0 = 10 −7 Tm/A [4.7(c)] 4π We call µ0 the permeability of free space (or vacuum). The Biot-Savart law for the magnetic field has certain similarities, as well as, differences with the Coulomb’s law for the electrostatic field. Some of these are: (i) Both are long range, since both depend inversely on the square of distance from the source to the point of interest. The principle of superposition applies to both fields. [In this connection, note that the magnetic field is linear in the source I dl just as the electrostatic field is linear in its source: the electric charge.] (ii) The electrostatic field is produced by a scalar source, namely, the electric charge. The magnetic field is produced by a vector source I dl. (iii) The electrostatic field is along the displacement vector joining the source and the field point. The magnetic field is perpendicular to the plane containing the displacement vector r and the current element I dl. (iv) There is an angle dependence in the Biot-Savart law which is not present in the electrostatic case. In Fig. 4.7, the magnetic field at any point in the direction of dl (the dashed line) is zero. Along this line, θ = 0, sin θ = 0 and from Eq. [4.7(a)], |dB| = 0. There is an interesting relation between ε0, the permittivity of free space; µ , the permeability of free space; and c, the speed of light in vacuum: 0 µ0 ε 0 µ0 = ( 4 π ε 0 ) 4π = 1 9 × 109 (10 ) = (3 × 10 −7 1 8 2 ) = 1 c2 We will discuss this connection further in Chapter 8 on the electromagnetic waves. Since the speed of light in vacuum is constant, the product µ0ε0 is fixed in magnitude. Choosing the value of either ε0 or µ0, fixes the value of the other. In SI units, µ0 is fixed to be equal to 4π × 10–7 in magnitude. Example 4.4 An element ∆l = ∆x ˆi is placed at the origin and carries a large current I = 10 A (Fig. 4.8). What is the magnetic field on the y- axis at a distance of 0.5 m. ∆x = 1 cm. EXAMPLE 4.4 114 FIGURE 4.8 2024-25  Moving Charges and Magnetism Solution µ 0 I dl sin θ |dB | = [using Eq. (4.7)] 4π r2 Tm dl = ∆x = 10 −2 m , I = 10 A, r = 0.5 m = y, µ0 / 4 π = 10 −7 A θ = 90° ; sin θ = 1 10−7 × 10 × 10 −2 dB = = 4 × 10–8 T 25 × 10 −2 The direction of the field is in the +z-direction. This is so since, ( ) EXAMPLE 4.4 dl × r = ∆x ˆi × y ˆj = y ∆x ˆi × ˆj = y ∆x k ˆ We remind you of the following cyclic property of cross-products, ˆi × ˆj = k ˆ ; ˆj × k ˆ = ˆi ; k ˆ × ˆi = ˆj Note that the field is small in magnitude. In the next section, we shall use the Biot-Savart law to calculate the magnetic field due to a circular loop. 4.5 MAGNETIC FIELD ON THE AXIS OF A CIRCULAR CURRENT LOOP In this section, we shall evaluate the magnetic field due to a circular coil along its axis. The evaluation entails summing up the effect of infinitesimal current elements (I dl) mentioned in the previous section. We assume that the current I is steady and that the evaluation is carried out in free space (i.e., vacuum). Fig. 4.9 depicts a circular loop carrying a steady current I. The loop is placed in the plane with its centre at the origin O and has a radius R. The x-axis is the axis of the loop. We wish to calculate the magnetic field at the point P on this axis. Let x be the distance of P from the centre O of the loop. Consider a conducting element dl of the loop. This is FIGURE 4.9 Magnetic field on the shown in Fig. 4.9. The magnitude dB of the magnetic axis of a current carrying circular field due to dl is given by the Biot-Savart law [Eq. 4.7(a)], loop of radius R. Shown are the µ0 I dl × r magnetic field dB (due to a line dB = (4.8) element dl ) and its 4π r3 components along and Now r 2 = x 2 + R 2. Further, any element of the loop perpendicular to the axis. will be perpendicular to the displacement vector from the element to the axial point. For example, the element dl in Fig. 4.9 is in the plane, whereas, the displacement vector r from dl to the axial point P is in the plane. Hence |dl × r|=r dl. Thus, µ0 Idl dB = ( 4π x + R 2 2 ) (4.9) 115 2024-25  Physics The direction of dB is shown in Fig. 4.9. It is perpendicular to the plane formed by dl and r. It has an x-component dBx and a component perpendicular to x-axis, dB⊥. When the components perpendicular to the x-axis are summed over, they cancel out and we obtain a null result. For example, the dB ⊥ component due to dl is cancelled by the contribution due to the diametrically opposite dl element, shown in Fig. 4.9. Thus, only the x-component survives. The net contribution along x-direction can be obtained by integrating dBx = dB cos θ over the loop. For Fig. 4.9, R cos θ = (4.10) ( x + R 2 )1/ 2 2 From Eqs. (4.9) and (4.10), µ0 Idl R dB x = (x ) 3/2 4π 2 + R2 The summation of elements dl over the loop yields 2πR, the circumference of the loop. Thus, the magnetic field at P due to entire circular loop is µ0 I R 2 B = B x ˆi = ˆi ( ) 2 3/2 (4.11) 2 x +R 2 As a special case of the above result, we may obtain the field at the centre of the loop. Here x = 0, and we obtain, µ I B0 = 0 ˆi (4.12) 2R The magnetic field lines due to a circular wire form closed loops and are shown in Fig. 4.10. The direction of the magnetic field is given by (another) right-hand thumb rule stated below: Curl the palm of your right hand around the circular wire with the fingers pointing in the direction of the current. The right-hand thumb gives the direction of the magnetic field. FIGURE 4.10 The magnetic field lines for a current loop. The direction of the field is given by the right-hand thumb rule described in the text. The upper side of the loop may be thought of as the north pole and the lower 116 side as the south pole of a magnet. 