Callister Concept Check Answers PDF

Document Details

CoherentNeumann

Uploaded by CoherentNeumann

Ladoke Akintola University of Technology Ogbomoso

Tags

materials science concept checks engineering materials

Summary

This document contains concept checks and answers from a materials science textbook. It covers topics such as atomic weights, electron configurations, and crystal structures.

Full Transcript

1 7 Concept Check 2.1 Question: Why are the atomic weights of the elements generally not integers? Cite two reasons. Answer: The atomic weights of the elements ordinarily are not integers because: (1) the atomic masses of the atoms normally are not integers (except for 12C), and (2)...

1 7 Concept Check 2.1 Question: Why are the atomic weights of the elements generally not integers? Cite two reasons. Answer: The atomic weights of the elements ordinarily are not integers because: (1) the atomic masses of the atoms normally are not integers (except for 12C), and (2) the atomic weight is taken as the weighted average of the atomic masses of an atom's naturally occurring isotopes. 2 3 Concept Check 2.2 Question: Give electron configurations for the Fe3+and S2- ions. Answer: The Fe3+ ion is an iron atom that has lost three electrons. Since the electron configuration of the Fe atom is 1s22s22p63s23p63d64s2 (Table 2.2), the configuration for Fe3+ is 1s22s22p63s23p63d5. The S2- ion a sulfur atom that has gained two electrons. Since the electron configuration of the S atom is 1s22s22p63s23p4 (Table 2.2), the configuration for S2- is 1s22s22p63s23p6. 3 0 Concept Check 2.3 Question: Offer an explanation as to why covalently bonded materials are generally less dense than ionically or metallically bonded ones. Answer: Covalently bonded materials are less dense than metallic or ionically bonded ones because covalent bonds are directional in nature whereas metallic and ionic are not; when bonds are directional, the atoms cannot pack together in as dense a manner, yielding a lower mass density. 4 9 Concept Check 3.1 Question: What is the difference between crystal structure and crystal system? Answer: A crystal structure is described by both the geometry of, and atomic arrangements within, the unit cell, whereas a crystal system is described only in terms of the unit cell geometry. For example, face-centered cubic and body-centered cubic are crystal structures that belong to the cubic crystal system. 6 9 Concept Check 3.2 Question: For cubic crystals, as values of the planar indices h, k, and l increase, does the distance between adjacent and parallel planes (i.e., the interplanar spacing) increase or decrease? Why? Answer: The interplanar spacing between adjacent and parallel planes decreases as the values of h, k, and l increase. As values of the planar indices increase, the magnitude of the denominator in Equation 3.14 increases, with the result that the interplanar spacing (dhkl) decreases. 72 Concept Check 3.3 Question: Do noncrystalline materials display the phenomenon of allotropy (or polymorphism)? Why or why not? Answer: Noncrystalline materials do not display the phenomenon of allotropy; since a noncrystalline material does not have a defined crystal structure, it cannot have more than one crystal structure, which is the definition of allotropy. 9 6 Concept Check 4.1 Question: The surface energy of a single crystal depends on crystallographic orientation. Does this surface energy increase or decrease with an increase in planar density? Why? Answer: The surface energy of a single crystal depends on the planar density (i.e., degree of atomic packing) of the exposed surface plane because of the number of unsatisfied bonds. As the planar density increases, the number of nearest atoms in the plane increases, which results in an increase in the number of satisfied atomic bonds in the plane, and a decrease in the number of unsatisfied bonds. Since the number of unsatisfied bonds diminishes, so also does the surface energy decrease. (That is, surface energy decreases with an increase in planar density.) 103 Concept Check 4.2 Question: Does the grain size number (n of Equation 4.16) increase or decrease with decreasing grain size? Why? Answer: Taking logarithms of Equation 4.16 and then rearranging such that the grain size number n is the dependent variable leads to the expression logN n =1+ log 2 Thus, n increases with increasing N. But as N (the average number of grains per square inch at a ! magnification of 100 times) increases the grain size decreases. In other words, the value of n increases with decreasing grain size. 120 Concept Check 5.1 Question: Rank the magnitudes of the diffusion coefficients from greatest to least for the following systems: N in Fe at 700°C Cr in Fe at 700°C N in Fe at 900°C Cr in Fe at 900°C Now justify this ranking. (Note: Both Fe and Cr have the BCC crystal structure, and the atomic radii for Fe, Cr, and N are 0.124, 0.125, and 0.065 nm, respectively. You may also