AVIA-1038 Week 1 Day 1 PDF - Fanshawe

Learning Objectives Week 1 Day 1 Tubing Materials & Identification Fabrication Cutting, Bending, Flaring Flareless Fittings Beading Fluid Line Identification 1 AVIA-1038D1 2  General...

Learning Objectives Week 1 Day 1 Tubing Materials & Identification Fabrication Cutting, Bending, Flaring Flareless Fittings Beading Fluid Line Identification 1 AVIA-1038D1 2  General 9-2 Copper  In the early days of aviation, copper tubing was used extensively in aviation fluid applications.  In modern aircraft, aluminum alloy, corrosion resistant steel or titanium tubing have generally replaced copper tubing. 3  General 9-2 Aluminum Alloy Tubing  Tubing made from 1100 H14 (1/2-hard) or 3003 H14 (1/2- hard) is used for general purpose lines of low or negligible fluid pressures, such as instrument lines and ventilating conduits.  Tubing made from 2024-T3, 5052-O, and 6061-T6 aluminum alloy materials is used in general purpose systems of low and medium pressures, such as hydraulic and pneumatic 1,000 to 1,500 psi systems, and fuel and oil lines. 4  General 9-2 Steel  Corrosion resistant steel tubing, either annealed CRES 304, CRES 321 or CRES 304-1/8-hard, is used extensively in high pressure hydraulic systems (3,000 psi or more) for the operation of landing gear, flaps, brakes, and in fire zones.  Its higher tensile strength permits the use of tubing with thinner walls; consequently, the final installation weight is not much greater than that of the thicker wall aluminum alloy tubing. 5  General 9-2 Steel  Steel lines are used where there is a risk of foreign object damage (FOD); i.e., the landing gear and wheel well areas.  Although identification markings for steel tubing differ, each usually includes the manufacturer’s name or trademark, the Society of Automotive Engineers (SAE) number, and the physical condition of the metal. 6  General 9-2 Titanium 3AL-2.5V  This type of tubing and fitting is used extensively in transport category and high-performance aircraft hydraulic systems for pressures above 1,500 psi.  Titanium is 30 percent stronger than steel and 50 percent lighter than steel.  Cryofit fittings or swaged fittings are used with titanium tubing. 7  General 9-2 Titanium 3AL-2.5V  Do not use titanium tubing and fittings in any oxygen system assembly.  Titanium and titanium alloys are oxygen reactive.  If a freshly formed titanium surface is exposed in gaseous oxygen, spontaneous combustion could occur at low pressures. 8  General 9-2 Material Identification  Before making repairs to any aircraft tubing, it is important to make accurate identification of tubing materials.  Aluminum alloy, steel, or titanium tubing can be identified readily by sight where it is used as the basic tubing material.  However, it is difficult to determine whether a material is carbon steel or stainless steel, or whether it is 1100, 3003, 5052-O, 6061-T6 or 2024-T3 aluminum alloy. 9  General 9-2 Material Identification  To positively identify the material used in the original installation, compare code markings of the replacement tubing with the original markings on the tubing being replaced.  On large aluminum alloy tubing, the alloy designation is stamped on the surface.  On small aluminum tubing, the designation may be stamped on the surface; but more often it is shown by a color code, not more than 4" in width, painted at the two ends and approximately midway between the ends of some tubing. 10  General 9-2 Material Identification  When the band consists of two colors, one-half the width is used for each color. [Figure 9-11].  If the code markings are hard or impossible to read, it may be necessary to test samples of the material for hardness-by-hardness testing. 11  General 9-2 Material Identification  Figure 9-1 12  General 9-2 Sizes  Metal tubing is sized by outside diameter (o.d.), which is measured fractionally in sixteenths of an inch.  Thus, number 6 tubing is 6/16" (or 3⁄8") and number 8 tubing is 8/16" (or 1⁄2"), and so forth.  The tube diameter is typically printed on all rigid tubing.  In addition to other classifications or means of identification, tubing is manufactured in various wall thicknesses. 13  General 9-2 Sizes  Thus, it is important when installing tubing to know not only the material and outside diameter, but also the thickness of the wall.  The wall thickness is typically printed on the tubing in thousands of an inch.  To determine the inside diameter (i.d.) of the tube, subtract twice the wall thickness from the outside diameter.  For example, a number 10 piece of tubing with a wall thickness of 0.063" has an inside diameter of 0.625" – 2(0.063") = 0.499". 