2024-25  Moving Charges and Magnetism Example 4.5 A straight wire carrying a current of 12 A is bent into a semi-circular arc of radius 2.0 cm as shown in Fig. 4.11(a). Consider the magnetic field B at the centre of the arc. (a) What is the magnetic field due to the straight segments? (b) In what way the contribution to B from the semicircle differs from that of a circular loop and in what way does it resemble? (c) Would your answer be different if the wire were bent into a semi-circular arc of the same radius but in the opposite way as shown in Fig. 4.11(b)? FIGURE 4.11 Solution (a) dl and r for each element of the straight segments are parallel. Therefore, dl × r = 0. Straight segments do not contribute to |B|. (b) For all segments of the semicircular arc, dl × r are all parallel to EXAMPLE 4.5 each other (into the plane of the paper). All such contributions add up in magnitude. Hence direction of B for a semicircular arc is given by the right-hand rule and magnitude is half that of a circular loop. Thus B is 1.9 × 10–4 T normal to the plane of the paper going into it. (c) Same magnitude of B but opposite in direction to that in (b). Example 4.6 Consider a tightly wound 100 turn coil of radius 10 cm, carrying a current of 1 A. What is the magnitude of the magnetic field at the centre of the coil? Solution Since the coil is tightly wound, we may take each circular EXAMPLE 4.6 element to have the same radius R = 10 cm = 0.1 m. The number of turns N = 100. The magnitude of the magnetic field is, µ0 NI 4 π × 10 –7 × 102 × 1 B= = −4 = 2π × 10 −4 = 6.28 × 10 T 2R 2 × 10 –1 4.6 AMPERE’S CIRCUITAL LAW There is an alternative and appealing way in which the Biot-Savart law may be expressed. Ampere’s circuital law considers an open surface with a boundary (Fig. 4.12). The surface has current passing through it. We consider the boundary to be made up of a number of small line elements. Consider one such element of length dl. We take the value of the tangential component of the magnetic field, Bt, at this element and multiply it by the FIGURE 4.12 117 2024-25  Physics length of that element dl [Note: Btdl=B.d l]. All such products are added together. We consider the limit as the lengths of elements get smaller and their number gets larger. The sum then tends to an integral. Ampere’s law states that this integral is equal to µ0 times the total current passing through the surface, i.e., “ B.dl = µ I0 [4.13(a)] where I is the total current through the surface. The integral is taken over the closed loop coinciding with the boundary C of the surface. The relation above involves a sign-convention, given by the right-hand rule. Let the fingers of the right-hand be curled in the sense the “ boundary is traversed in the loop integral B.dl. Then the direction of the thumb gives the sense in which the Andre Ampere (1775 – current I is regarded as positive. 1836) Andre Marie Ampere was a French physicist, For several applications, a much simplified version of mathematician and chemist Eq. [4.13(a)] proves sufficient. We shall assume that, in who founded the science of such cases, it is possible to choose the loop (called electrodynamics. Ampere an amperian loop) such that at each point of the was a child prodigy loop, either who mastered advanced (i) B is tangential to the loop and is a non-zero constant mathematics by the age of B, or 12. Ampere grasped the significance of Oersted’s (ii) B is normal to the loop, or discovery. He carried out a (iii) B vanishes. large series of experiments Now, let L be the length (part) of the loop for which B to explore the relationship is tangential. Let Ie be the current enclosed by the loop. between current electricity Then, Eq. (4.13) reduces to, and magnetism. These investigations culminated BL =µ0Ie [4.13(b)] ANDRE AMPERE (1775 –1836) in 1827 with the When there is a system with a symmetry such as for publication of the ‘Mathematical Theory of a straight infinite current-carrying wire in Fig. 4.13, the Electrodynamic Pheno- Ampere’s law enables an easy evaluation of the magnetic mena Deduced Solely from field, much the same way Gauss’ law helps in Experiments’. He hypo- determination of the electric field. This is exhibited in the thesised that all magnetic Example 4.8 below. The boundary of the loop chosen is phenomena are due to a circle and magnetic field is tangential to the circulating electric circumference of the circle. The law gives, for the left hand currents. Ampere was side of Eq. [4.13 (b)], B. 2πr. We find that the magnetic humble and absent- field at a distance r outside the wire is tangential and minded. He once forgot an given by invitation to dine with the Emperor Napoleon. He died B × 2πr = µ0 I, of pneumonia at the age of 61. His gravestone bears B = µ0 I/ (2πr) (4.14) the epitaph: Tandem Felix The above result for the infinite wire is interesting (Happy at last). from several points of view. (i) It implies that the field at every point on a circle of radius r, (with the wire along the axis), is same in 118 magnitude. In other words, the magnetic field 2024-25  Moving Charges and Magnetism possesses what is called a cylindrical symmetry. The field that normally can depend on three coordinates depends only on one: r. Whenever there is symmetry, the solutions simplify. (ii) The field direction at any point on this circle is tangential to it. Thus, the lines of constant magnitude of magnetic field form concentric circles. Notice now, in Fig. 4.1(c), the iron filings form concentric circles. These lines called magnetic field lines form closed loops. This is unlike the electrostatic field lines which originate from positive charges and end at negative charges. The expression for the magnetic field of a straight wire provides a theoretical justification to Oersted’s experiments. (iii) Another interesting point to note is that even though the wire is infinite, the field due to it at a non-zero distance is not infinite. It tends to blow up only when we come very close to the wire. The field is directly proportional to the current and inversely proportional to the distance from the (infinitely long) current