want to refer to Section 4.3.) Answer: The diffusion coefficient magnitude ranking is as follows: N in Fe at 900°C; DN(900) N in Fe at 700°C; DN(700) Cr in Fe at 900°C; DCr(900) Cr in Fe at 700°C; DCr(700) Nitrogen is an interstitial impurity in Fe (on the basis of its atomic radius), whereas Cr is a substitutional impurity. Since interstitial diffusion occurs more rapidly than substitutional impurity diffusion, DN > DCr. Also, inasmuch as the magnitude of the diffusion coefficient increases with increasing temperature, D(900) > D(700). Concept Check 5.2 Question: Consider the self-diffusion of two hypothetical metals A and B. On a schematic graph of ln D versus 1/T, plot (and label) lines for both metals given that D0(A) > D0(B) and also that Qd(A) > Qd(B). Answer: The schematic ln D versus 1/T plot with lines for metals A and B is shown below. As explained in the previous section, the intercept with the vertical axis is equal to ln D0. As shown in this plot, the intercept for metal A is greater than for metal B inasmuch as D0(A) > D0(B) [alternatively ln D0(A) > ln D0(B)]. In addition, the slope of the line is equal to –Qd/R. The two lines in the plot have been constructed such that negative slope for metal A is greater than for metal B, inasmuch as Qd(A) > Qd(B) 14 5 Concept Check 6.1 Question: Cite the primary differences between elastic, anelastic, and plastic deformation behaviors. Answer: Elastic deformation is time-independent and nonpermanent, anelastic deformation is time-dependent and nonpermanent, while plastic deformation is permanent. 150 Concept Check 6.2 Questions: Of those metals listed in Table 6.3, (a) Which will experience the greatest percent reduction in area? Why? (b) Which is the strongest? Why? (c) Which is the stiffest? Why? Table 6.3 Tensile stress-strain data for several hypothetical metals to be used with Concept Checks 6.2 and 6.4 Yield Tensile Strain Fracture Elastic Strength Strength at Strength Modulus Material (MPa) (MPa) Fracture (MPa) (GPa) A 310 340 0.23 265 210 B 100 120 0.40 105 150 C 415 550 0.15 500 310 D 700 850 0.14 720 210 E Fractures before yielding 650 350 Answers: (d) Material B will experience the greatest percent area reduction since it has the highest strain at fracture, and, therefore is most ductile. (e) Material D is the strongest because it has the highest yield and tensile strengths. (f) Material E is the stiffest because it has the highest elastic modulus. 15 4 Concept Check 6.3 Question: Make a schematic plot showing the tensile engineering stress–strain behavior for a typical metal alloy to the point of fracture. Now superimpose on this plot a schematic compressive engineering stress-strain curve for the same alloy. Explain any differences between the two curves. Answer: The schematic stress-strain graph on which is plotted the two curves is shown below. The initial linear (elastic) portions of both curves will be the same. Otherwise, there are three differences between the two curves which are as follows: (1) Beyond the elastic region, the tension curve lies below the compression one. The reason for this is that, during compression, the cross-sectional area of the specimen is increasing —that is, for two specimens that have the same initial cross-sectional area (A0), at some specific strain value the instantaneous cross-sectional area in compression will be greater than in tension. Consequently, the applied force necessary to continue deformation will be greater for compression than for tension; and, since stress is defined according to Equation 6.1 as F "= A0 ! the applied force is greater for compression, so also will the stress be greater (since A0 is the same for both cases). (2) The compression curve will not display a maximum inasmuch as the specimen tested in compression will not experience necking—the cross-sectional area over which deformation is occurring is continually increasing for compression. (3) The strain at which failure occurs will be greater for compression. Again, this behavior is explained by the lack of necking for the specimen tested in compression. 16 0 Concept Check 6.4 Question: Of those metals listed in Table 6.3, which is the hardest? Why? Answer: Material D is the hardest because it has the highest tensile strength. 18 1 Concept Check 7.1 Question: Which of the following is the slip system for the simple cubic crystal structure? Why? {100} {110} {100} {110} (Note: a unit cell for the simple cubic crystal structure is shown in Figure 3.23.) Answer: The slip system for some crystal structure corresponds to the most densely packed crystallographic plane, and, in that plane, the most closely packed crystallographic direction. For simple cubic, the most densely packed atomic plane is the {100} type plane; the most densely packed direction within this plane is an type direction. Therefore, the slip system for simple cubic is {100}. 