14 AVIA-1038D1 15  General 9-2 Fabrication of Metal Tube Lines  Damaged tubing and fluid lines should be repaired with new parts whenever possible.  Unfortunately, sometimes replacement is impractical, and repair is necessary.  Scratches, abrasions, or minor corrosion on the outside of fluid lines may be considered negligible and can be smoothed out with a burnishing tool or aluminum wool. 16  General 9-3 Fabrication of Metal Tube Lines  Limitations on the amount of damage that can be repaired in this manner are discussed in this chapter under “Rigid Tubing Inspection and Repair.” If a fluid line assembly is to be replaced, the fittings can often be salvaged; then the repair will involve only tube forming and replacement.  Tube forming consists of four processes: Cutting, bending, flaring, and beading. 17  General 9-3 Fabrication of Metal Tube Lines  If the tubing is small and made of soft material, the assembly can be formed by hand bending during installation.  If the tube is 1⁄4" diameter or larger, hand bending without the aid of tools is impractical. 18  General 9-3 Tube Cutting  When cutting tubing, it is important to produce a square end, free of burrs.  Tubing may be cut with a tube cutter or a hacksaw.  The cutter can be used with any soft metal tubing, such as copper, aluminum, or aluminum alloy.  Correct use of the tube cutter is shown in Figure 9-2.  Special chipless cutters are available for cutting aluminum 6061-T6, corrosion resistant steel and titanium tubing. 19  General 9-3 Tube Cutting  Figure 9-2 20  General 9-3 Tube Cutting  A new piece of tubing should be cut approximately 10 percent longer than the tube to be replaced to provide for minor variations in bending.  Place the tubing in the cutting tool, with the cutting wheel at the point where the cut is to be made.  Rotate the cutter around the tubing, applying a light pressure to the cutting wheel by intermittently twisting the thumbscrew. 21  General 9-3 Tube Cutting  Too much pressure on the cutting wheel at one time could deform the tubing or cause excessive burring.  After cutting the tubing, carefully remove any burrs from inside and outside the tube.  Use a knife or the burring edge attached to the tube cutter.  The deburring operation can be accomplished by the use of a deburring tool as shown in Figure 9-3. 22  General 9-3 Tube Cutting  Figure 9-3 23  General 9-3 Tube Cutting  This tool is capable of removing both the inside and outside burrs by just turning the tool end for end.  When performing the deburring operation, use extreme care that the wall thickness of the end of the tubing is not reduced or fractured.  Very slight damage of this type can lead to fractured flares or defective flares which will not seal properly.  Use a fine-tooth file to file the end square and smooth. 24  General 9-2 Tube Cutting  If a tube cutter is not available, or if tubing of hard material is to be cut, use a fine-tooth hacksaw, preferably one having 32 teeth per inch.  The use of a saw will decrease the amount of work hardening of the tubing during the cutting operation.  After sawing, file the end of the tube square and smooth, removing all burrs.  An easy way to hold small diameter tubing, when cutting it, is to place the tube in a combination flaring tool and clamp the tool in a vise. 25  General 9-3 Tube Cutting  Make the cut about one half inch from the flaring tool.  This procedure keeps sawing vibrations to a minimum and prevents damage to the tubing if it is accidentally hit with the hacksaw frame or file handle while cutting.  Be sure all filings and cuttings are removed from the tube. 26  General 9-3 Tube Bending  The objective in tube bending is to obtain a smooth bend without flattening the tube.  Tubing under 1⁄4" in diameter usually can be bent without the use of a bending tool.  For larger sizes, either portable hand benders or production benders are usually used.  Table 9-4 shows preferred methods and standard bend radii for bending tubing by tube size. 27  General 9-4 Tube Bending  Table 9-4 28  General 9-3 Tube Bending  Using a hand bender, insert the tubing into the groove of the bender, so that the measured end is left of the form block.  Align the two zeros and align the mark on the tubing with the L on the form handle.  If the measured end is on the right side, then align the mark on the tubing with the R on the form handle.  With a steady motion, pull the form handle till the zero mark on the form handle lines up with the desired angle of bend, as indicated on the radius block. [Figure 9-5] 29  General 9-4 Tube Bending  Bend the tubing carefully to avoid excessive flattening, kinking, or wrinkling.  