source. (iv) There exists a simple rule to determine the direction of the magnetic field due to a long wire. This rule, called the right-hand rule*, is: Grasp the wire in your right hand with your extended thumb pointing in the direction of the current. Your fingers will curl around in the direction of the magnetic field. Ampere’s circuital law is not new in content from Biot-Savart law. Both relate the magnetic field and the current, and both express the same physical consequences of a steady electrical current. Ampere’s law is to Biot-Savart law, what Gauss’s law is to Coulomb’s law. Both, Ampere’s and Gauss’s law relate a physical quantity on the periphery or boundary (magnetic or electric field) to another physical quantity, namely, the source, in the interior (current or charge). We also note that Ampere’s circuital law holds for steady currents which do not fluctuate with time. The following example will help us understand what is meant by the term enclosed current. Example 4.7 Figure 4.13 shows a long straight wire of a circular cross-section (radius a) carrying steady current I. The current I is uniformly distributed across this cross-section. Calculate the magnetic field in the region r < a and r > a. EXAMPLE 4.7 FIGURE 4.13 * Note that there are two distinct right-hand rules: One which gives the direction of B on the axis of current-loop and the other which gives direction of B for a straight conducting wire. Fingers and thumb play different roles in the two. 119 2024-25  Physics Solution (a) Consider the case r > a. The Amperian loop, labelled 2, is a circle concentric with the cross-section. For this loop, L =2πr Ie = Current enclosed by the loop = I The result is the familiar expression for a long straight wire B (2π r) = µ0I µ0 I B= [4.15(a)] 2πr 1 B∝ (r > a) r Now the current enclosed I e is not I, but is less than this value. Since the current distribution is uniform, the current enclosed is,  πr2  Ir 2 Ie = I  2 =  πa  a2 I r2 Using Ampere’s law, B (2 π r ) = µ 0 a2  µ I  B =  0 2r [4.15(b)]  2πa  B∝r (r < a) FIGURE 4.14 Figure (4.14) shows a plot of the magnitude of B with distance r EXAMPLE 4.7 from the centre of the wire. The direction of the field is tangential to the respective circular loop (1 or 2) and given by the right-hand rule described earlier in this section. This example possesses the required symmetry so that Ampere’s law can be applied readily. It should be noted that while Ampere’s circuital law holds for any loop, it may not always facilitate an evaluation of the magnetic field in every case. For example, for the case of the circular loop discussed in Section 4.5, it cannot be applied to extract the simple expression B = µ0I/2R [Eq. (4.12)] for the field at the centre of the loop. However, there exists a large number of situations of high symmetry where the law 120 can be conveniently applied. We shall use it in the next section to calculate 2024-25  Moving Charges and Magnetism the magnetic field produced by two commonly used and very useful magnetic systems: the solenoid and the toroid. 4.7 THE SOLENOID We shall discuss a long solenoid. By long solenoid we mean that the solenoid’s length is large compared to its radius. It consists of a long wire wound in the form of a helix where the neighbouring turns are closely spaced. So each turn can be regarded as a circular loop. The net magnetic field is the vector sum of the fields due to all the turns. Enamelled wires are used for winding so that turns are insulated from each other. FIGURE 4.15 (a) The magnetic field due to a section of the solenoid which has been stretched out for clarity. Only the exterior semi-circular part is shown. Notice how the circular loops between neighbouring turns tend to cancel. (b) The magnetic field of a finite solenoid. Figure 4.15 displays the magnetic field lines for a finite solenoid. We show a section of this solenoid in an enlarged manner in Fig. 4.15(a). Figure 4.15(b) shows the entire finite solenoid with its magnetic field. In Fig. 4.15(a), it is clear from the circular loops that the field between two neighbouring turns vanishes. In Fig. 4.15(b), we see that the field at the interior mid-point P is uniform, strong and along the axis of the solenoid. The field at the exterior mid-point Q is weak and moreover is along the axis of the solenoid with no perpendicular or normal component. As the FIGURE 4.16 The magnetic field of a very long solenoid. We consider a rectangular Amperian loop abcd to determine the field. 121 2024-25  Physics solenoid is made longer it appears like a long cylindrical metal sheet. Figure 4.16 represents this idealised picture. The field outside the solenoid approaches zero. We shall assume that the field outside is zero. The field inside becomes everywhere parallel to the axis. Consider a rectangular Amperian loop abcd. Along cd the field is zero as argued above. Along transverse sections bc and ad, the field component is zero. Thus, these two sections make no contribution. Let the field along ab be B. Thus, the relevant length of the Amperian loop is, L = h. Let n be the number of turns per unit length, then the total number of turns is nh. The enclosed current is, Ie = I (n h), where I is the current in the solenoid. From Ampere’s circuital law [Eq. 4.13 (b)] BL = µ0Ie, B h = µ0I (n h) B = µ0 n I (4.16) The direction of the field is given by the right-hand rule. The solenoid is commonly used to obtain a uniform magnetic field. We shall see in the next chapter that a large field is possible by inserting a soft iron core inside the solenoid. Example 4.8 A solenoid of length 0.5 m has a radius of 1 cm and is made up of 500 turns. It carries a current of 5 A. What is the magnitude of the magnetic field inside the solenoid? Solution The number of turns per unit length is, 500 n = = 1000 turns/m EXAMPLE 4.8 0.5 The length l = 0.5 m and radius r = 0.01 