18 3 Concept Check 7.2 Question: Explain the difference between resolved shear stress and critical resolved shear stress. Answer: Resolved shear stress is the shear component of an applied tensile (or compressive) stress resolved along a slip plane that is other than perpendicular or parallel to the stress axis. The critical resolved shear stress is the value of resolved shear stress at which yielding begins; it is a property of the material. 193 Concept Check 7.3 Question: When making hardness measurements, what will be the effect of making an indentation very close to a preexisting indentation? Why? Answer: The hardness measured from an indentation that is positioned very close to a preexisting indentation will be high. The material in this vicinity was cold-worked when the first indentation was made. 19 4 Concept Check 7.4 Question: Would you expect a crystalline ceramic material to strain harden at room temperature? Why or why not? Answer: No, it would not be expected. In order for a material to strain harden it must be plastically deformed; since ceramic materials are brittle at room temperature, they will fracture before any plastic deformation takes place. 19 8 Concept Check 7.5 Question: Briefly explain why some metals (e.g., lead and tin) do not strain harden when deformed at room temperature. Answer: Metals such as lead and tin do not strain harden at room temperature because their recrystallization temperatures lie below room temperature (Table 7.2). 19 9 Concept Check 7.6 Question: Would you expect it to be possible for ceramic materials to experience recrystallization? Why or why not? Answer: No, recrystallization is not expected in ceramic materials. In order to experience recrystallization, a material must first be plastically deformed, and ceramic materials are too brittle to be plastically deformed. 20 8 Concept Check 8.1 Question: Cite two situations in which the possibility of failure is part of the design of a component or product. Answer: Several situations in which the possibility of failure is part of the design of a component or product are as follows: (1) the pull tab on the top of aluminum beverage cans; (2) aluminum utility/light poles that reside along freeways—a minimum of damage occurs to a vehicle when it collides with the pole; and (3) in some machinery components, a shear pin is used to connect a gear or pulley to a shaft—the pin is designed shear off before damage is done to either the shaft or gear in an overload situation. 229 Concept Check 8.2 Question: Make a schematic sketch of a stress-versus-time plot for the situation when the stress ratio R has a value of +1. Answer: For a stress ratio (R) of +1, then, from Equation 8.17, σ = σ max min This is to say that the stress remains constant (or does not fluctuate) with time, or the stress- versus-time plot would appear as Concept Check 8.3 Question: Using Equations 8.16 and 8.17, demonstrate that increasing the value of the stress ratio R produces a decrease in stress amplitude σa. Answer: From Equation 8.17 " min =R" max Furthermore, Equation 8.16 is ! "a max min 2 ! Substitution of σ from the former expression into the latter gives " #R" " "a = = ( 1R)# ma x ma x max 22 Therefore, as the magnitude of R increases (or becomes more positive) the magnitude of σa ! decreases. 23 4 Concept Check 8.4 Question: Surfaces for some steel specimens that have failed by fatigue have a bright crystalline or grainy appearance. Laymen may explain the failure by saying that the metal crystallized while in service. Offer a criticism for this explanation. Answer: To crystallize means to become crystalline. Thus, the statement "The metal fractured because it crystallized" is erroneous inasmuch as the metal was crystalline prior to being stressed (virtually all metals are crystalline). 239 Concept Check 8.5 Question: Superimpose on the same strain-versus-time plot schematic creep curves for both constant tensile stress and constant tensile load, and explain the differences in behavior. Answer: Schematic creep curves at both constant stress and constant load are shown below. With increasing time, the constant load curve becomes progressively higher than the constant stress curve. Since these tests are tensile ones, the cross-sectional area diminishes as deformation progresses. Thus, in order to maintain a constant stress, the applied load must correspondingly be diminished since stress = load/area. 25 6 Concept Check 9.1 Question: What is the difference between the states of phase equilibrium and metastability? Answer: For the condition of phase equilibrium the free energy is a minimum, the system is completely stable meaning that over time the phase characteristics are constant. For metastability, the system is not at equilibrium, and there are very slight (and often imperceptible) changes of the phase characteristics with time. 26 3 Concept Check 9.2 Question: A copper-nickel alloy of composition 70 wt% Ni-30 wt% Cu is slowly heated from a temperature of 1300°C. (g) At what temperature does the first