A small amount of flattening in bends is acceptable, but the small diameter of the flattened portion must not be less than 75 percent of the original outside diameter.  Tubing with flattened, wrinkled, or irregular bends should not be installed.  Wrinkled bends usually result from trying to bend thin wall tubing without using a tube bender. 30  General 9-4 Tube Bending  Figure 9-5 31  General 9-4 Tube Bending  Excessive flattening will cause fatigue failure of the tube.  Examples of correct and incorrect tubing bends are shown in Figure 9-8.  Tube bending machines for all types of tubing are generally used in repair stations and large maintenance shops.  With such equipment, proper bends can be made on large diameter tubing and on tubing made from hard material. 32  General 9-5 Tube Bending  Figure 9-8 33  General 9-4 Tube Bending  The production CNC™ tube bender is an example of this type of machine. [Figure 9-9]  The ordinary production tube bender will accommodate tubing ranging from 1⁄4" to 1 1⁄2" outside diameter.  Benders for larger sizes are available, and the principle of their operation is similar to that of the hand tube bender.  The radius blocks are so constructed that the radius of bend will vary with the tube diameter.  The radius of bend is usually stamped on the block. 34  General 9-5 Tube Bending  Figure 9-9 35  General 9-5 Alternative Bending Methods  When hand or production tube benders are not available or are not suitable for a particular bending operation, a filler of metallic composition or of dry sand may be used to facilitate bending.  When using this method, cut the tube slightly longer than is required.  The extra length is for inserting a plug (which may be wooden) in each end.  The tube can also be closed by flattening the ends or by soldering metal disks in them. 36  General 9-5 Alternative Bending Methods  After plugging one end, fill and pack the tube with fine, dry sand and plug tightly.  Both plugs must be tight so they will not be forced out when the bend is made.  After the ends are closed, bend the tubing over a forming block shaped to the specified radius.  In a modified version of the filler method, a fusible alloy is used instead of sand.  In this method, the tube is filled under hot water with a fusible alloy that melts at 160°F. 37  General 9-5 Alternative Bending Methods  The alloy-filled tubing is then removed from the water, allowed to cool, and bent slowly by hand around a forming block or with a tube bender.  After the bend is made, the alloy is again melted under hot water and removed from the tubing.  When using either filler methods, make certain that all particles of the filler are removed.  Visually inspect with a borescope to make certain that no particles will be carried into the system in which the tubing is installed. 38  General 9-5 Alternative Bending Methods  Store the fusible alloy filler where it will be free from dust or dirt.  It can be remelted and reused as often as desired.  Never heat this filler in any other way than the prescribed method, as the alloy will stick to the inside of the tubing, making them both unusable. 39  General 9-5 Tube Flaring  Two kinds of flares are generally used in aircraft tubing: the single flare and the double flare.  [Figure 9-10A and B] Flares are frequently subjected to extremely high pressures; therefore, the flare on the tubing must be properly shaped or the connection will leak or fail.  A flare made too small produces a weak joint, which may leak or pull apart; if made too large, it interferes with the proper engagement of the screw thread on the fitting and will cause leakage. 40  General 9-5 Tube Flaring  Figure 9-10 41  General 9-5 Tube Flaring  Figure 9-10 42  General 9-5 Tube Flaring  A crooked flare is the result of the tubing not being cut squarely.  If a flare is not made properly, flaws cannot be corrected by applying additional torque when tightening the fitting.  The flare and tubing must be free from cracks, dents, nicks, scratches, or any other defects.  The flaring tool used for aircraft tubing has male and female dies ground to produce a flare of 35° to 37°. 43  General 9-5 Tube Flaring  Under no circumstance is it permissible to use an automotive-type flaring tool which produces a flare of 45°. [Figure 9-11].  The single-flare hand flaring tool, similar to that shown in Figure 9-12, is used for flaring tubing.  The tool consists of a flaring block or grip die, a yoke, and a flaring pin.  The flaring block is a hinged double bar with holes corresponding to various sizes of tubing. 