m. Thus, l/a = 50 i.e., l >> a. Hence, we can use the long solenoid formula, namely, Eq. (4.20) B = µ0n I = 4π × 10–7 × 103 × 5 = 6.28 × 10–3 T 4.8 FORCE BETWEEN TWO PARALLEL CURRENTS, THE AMPERE We have learnt that there exists a magnetic field due to a conductor carrying a current which obeys the Biot-Savart law. Further, we have learnt that an external magnetic field will exert a force on a current-carrying conductor. This follows from the Lorentz force formula. Thus, it is logical to expect that two current-carrying conductors placed near each other will exert (magnetic) forces on each other. In the period 1820-25, Ampere studied the nature of this FIGURE 4.17 Two long straight magnetic force and its dependence on the magnitude of parallel conductors carrying steady the current, on the shape and size of the conductors, as currents Ia and Ib and separated by a well as, the distances between the conductors. In this distance d. Ba is the magnetic field set up by conductor ‘a’ at conductor ‘b’. section, we shall take the simple example of two parallel current- carrying conductors, which will perhaps help us 122 to appreciate Ampere’s painstaking work. 2024-25  Moving Charges and Magnetism Figure 4.17 shows two long parallel conductors a and b separated by a distance d and carrying (parallel) currents Ia and Ib, respectively. The conductor ‘a’ produces, the same magnetic field Ba at all points along the conductor ‘b’. The right-hand rule tells us that the direction of this field is downwards (when the conductors are placed horizontally). Its magnitude is given by Eq. [4.15(a)] or from Ampere’s circuital law, µ0 I a Ba = 2πd The conductor ‘b’ carrying a current Ib will experience a sideways force due to the field Ba. The direction of this force is towards the conductor ‘a’ (Verify this). We label this force as Fba, the force on a segment L of ‘b’ due to ‘a’. The magnitude of this force is given by Eq. (4.4), Fba = I b LBa µ0 I a I b = L (4.17) 2πd It is of course possible to compute the force on ‘a’ due to ‘b’. From considerations similar to above we can find the force Fab, on a segment of length L of ‘a’ due to the current in ‘b’. It is equal in magnitude to Fba, and directed towards ‘b’. Thus, Fba = –Fab (4.18) Note that this is consistent with Newton’s third Law. Thus, at least for parallel conductors and steady currents, we have shown that the Biot-Savart law and the Lorentz force yield results in accordance with Newton’s third Law*. We have seen from above that currents flowing in the same direction attract each other. One can show that oppositely directed currents repel each other. Thus, Parallel currents attract, and antiparallel currents repel. This rule is the opposite of what we find in electrostatics. Like (same sign) charges repel each other, but like (parallel) currents attract each other. Let fba represent the magnitude of the force Fba per unit length. Then, from Eq. (4.17), µ0 I a I b f ba = (4.19) 2πd The above expression is used to define the ampere (A), which is one of the seven SI base units. * It turns out that when we have time-dependent currents and/or charges in motion, Newton’s third law may not hold for forces between charges and/or conductors. An essential consequence of the Newton’s third law in mechanics is conservation of momentum of an isolated system. This, however, holds even for the case of time-dependent situations with electromagnetic fields, provided 123 the momentum carried by fields is also taken into account. 2024-25  Physics The ampere is the value of that steady current which, when maintained in each of the two very long, straight, parallel conductors of negligible cross-section, and placed one metre apart in vacuum, would produce on each of these conductors a force equal to 2 × 10–7 newtons per metre of length. This definition of the ampere was adopted in 1946. It is a theoretical definition. In practice, one must eliminate the effect of the earth’s magnetic field and substitute very long wires by multiturn coils of appropriate geometries. An instrument called the current balance is used to measure this mechanical force. The SI unit of charge, namely, the coulomb, can now be defined in terms of the ampere. When a steady current of 1A is set up in a conductor, the quantity of charge that flows through its cross-section in 1s is one coulomb (1C). Example 4.9 The horizontal component of the earth’s magnetic field at a certain place is 3.0 ×10–5 T and the direction of the field is from the geographic south to the geographic north. A very long straight conductor is carrying a steady current of 1A. What is the force per unit length on it when it is placed on a horizontal table and the direction of the current is (a) east to west; (b) south to north? Solution F = Il × B F = IlB sinθ The force per unit length is f = F/l = I B sinθ (a) When the current is flowing from east to west, θ = 90° Hence, f=IB = 1 × 3 × 10–5 = 3 × 10–5 N m–1 This is larger than the value 2×10–7 Nm–1 quoted in the definition of the ampere. Hence it is important to eliminate the effect of the earth’s magnetic field and other stray fields while standardising the ampere. EXAMPLE 4.9 The direction of the force is downwards. This direction may be obtained by the directional property of cross product of vectors. (b) When the current is flowing from south to north, θ = 0o f=0 Hence there is no force on the conductor. 4.9 TORQUE ON CURRENT LOOP, MAGNETIC DIPOLE 4.9.1 Torque on a rectangular current loop in a uniform magnetic field We now show that a rectangular loop carrying a steady current I and placed in a uniform magnetic field experiences a torque. It does not experience a net force. This behaviour is analogous to that of electric 124 dipole in a uniform electric field (Section 1.11). 