liquid phase form? (h) What is the composition of this liquid phase? (i) At what temperature does complete melting of the alloy occur? (j) What is the composition of the last solid remaining prior to complete melting? Solution: Upon heating a copper-nickel alloy of composition 70 wt% Ni-30 wt% Cu from 1300°C and utilizing Figure 9.3a: (k) The first liquid forms at the temperature at which a vertical line at this composition intersects the α-(α + L) phase boundary—i.e., about 1350°C; (l) The composition of this liquid phase corresponds to the intersection with the (α + L)- L phase boundary, of a tie line constructed across the α + L phase region at 1350°C— i.e., 59 wt% Ni; (m) Complete melting of the alloy occurs at the intersection of this same vertical line at 70 wt% Ni with the (α + L)-L phase boundary—i.e., about 1380°C; (n) The composition of the last solid remaining prior to complete melting corresponds to the intersection with α-(α + L) phase boundary, of the tie line constructed across the α + L phase region at 1380°C—i.e., about 78 wt% Ni. Concept Check 9.3 Question: Is it possible to have a copper-nickel alloy that, at equilibrium, consists of an α phase of composition 37 wt% Ni-63 wt% Cu, and also a liquid phase of composition 20 wt% Ag- 80 wt% Cu? If so, what will be the approximate temperature of the alloy? If this is not possible, explain why. Answer: It is not possible to have a Cu-Ni alloy, which at equilibrium, consists of a liquid phase of composition 20 wt% Ni-80 wt% Cu and an α phase of composition 37 wt% Ni-63 wt% Cu. From Figure 9.3a, a single tie line does not exist within the α + L region that intersects the phase boundaries at the given compositions. At 20 wt% Ni, the L-(α + L) phase boundary is at about 1200°C, whereas at 37 wt% Ni the (L + α)-α phase boundary is at about 1225°C. 272 Concept Check 9.4 Question: At 700°C (1290°F), what is the maximum solubility (a) of Cu in Ag? (b) Of Ag in Cu? Answer: (a) From the copper-silver phase diagram, Figure 9.7, the maximum solubility of Cu in Ag at 700°C corresponds to the position of the β-(α + β) phase boundary at this temperature, or to about 6 wt% Cu. (b) From this same figure, the maximum solubility of Ag in Cu corresponds to the position of the α-(α + β) phase boundary at this temperature, or about 5 wt% Ag. Concept Check 9.5 Question: Below is a portion of the H2O-NaCl phase diagram: (o) Using this diagram, briefly explain how spreading salt on ice that is at a temperature below 0°C (32°F) can cause the ice to melt. (p) At what temperature is salt no longer useful in causing ice to melt? Solution: (a) Spreading salt on ice will lower the melting temperature, since the liquidus line decreases from 0°C (at 100% H20) to the eutectic temperature at about -21°C (23 wt% NaCl). Thus, ice at a temperature below 0°C (and above -21°C) can be made to form a liquid phase by the addition of salt. (b) At -21°C and below ice is no longer useful in causing ice to melt because this is the lowest temperature at which a liquid phase forms (i.e., it is the eutectic temperature for this system). 286 Concept Check 9.6 Question: The figure below is the hafnium-vanadium phase diagram, for which only single-phase regions are labeled. Specify temperature-composition points at which all eutectics, eutectoids, peritectics, and congruent phase transformations occur. Also, for each, write the reaction upon cooling. Answer: There are two eutectics on this phase diagram. One exists at 18 wt% V-82 wt % Hf and 1455°C. The reaction upon cooling is L (3Hf + HfV2 The other eutectic exists at 39 wt% V-61 wt% Hf and 1520°C. This reaction upon cooling is L HfV2 + V(solid solution) There is one eutectoid at 6 wt% V-94 wt% Hf and 1190°C. Its reaction upon cooling is (3Hf -> aHf + HfV2 There is one congruent melting point at 36 wt% V-64 wt% Hf and 1550°C. The reaction ! upon cooling is L -> HfV2 No peritectics are present. 28 9 Concept Check 9.7 Question: For a ternary system, three components are present; temperature is also a variable. What is the maximum number of phases that may be present for a ternary system, assuming that pressure is held constant? Answer: For a ternary system (C = 3) at constant pressure (N = 1), Gibbs phase rule, Equation 9.16, becomes P+F=C+N=3+1=4 Or, P=4–F Thus, when F = 0, P will have its maximum value of 4, which means that the maximum number of phases present for this situation is 4. 29 9 Concept Check 9.8 Question: Briefly explain why a proeutectoid phase (ferrite or cementite) forms along austenite grain boundaries. Hint: Consult Section 4.6. Answer: Associated with grain boundaries is an interfacial energy (i.e., grain boundary energy—Section 4.6). A lower net interfacial energy increase results when a proeutectoid phase forms along existing austenite grain boundaries than when the proeutectoid phase forms within the interior of the grains. 