44  General 9-6 Tube Flaring  Figure 9-11 45  General 9-6 Tube Flaring  Figure 9-12 46  General 9-5 Tube Flaring  These holes are countersunk on one end to form the outside support against which the flare is formed.  The yoke is used to center the flaring pin over the end of the tube to be flared.  Two types of flaring tools are used to make flares on tubing: the impact type and the rolling type. 47  General 9-6 Instructions for Rolling-Type Flaring Tools  Use these tools only to flare soft copper, aluminum, and brass tubing.  Do not use with corrosion resistant steel or titanium.  Cut the tube squarely and remove all burrs.  Slip the fitting nut and sleeve on the tube.  Loosen clamping screw used for locking the sliding segment in the die holder.  This will permit their separation. 48  General 9-6 Instructions for Rolling-Type Flaring Tools  The tools are self-gauging; the proper size flare is produced when tubing is clamped flush with the top of the die block.  Insert tubing between the segments of the die block that correspond to the size of the tubing to be flared.  Advance the clamp screw against the end segment and tighten firmly.  Move the yoke down over the top of the die holder and twist it clockwise to lock it into position. 49  General 9-6 Instructions for Rolling-Type Flaring Tools  Turn the feed screw down firmly and continue until a slight resistance is felt.  This indicates an accurate flare has been completed.  Always read the tool manufacturer’s instructions, because there are several different types of rolling-type flaring tools that use slightly different procedures. 50  General 9-6 Double Flaring  A double flare is used on soft aluminum alloy tubing 3⁄8" outside diameter and under.  This is necessary to prevent cutting off the flare and failure of the tube assembly under operating pressures.  A double flare is smoother and more concentric than a single flare and therefore seals better.  It is also more resistant to the shearing effect of torque. 51  General 9-7 Double Flaring Instructions  Deburr both the inside and outside of the tubing to be flared.  Cut off the end of the tubing, if it appears damaged.  Anneal brass, copper, and aluminum by heating to a dull red and cool rapidly in cold water.  Open the flaring tool by unscrewing both clamping screws.  Select the hole in the flaring bar that matches the tubing diameter and place the tubing with the end you have just prepared, extending above the top of the bar by a distance equal to the thickness of the shoulder of the adapter insert. 52  General 9-7 Double Flaring Instructions  Tighten clamping screws to hold tubing securely.  Insert pilot of correctly sized adapter into tubing.  Slip yoke over the flaring bars and center over adapter.  Advance the cone downward until the shoulder of the adapter rests on the flaring bar.  This bells out the end of the tubing.  Next, back off the cone just enough to remove the adapter.  After removing the adapter, advance the cone directly into the belled end of the tubing. 53  General 9-7 Double Flaring Instructions  This folds the tubing on itself and forms an accurate double flare without cracking or splitting the tubing.  To prevent thinning out of the flare wall, do not overtighten. [Figure 9-13].  How To Make a Double Flare 54  General 9-7 Double Flaring Instructions  Figure 9-13 55  General 9-7 Fittings  Rigid tubing may be joined to either an end item (such as a brake cylinder), another section of either rigid tubing, or to a flexible hose (such as a drain line).  In the case of connection to an end item or another tube, fittings are required, which may or may not necessitate flaring of the tube.  In the case of attachment to a hose, it may be necessary to bead the rigid tube so that a clamp can be used to hold the hose onto the tube. 56  General 9-7 Flareless Fittings  Although the use of flareless tube fittings eliminates all tube flaring, another operation referred to as presetting is necessary prior to installation of a new flareless tube assembly.  Flareless tube assemblies should be preset with the proper size presetting tool or operation.  The presetting operation is performed as follows: Cut the tube to the correct length, with the ends perfectly square.  Debur the inside and outside of the tube. 57  General 9-7 Flareless Fittings  Slip the nut, then the sleeve, over the tube, lubricate the threads of the fitting and nut with hydraulic fluid.  Place the fitting in a vise and hold the tubing firmly and squarely on the seat in the fitting. (The tube must bottom firmly in the fitting.)  Tighten the nut until the cutting edge of the sleeve grips the tube.  