2024-25  Moving Charges and Magnetism We first consider the simple case when the rectangular loop is placed such that the uniform magnetic field B is in the plane of the loop. This is illustrated in Fig. 4.18(a). The field exerts no force on the two arms AD and BC of the loop. It is perpendicular to the arm AB of the loop and exerts a force F1 on it which is directed into the plane of the loop. Its magnitude is, F1 = I b B Similarly, it exerts a force F2 on the arm CD and F2 is directed out of the plane of the paper. F2 = I b B = F1 Thus, the net force on the loop is zero. There is a torque on the loop due to the pair of forces F1 and F2. Figure 4.18(b) shows a view of the loop from the AD end. It shows that the torque on the loop tends to rotate it anticlockwise. This torque is (in magnitude), a a τ = F1 + F2 2 2 a a = IbB + IbB = I (ab ) B 2 2 =IAB (4.20) FIGURE 4.18 (a) A rectangular current-carrying coil in uniform where A = ab is the area of the rectangle. magnetic field. The magnetic moment We next consider the case when the plane of the loop, m points downwards. The torque τ is is not along the magnetic field, but makes an angle with along the axis and tends to rotate the it. We take the angle between the field and the normal to coil anticlockwise. (b) The couple acting on the coil. the coil to be angle θ (The previous case corresponds to θ = π/2). Figure 4.19 illustrates this general case. The forces on the arms BC and DA are equal, opposite, and act along the axis of the coil, which connects the centres of mass of BC and DA. Being collinear along the axis they cancel each other, resulting in no net force or torque. The forces on arms AB and CD are F1 and F2. They too are equal and opposite, with magnitude, F1 = F2 = I b B But they are not collinear! This results in a couple as before. The torque is, however, less than the earlier case when plane of loop was along the magnetic field. This is because the perpendicular distance between the forces of the couple has decreased. Figure 4.19(b) is a view of the arrangement from the AD end and it illustrates these two forces constituting a couple. The magnitude of the torque on the loop is, a a τ = F1 sin θ + F2 sin θ 2 2 = I ab B sin θ = I A B sin θ (4.21) 125 2024-25  Physics As θ à 0, the perpendicular distance between the forces of the couple also approaches zero. This makes the forces collinear and the net force and torque zero. The torques in Eqs. (4.20) and (4.21) can be expressed as vector product of the magnetic moment of the coil and the magnetic field. We define the magnetic moment of the current loop as, m=IA (4.22) where the direction of the area vector A is given by the right-hand thumb rule and is directed into the plane of the paper in Fig. 4.18. Then as the angle between m and B is θ , Eqs. (4.20) and (4.21) can be expressed by one expression (4.23) This is analogous to the electrostatic case (Electric dipole of dipole moment pe in an electric field E). τ = pe × E As is clear from Eq. (4.22), the dimensions of the magnetic moment are [A][L2] and its unit is Am2. FIGURE 4.19 (a) The area vector of the loop From Eq. (4.23), we see that the torque τ ABCD makes an arbitrary angle θ with vanishes when m is either parallel or antiparallel the magnetic field. (b) Top view of to the magnetic field B. This indicates a state of the loop. The forces F1 and F2 acting equilibrium as there is no torque on the coil (this on the arms AB and CD also applies to any object with a magnetic moment are indicated. m). When m and B are parallel the equilibrium is a stable one. Any small rotation of the coil produces a torque which brings it back to its original position. When they are antiparallel, the equilibrium is unstable as any rotation produces a torque which increases with the amount of rotation. The presence of this torque is also the reason why a small magnet or any magnetic dipole aligns itself with the external magnetic field. If the loop has N closely wound turns, the expression for torque, Eq. (4.23), still holds, with m=NIA (4.24) Example 4.10 A 100 turn closely wound circular coil of radius 10 cm carries a current of 3.2 A. (a) What is the field at the centre of the coil? (b) What is the magnetic moment of this coil? The coil is placed in a vertical plane and is free to rotate about a horizontal axis which coincides with its diameter. A uniform magnetic EXAMPLE 4.10 field of 2T in the horizontal direction exists such that initially the axis of the coil is in the direction of the field. The coil rotates through an angle of 90° under the influence of the magnetic field. (c) What are the magnitudes of the torques on the coil in the initial and final position? (d) What is the angular speed acquired by the coil when it has rotated 126 by 90°? The moment of inertia of the coil is 0.1 kg m2. 2024-25  Moving Charges and Magnetism Solution (a) From Eq. (4.12) µ0 NI B= 2R Here, N = 100; I = 3.2 A, and R = 0.1 m. Hence, 4 × 10 −5 × 10 = (using π × 3.2 = 10) 2 × 10 −1 = 2 × 10–3 T The direction is given by the right-hand thumb rule. (b) The magnetic moment is given by Eq. (4.24), m = N I A = N I π r2 = 100 × 3.2 × 3.14 × 10–2 = 10 A m2 The direction is once again given by the right-hand thumb rule. (c) τ = m × B [from Eq. (4.23)] = m B sin θ Initially, θ = 0. Thus, initial torque τi = 0. Finally, θ = π/2 (or 90º). Thus, final torque τf = m B = 10 × 2 = 20 N m. (d) From Newton’s second law, I where I is the moment of inertia of the coil. From chain rule, dω dω dθ d ω = = ω dt dθ dt d θ Using this, I ω dω = m B sin θ dθ Integrating from θ = 0 to θ = π/2, E XAMPLE 4.10 Example 4.11 EXAMPLE 4.11 (a) A current-carrying circular loop lies on a smooth horizontal plane. Can a uniform magnetic field be set up in such a manner that the loop turns around itself (i.e., turns about the vertical axis). (b) A current-carrying circular loop is located in a uniform external magnetic field. If the loop is free to turn, what is its orientation of stable equilibrium? Show