33 0 Concept Check 10.1 Question: Which is the more stable, the pearlitic or the spheroiditic microstructure? Why? Answer: Spheroiditic microstructures are more stable than pearlitic ones. Since pearlite transforms to spheroidite, the latter is more stable 33 2 Concept Check 10.2 Question: Cite two major differences between martensitic and pearlitic transformations. Answer: Two major differences are: 1) atomic diffusion is necessary for the pearlitic transformation, whereas the martensitic transformation is diffusionless; and 2) relative to transformation rate, the martensitic transformation is virtually instantaneous, while the pearlitic transformation is time-dependent. 335 Concept Check 10.3 Question: Make a copy of the isothermal transformation diagram for an iron-carbon alloy of eutectoid composition (Figure 10.22) and then sketch and label on this diagram a time- temperature path that will produce 100% fine pearlite. Answer: Below is shown an isothermal transformation diagram for a eutectoid iron- carbon alloy on which is included a time-temperature path that will produce 100% fine pearlite. 33 9 Concept Check 10.4 Question: Briefly describe the simplest continuous cooling heat treatment procedure that would be used to convert a 4340 steel from (martensite + bainite) to (ferrite + pearlite). Solution: In order to convert from (martensite + bainite) to (ferrite + pearlite) it is necessary to heat above about 720°C, allow complete austenitization, then cool to room temperature at a rate equal to or less than 0.006°C/s (Figure 10.28). 343 Concept Check 10.5 Question: Rank the following iron-carbon alloys and associated microstructures from the highest to the lowest tensile strength: 0.25 wt%C with spheroidite 0.25 wt%C with coarse pearlite 0.6 wt%C with fine pearlite, and 0.6 wt%C with coarse pearlite. Justify this ranking. Answer: This ranking called for is as follows: (1) 0.6 wt%C with fine pearlite (q) 0.6 wt%C with coarse pearlite (r) 0.25 wt%C with coarse pearlite (s) 0.25 wt%C with spheroidite The 0.25 wt% C, coarse pearlite is stronger than the 0.25 wt% C, spheroidite since coarse pearlite is stronger than spheroidite; the composition of the alloys is the same. The 0.6 wt% C, coarse pearlite is stronger than the 0.25 wt% C, coarse pearlite, since increasing the carbon content increases the strength (while maintained the same coarse pearlite microstructure). Finally, the 0.6 wt% C, fine pearlite is stronger than the 0.6 wt% C, coarse pearlite inasmuch as the strength of fine pearlite is greater than coarse pearlite because of the many more ferrite-cementite phase boundaries in fine pearlite. Concept Check 10.6 Question: For a eutectoid steel, describe an isothermal heat treatment that would be required to produce a specimen having a hardness of 93 HRB. Answer: From Figure 10.30(a), in order for a 0.76 wt% C alloy to have a Rockwell hardness of 93 HRB, the microstructure must be coarse pearlite. Thus, utilizing the isothermal transformation diagram for this alloy, Figure 10.22, after austenitizing at about 760°C, rapidly cool to a temperature at which coarse pearlite forms (i.e., to about 675°C), and allow the specimen to isothermally and completely transform to coarse pearlite. At this temperature an isothermal heat treatment for at least 200 s is required. Then cool to room temperature (cooling rate is not important). 345 Concept Check 10.7 Question: A steel alloy is quenched from a temperature within the austenite phase region into water at room temperature so as to form martensite; the alloy is subsequently tempered at an elevated temperature which is held constant. (t) Make a schematic plot showing how room-temperature ductility varies with the logarithm of tempering time at the elevated temperature. (Be sure to label your axes.) (u) Superimpose and label on this same plot the room-temperature behavior resulting from tempering at a higher tempering temperature and briefly explain the difference in behavior between these two temperatures. Answer: (a) Shown below is the plot that was requested. (b) The line for the higher temperature (labeled TH) will lie above the one at the lower temperature (labeled TL) because the Fe3C particles in tempered martensite will grow faster at the higher temperature; thus, at some given tempering time they will be larger at the higher temperature. The alloy tempered at the higher temperature will be more ductile because there will be fewer α-Fe3C phase boundaries (due to the larger Fe3C particles) that may impede dislocation motion. 36 6 Concept Check 11.1 Question: Briefly explain why ferritic and austenitic stainless steels are not heat treatable. Hint: you may want to consult the first portion of Section 11.3. Answer: Ferritic and austenitic stainless steels are not heat treatable since "heat treatable" is taken to mean that martensite may be made to form with relative ease upon quenching austenite from an elevated temperature. For ferritic stainless steels, austenite does not form upon heating, and, therefore, the austenite-to-martensite transformation is not possible. For austenitic stainless steels, the austenite phase field extends to such low temperatures that the martensitic transformation does not occur. 