To determine this point, slowly turn the tube back and forth while tightening the nut.  When the tube no longer turns, the nut is ready for tightening. 58  General 9-7 Flareless Fittings  Final tightening depends upon the tubing.  For aluminum alloy tubing up to and including ½" outside diameter, tighten the nut from 1 to 1 1/6 turns.  For steel tubing and aluminum alloy tubing over ½ " outside diameter, tighten 1 1/6 to 1 ½ turns.  After presetting the sleeve, disconnect the tubing from the fitting and check the following points:  [Figure 9-14]The tube should extend 3/32" to 1/8" beyond the sleeve pilot; otherwise, blowoff may occur. 59  General 9-7 Flareless Fittings  The sleeve pilot should contact the tube or have a maximum clearance of.005" for aluminum alloy tubing or.015" for steel tubing.  A slight collapse of the tube at the sleeve cut is acceptable.  No movement of the sleeve pilot, except rotation, is permissible.  How to Assemble Tube Fittings Swagelok 60  General 9-8 Flareless Fittings Figure 9-14 61  General 9-7 Beading  Beading enlarges an area of a tube’s circumference to provide a section where pressure can be applied with a clamp.  Tubing may be beaded with a hand beading tool, machine beading rolls, or with grip dies.  The method used depends on the diameter and wall thickness of the tube and the material of which it was made.  The hand beading tool is used with tubing having 1⁄4" to 1" outside diameter. [Figure 9-15] 62  General 9-7 Beading  The bead is formed by using the beader frame with the proper rollers attached.  The inside and outside of the tube is lubricated with light oil to reduce the friction between the rollers during beading.  The sizes, marked in sixteenths of an inch on the rollers, are for the outside diameter of the tubing that can be beaded with the rollers.  Separate rollers are required for the inside of each tubing size, and care must be taken to use the correct parts when beading. 63  General 9-9 Beading.  Figure 9-15 64  General 9-8 Beading  The hand beading tool works somewhat like the tube cutter in that the roller is screwed down intermittently while rotating the beading tool around the tubing.  In addition, a small vise (tube holder) is furnished with the kit.  Other methods and types of beading tools and machines are available, but the hand beading tool is used most often. 65  General 9-8 Beading  As a rule, beading machines are limited to use with large diameter tubing, over 1 15⁄16", unless special rollers are supplied.  The grip-die method of beading is confined to small tubing.  Beading Aluminum Line 66  General 9-8 Fluid Line Identification  Fluid lines in aircraft are often identified by markers made up of color codes, words, and geometric symbols.  These markers identify each line’s function, content, and primary hazard.  Figure 9-16 illustrates the various color codes and symbols used to designate the type of system and its contents.  Fluid lines are marked, in most instances with 1" tape or decals. [Figure 9-17A] 67  General 9-8 Fluid Line Identification  On lines 4" in diameter (or larger), lines in oily environment, hot lines, and on some cold lines, steel tags may be used in place of tape or decals, as shown in Figure 9-17B.  Paint is used on lines in engine compartments, where there is the possibility of tapes, decals, or tags being drawn into the engine induction system.  In addition to the above-mentioned markings, certain lines may be further identified regarding specific function within a system; for example, drain, vent, pressure, or return. 68  General 9-10 Fluid Line Identification  Figure 9-16 69 Fluid Line Identification 70  General 9-10 Fluid Line Identification  Figure 9-17 Tube content Hazard 71  General 9-10 Fluid Line Identification  Figure 9-17 72  General 9-8 Fluid Line Identification  Lines conveying fuel may be marked FLAM. [Figure 9-17]  Lines containing toxic materials are marked TOXIC in place of FLAM.  Lines containing physically dangerous materials, such as oxygen, nitrogen, or Freon™, may be marked PHDAN. (physically dangerous)  Aircraft and engine manufacturers are responsible for the original installation of identification markers, but the aviation mechanic is responsible for their replacement when it becomes necessary. 73  General 9-8 Fluid Line Identification  Tapes and decals are generally placed on both ends of a line and at least once in each compartment through which the line runs.  In addition, identification markers are placed immediately adjacent to each valve, regulator, filter, or other accessory within a line.  Where paint or tags are used, location requirements are the same as for tapes and decals. 74