that in this orientation, the flux of 127 2024-25  Physics the total field (external field + field produced by the loop) is maximum. (c) A loop of irregular shape carrying current is located in an external magnetic field. If the wire is flexible, why does it change to a circular shape? Solution (a) No, because that would require τ to be in the vertical direction. But τ = I A × B, and since A of the horizontal loop is in the vertical direction, τ would be in the plane of the loop for any B. (b) Orientation of stable equilibrium is one where the area vector A of the loop is in the direction of external magnetic field. In this EXAMPLE 4.11 orientation, the magnetic field produced by the loop is in the same direction as external field, both normal to the plane of the loop, thus giving rise to maximum flux of the total field. (c) It assumes circular shape with its plane normal to the field to maximise flux, since for a given perimeter, a circle encloses greater area than any other shape. 4.9.2 Circular current loop as a magnetic dipole In this section, we shall consider the elementary magnetic element: the current loop. We shall show that the magnetic field (at large distances) due to current in a circular current loop is very similar in behaviour to the electric field of an electric dipole. In Section 4.5, we have evaluated the magnetic field on the axis of a circular loop, of a radius R, carrying a steady current I. The magnitude of this field is [(Eq. (4.11)], µ0 I R 2 B= ( ) 3/2 2 x 2 + R2 and its direction is along the axis and given by the right-hand thumb rule (Fig. 4.10). Here, x is the distance along the axis from the centre of the loop. For x >> R, we may drop the R 2 term in the denominator. Thus, µ0 IR 2 B= 2x 3 Note that the area of the loop A = πR2. Thus, µ0 IA B= 2πx 3 As earlier, we define the magnetic moment m to have a magnitude IA, m = I A. Hence, µ m B≃ 0 3 2πx µ0 2m = [4.25(a)] 4π x 3 The expression of Eq. [4.25(a)] is very similar to an expression obtained earlier for the electric field of a dipole. The similarity may be seen if we 128 substitute, µ0 → 1/ ε 0 2024-25  Moving Charges and Magnetism m → pe (electrostatic dipole) B → E (electrostatic field) We then obtain, 2pe E= 4 π ε0 x 3 which is precisely the field for an electric dipole at a point on its axis. considered in Chapter 1, Section 1.9 [Eq. (1.20)]. It can be shown that the above analogy can be carried further. We had found in Chapter 1 that the electric field on the perpendicular bisector of the dipole is given by [See Eq.(1.21)], pe E≃ 4πε0 x 3 where x is the distance from the dipole. If we replace p à m and µ0 → 1/ ε 0 in the above expression, we obtain the result for B for a point in the plane of the loop at a distance x from the centre. For x >>R, µ m B≃ 0 3; x >> R [4.25(b)] 4π x The results given by Eqs. [4.25(a)] and [4.25(b)] become exact for a point magnetic dipole. The results obtained above can be shown to apply to any planar loop: a planar current loop is equivalent to a magnetic dipole of dipole moment m = I A, which is the analogue of electric dipole moment p. Note, however, a fundamental difference: an electric dipole is built up of two elementary units — the charges (or electric monopoles). In magnetism, a magnetic dipole (or a current loop) is the most elementary element. The equivalent of electric charges, i.e., magnetic monopoles, are not known to exist. We have shown that a current loop (i) produces a magnetic field (see Fig. 4.10) and behaves like a magnetic dipole at large distances, and (ii) is subject to torque like a magnetic needle. This led Ampere to suggest that all magnetism is due to circulating currents. This seems to be partly true and no magnetic monopoles have been seen so far. However, elementary particles such as an electron or a proton also carry an intrinsic magnetic moment, not accounted by circulating currents. 4.10 THE MOVING COIL GALVANOMETER Currents and voltages in circuits have been discussed extensively in Chapters 3. But how do we measure them? How do we claim that current in a circuit is 1.5 A or the voltage drop across a resistor is 1.2 V? Figure 4.20 exhibits a very useful instrument for this purpose: the moving coil galvanometer (MCG). It is a device whose principle can be understood on the basis of our discussion in Section 4.9. The galvanometer consists of a coil, with many turns, free to rotate about a fixed axis (Fig. 4.20), in a uniform radial magnetic field. There is a cylindrical soft iron core which not only makes the field radial but also increases the strength of the magnetic field. When a current flows through the coil, a torque acts on it. This torque is given by Eq. (4.20) to be 129 τ = NI AB 2024-25  Physics where the symbols have their usual meaning. Since the field is radial by design, we have taken sin θ = 1 in the above expression for the torque. The magnetic torque NIAB tends to rotate the coil. A spring Sp provides a counter torque k φ that balances the magnetic torque NIAB; resulting in a steady angular deflection φ. In equilibrium kφ = NI AB where k is the torsional constant of the spring; i.e. the restoring torque per unit twist. The deflection φ is indicated on the scale by a pointer attached to the spring. We have  NAB  φ= I  k  (4.26) The quantity in brackets is a constant for a given galvanometer. The galvanometer can be used in a number of ways. It can be used as a detector to check if a current is FIGURE 4.20 The moving coil flowing in the circuit. We have come across this usage galvanometer. Its elements are in the Wheatstone’s bridge arrangement. In this usage described in the text. Depending on the neutral position of the pointer (when no current is the requirement, this device can be flowing through the galvanometer) is in the middle of used as a current detector or for the scale and not at the left end as shown in Fig.4.20. measuring