37 1 Concept Check 11.2 Question: It is possible to produce cast irons that consist of a martensite matrix in which graphite is embedded in either flake, nodule, or rosette form. Briefly describe the treatment necessary to produce each of these three microstructures. Answer: For graphite flakes, gray cast iron is formed (as described in Section 11.2), which is then heated to a temperature at which the ferrite transforms to austenite; the austenite is then rapidly quenched, which transforms to martensite. For graphite nodules and rosettes, nodular and malleable cast irons are first formed (again as described in Section 11.2), which are then austenitized and rapidly quenched. 374 Concept Check 11.3 Question: What is the main difference between a brass and a bronze? Answer: Both brasses and bronzes are copper-based alloys. For brasses, the principal alloying element is zinc, whereas the bronzes are alloyed with other elements such as tin, aluminum, silicon, or nickel. 37 5 Concept Check 11.4 Question: Explain why, under some circumstances, it is not advisable to weld a structure that is fabricated with a 3003 aluminum alloy. Hint: you may want to consult Section 7.12. Answer: Strengthening of a 3003 aluminum alloy is accomplished by cold working. Welding a structure of a cold-worked 3003 alloy will cause it to experience recrystallization, and a resultant loss of strength. 37 7 Concept Check 11.5 Question: On the basis of melting temperature, oxidation resistance, yield strength, and degree of brittleness, discuss whether it would be advisable to hot work or to cold work (a) aluminum alloys, and (b) magnesium alloys. Hint: you may want to consult Sections 7.10 and 7.12. Answer: Most aluminum alloys may be cold-worked since they are ductile and have relatively low yield strengths. Magnesium alloys are normally hot-worked inasmuch as they are quite brittle at room temperature. Also, magnesium alloys have relatively low recrystallization temperatures. 38 6 Concept Check 11.6 Question: (a) Cite two advantages of powder metallurgy over casting. (b) Cite two disadvantages. Answer: (a) Advantages of powder metallurgy over casting are as follows: (v) It is used for alloys having high melting temperatures. (w) Better dimensional tolerances result. 3) Porosity may be introduced, the degree of which may be controlled (which is desirable in some applications such as self-lubricating bearings). (b) The disadvantages of powder metallurgy over casting are as follows: (x) Production of the powder is expensive. (y) Heat treatment after compaction is necessary. 387 Concept Check 11.7 Question: What are the principal differences between welding, brazing, and soldering? You may need to consult another reference. Answer: For welding, there is melting of the pieces to be joined in the vicinity of the bond; a filler material may or may not be used. For brazing, a filler material is used which has a melting temperature in excess of about 425°C (800°F); the filler material is melted, whereas the pieces to be joined are not melted. For soldering, a filler material is used which has a melting temperature less than about 425°C (800°F); the filler material is melted, whereas the pieces to be joined are not. 39 7 Concept Check 11.8 Question: Name the three factors that influence the degree to which martensite is formed throughout the cross section of a steel specimen. For each, tell how the extent of martensite formation may be increased. Answer: The three factors that influence the degree to which martensite is formed are as follows: 1) Alloying elements; adding alloying elements increases the extent to which martensite forms. 2) Specimen size and shape; the extent of martensite formation increases as the specimen cross-section decreases and as the degree of shape irregularity increases. 3) Quenching medium; the more severe the quench, the more martensite is formed. Water provides a more severe quench than does oil, which is followed by air. Agitating the medium also enhances the severity of quench. 407 Concept Check 11.9 Question: Is it possible to produce a precipitation hardened 2014 aluminum alloy having a minimum yield strength of 350 MPa (50,000 psi) and a ductility of at least 18%EL? If so, specify the precipitation heat treatment. If it is not possible then explain why. Answer: In order to answer this question it is necessary to consult Figures 11.27(a) and 11.27(b). Below are tabulated the times required at the various temperatures to achieve the stipulated yield strength. Temperature (°C) Time Range (h) 260 not possible 204 0.3-10 149 9-600 121 >300 With regard to temperatures and times to give the desired 18% EL ductility [Figure 11.27(b)]: Temperature (°C) Time Range (h) 260 not possible 204

Use Quizgecko on...
Browser
Browser