the value of the current Depending on the direction of the current, the pointer’s (ammeter) or voltage (voltmeter). deflection is either to the right or the left. The galvanometer cannot as such be used as an ammeter to measure the value of the current in a given circuit. This is for two reasons: (i) Galvanometer is a very sensitive device, it gives a full- scale deflection for a current of the order of µA. (ii) For measuring currents, the galvanometer has to be connected in series, and as it has a large resistance, this will change the value of the current in the circuit. To overcome these difficulties, one attaches a small resistance rs, called shunt resistance, in parallel with the galvanometer coil; so that most of the current passes through the shunt. The resistance of this arrangement is, RG rs / (RG + rs ) ≃ rs if RG >> rs If rs has small value, in relation to the resistance of the rest of the circuit Rc, the effect of introducing the measuring instrument is also small and negligible. This arrangement is schematically shown in Fig. 4.21. FIGURE 4.21 The scale of this ammeter is calibrated and then graduated to read off Conversion of a the current value with ease. We define the current sensitivity of the galvanometer (G) to galvanometer as the deflection per unit current. From Eq. (4.26) this an ammeter by the current sensitivity is, introduction of a shunt resistance rs of φ NAB = (4.27) very small value in I k parallel. A convenient way for the manufacturer to increase the sensitivity is to increase the number of turns N. We choose galvanometers having 130 sensitivities of value, required by our experiment. 2024-25  Moving Charges and Magnetism The galvanometer can also be used as a voltmeter to measure the voltage across a given section of the circuit. For this it must be connected in parallel with that section of the circuit. Further, it must draw a very small current, otherwise the voltage measurement will disturb the original set up by an amount which is very large. Usually we like to keep the disturbance due to the measuring device below one per cent. To ensure this, a large resistance R is connected in series with the galvanometer. This arrangement is schematically depicted in Fig.4.22. Note that the resistance of the voltmeter is now, FIGURE 4.22 RG + R ≃ R : large Conversion of a The scale of the voltmeter is calibrated to read off the voltage value galvanometer (G) to a with ease. We define the voltage sensitivity as the deflection per unit voltmeter by the voltage. From Eq. (4.26), introduction of a resistance R of large φ  NAB  I  NAB  1 value in series. =  =  (4.28) V  k V  k R An interesting point to note is that increasing the current sensitivity may not necessarily increase the voltage sensitivity. Let us take Eq. (4.27) which provides a measure of current sensitivity. If N → 2N, i.e., we double the number of turns, then φ φ →2 I I Thus, the current sensitivity doubles. However, the resistance of the galvanometer is also likely to double, since it is proportional to the length of the wire. In Eq. (4.28), N →2N, and R →2R, thus the voltage sensitivity, φ φ → V V remains unchanged. So in general, the modification needed for conversion of a galvanometer to an ammeter will be different from what is needed for converting it into a voltmeter. Example 4.12 In the circuit (Fig. 4.23) the current is to be measured. What is the value of the current if the ammeter shown (a) is a galvanometer with a resistance R G = 60.00 Ω; (b) is a galvanometer described in (a) but converted to an ammeter by a shunt resistance r s = 0.02 Ω; (c) is an ideal ammeter with zero resistance? EXAMPLE 4.12 FIGURE 4.23 131 2024-25  Physics Solution (a) Total resistance in the circuit is, RG + 3 = 63 Ω. Hence, I = 3/63 = 0.048 A. (b) Resistance of the galvanometer converted to an ammeter is, RG rs 60 Ω × 0.02Ω EXAMPLE 4.12 = ≃ 0.02Ω RG + rs (60 + 0.02)Ω Total resistance in the circuit is, 0.02 Ω + 3 Ω = 3.02 Ω. Hence, I = 3/3.02 = 0.99 A. (c) For the ideal ammeter with zero resistance, I = 3/3 = 1.00 A SUMMARY 1. The total force on a charge q moving with velocity v in the presence of magnetic and electric fields B and E, respectively is called the Lorentz force. It is given by the expression: F = q (v × B + E) The magnetic force q (v × B) is normal to v and work done by it is zero. 2. A straight conductor of length l and carrying a steady current I experiences a force F in a uniform external magnetic field B, F=Il×B where|l| = l and the direction of l is given by the direction of the current. 3. In a uniform magnetic field B, a charge q executes a circular orbit in a plane normal to B. Its frequency of uniform circular motion is called the cyclotron frequency and is given by: qB νc = 2 πm This frequency is independent of the particle’s speed and radius. This fact is exploited in a machine, the cyclotron, which is used to accelerate charged particles. 4. The Biot-Savart law asserts that the magnetic field dB due to an element dl carrying a steady current I at a point P at a distance r from the current element is: µ0 dl × r dB = I 4π r3 To obtain the total field at P, we must integrate this vector expression over the entire length of the conductor. 5. The magnitude of the magnetic field due to a circular coil of radius R carrying a current I at an axial distance x from the centre is 132 2024-25  Moving Charges and Magnetism µ0 IR 2 B= 2( x + R 2 )3 / 2 2 At the centre this reduces to µ0 I B= 2R 6. Ampere’s Circuital Law: Let an open surface S be bounded by a loop C. Then the Ampere’s law states that Ñ B.d l = µ I where I refers to ∫ C 0 the current passing through S. The sign of I is determined from the right-hand rule. We have discussed a simplified form of this law. If B is directed along the tangent to every point on the perimeter L of a closed curve and is constant in magnitude along perimeter then, BL = µ0 Ie where Ie is the net current enclosed by the closed circuit. 7. The magnitude of the magnetic field at a distance R from a long, straight wire carrying a current I is given by: µ0 I B= 2πR The field lines are circles concentric with the wire. 8. The magnitude of the field B inside a long solenoid carrying a current I is B = µ0nI where n is the number of turns per unit length. 9. Parallel currents attract and anti-parallel currents repel. 10. A planar loop carrying a current I, having N closely wound turns, and an area A possesses a magnetic moment m where, m=NIA and the direction of m is given by the right-hand thumb rule : curl the palm of your right hand along the loop with the fingers pointing in the direction of the current. The thumb sticking out gives the direction of m (and A) When this loop is placed in a uniform magnetic field B, the force F on it is: F = 0 And the torque on it is, τ=m×B In a moving coil galvanometer, this torque is balanced by a counter- torque due to a spring, yielding kφ = NI AB where φ is the equilibrium deflection and k the torsion constant of the spring. 11. A moving coil galvanometer can be converted into a ammeter by introducing a shunt resistance rs, of small value in parallel. It can be converted into a voltmeter by introducing a resistance of a large value in series. 133 2024-25  Physics Physical Quantity Symbol Nature Dimensions Units Remarks Permeability of free µ0 Scalar [MLT –2A–2] T m A–1 4π × 10–7 T m A–1 space Magnetic Field B Vector [M T –2A–1] T (telsa) Magnetic Moment m Vector [L2A] A m2 or J/T Torsion Constant k Scalar [M L2T –2] N m rad–1 Appears in MCG POINTS TO PONDER 1. Electrostatic field lines originate at a positive charge and terminate at a negative charge or fade at infinity. Magnetic field lines always form closed loops. 2. The discussion in this Chapter holds only for steady currents which do not vary with time. When currents vary with time Newton’s third law is valid only if momentum carried by the electromagnetic field is taken into account. 3. Recall the expression for the Lorentz force, F = q (v × B + E) This velocity dependent force has occupied the attention of some of the greatest scientific thinkers. If one switches to a frame with instantaneous velocity v, the magnetic part of the force vanishes. The motion of the charged particle is then explained by arguing that there exists an appropriate electric field in the new frame. We shall not discuss the details of this mechanism. However, we stress that the resolution of this paradox implies that electricity and magnetism are linked phenomena (electromagnetism) and that the Lorentz force expression does not imply a universal preferred frame of reference in nature. 4. Ampere’s Circuital law is not independent of the Biot-Savart law. It can be derived from the Biot-Savart law. Its relationship to the Biot-Savart law is similar to the relationship between Gauss’s law and Coulomb’s law. EXERCISES 4.1 A circular coil of wire consisting of 100 turns, each of radius 8.0 cm carries a current of 0.40 A. What is the magnitude of the magnetic field B at the centre of the coil? 4.2 A long straight wire carries a current of 35 A. What is the magnitude of the field B at a point 20 cm from the wire? 4.3 A long straight wire in the horizontal plane carries a current of 50 A in north to south direction. Give the magnitude and direction of B 134 at a point 2.5 m east of the wire. 2024-25  Moving Charges and Magnetism 4.4 A horizontal overhead power line carries a current of 90 A in east to west direction. What is the magnitude and direction of the magnetic field due to the current 1.5 m below the line? 4.5 What is the magnitude of magnetic force per unit length on a wire carrying a current of 8 A and making an angle of 30º with the direction of a uniform magnetic field of 0.15 T ? 4.6 A 3.0 cm wire carrying a current of 10 A is placed inside a solenoid perpendicular to its axis. The magnetic field inside the solenoid is given to be 0.27 T. What is the magnetic force on the wire? 4.7 Two long and parallel straight wires A and B carrying currents of 8.0 A and 5.0 A in the same direction are separated by a distance of 4.0 cm. Estimate the force on a 10 cm section of wire A. 4.8 A closely wound solenoid 80 cm long has 5 layers of windings of 400 turns each. The diameter of the solenoid is 1.8 cm. If the current carried is 8.0 A, estimate the magnitude of B inside the solenoid near its centre. 4.9 A square coil of side 10 cm consists of 20 turns and carries a current of 12 A. The coil is suspended vertically and the normal to the plane of the coil makes an angle of 30º with the direction of a uniform horizontal magnetic field of magnitude 0.80 T. What is the magnitude of torque experienced by the coil? 4.10 Two moving coil meters, M1 and M2 have the following particulars: R1 = 10 Ω, N1 = 30, A1 = 3.6 × 10–3 m2, B1 = 0.25 T R2 = 14 Ω, N2 = 42, A2 = 1.8 × 10–3 m2, B2 = 0.50 T (The spring constants are identical for the two meters). Determine the ratio of (a) current sensitivity and (b) voltage sensitivity of M2 and M1. 4.11 In a chamber, a uniform magnetic field of 6.5 G (1 G = 10 –4 T ) is maintained. An electron is shot into the field with a speed of 4.8 × 106 m s–1 normal to the field. Explain why the path of the electron is a circle. Determine the radius of the circular orbit. (e = 1.5 × 10–19 C, me = 9.1×10–31 kg ) 4.12 In Exercise 4.11 obtain the frequency of revolution of the electron in its circular orbit. Does the answer depend on the speed of the electron? Explain. 4.13 (a) A circular coil of 30 turns and radius 8.0 cm carrying a current of 6.0 A is suspended vertically in a uniform horizontal magnetic field of magnitude 1.0 T. The field lines make an angle of 60° with the normal of the coil. Calculate the magnitude of the counter torque that must be applied to prevent the coil from turning. (