A400M Training Manual PDF - June 2020

Table of contents Chapter 1. Central Maintenance SubSystem - Description & Operations 1.1 Central Maintenance SubSystem - Description 1.1.1 General Description 1.1.2 Controls & Indications 1.1.3 Detailed Description 1.2 Central Maintenance SubSystem - Operation 1.2.1 General Operational Use 1.2.2 Post Flight Report 1.2.3 Previous Flight Reports 1.2.4 Ground Report 1.2.5 Avionics Status 1.2.6 System Report Test 1.2.7 Engineering Data Chapter 2. Data Loading & Configuration SubSystem - Description & Operations 2.1 Data Loading & Configuration SubSystem - Description 2.1.1 General Description 2.1.2 Controls & Indications 2.1.3 Detailed Description 2.2 Data Loading & Configuration SubSystem - Operation 2.2.1 General Operational Use 2.2.2 Uploading Operations 2.2.3 Downloading Operations 2.2.4 NSS Part Uninstallation 2.2.5 Equipment Identification 2.2.6 A/C Configuration 2.2.7 Software Pin Programming Released in June 15, 2020 TRAINING USE ONLY Training Use Only 1 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf Chapter 3. Aircraft Condition Monitoring SubSystem - Description & Operations 3.1 Aircraft Condition Monitoring SubSystem - Description 3.1.1 General Description 3.1.2 Controls & Indications 3.1.3 Detailed Description 3.2 Aircraft Condition Monitoring SubSystem - Operation 3.2.1 Condition Monitoring Reports 3.2.2 Real Time Monitoring 3.2.3 Data Recording Chapter 4. Structural Life Time Monitoring SubSystem - Description & Operations (Optional) 4.1 Structural Life Time Monitoring subSystem - Description 4.1.1 General Description - IM 4.1.2 General Description - IM+DM (Optional) 4.1.3 Controls & Indications 4.1.4 Component Location (Optional) 4.1.5 Detailed Description - IM 4.1.6 Detailed Description - DM (Optional) 4.2 Structural Life Time Monitoring subSystem - Operation 4.2.1 Data Display and Downloading Chapter 5. Aircraft Integrated Monitoring and Diagnostic System - Maintenance 5.1 On Board maintenance System 5.1.1 OMS Pages 5.2 Maintenance Tasks 5.2.1 Maintenance Procedures Released in June 15, 2020 TRAINING USE ONLY Training Use Only 2 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual ATA 45 Aircraft Integrated Monitoring and Diagnostic System Released in June 15, 2020 TRAINING USE ONLY Training Use Only 3 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations General Description Chapter 1. Central Maintenance SubSystem - Description & Operations 1.1 Central Maintenance SubSystem - Description 1.1.1 General Description General Description CMS Architecture The Central Maintenance System (CMS) main component is a software application called CMS Application. The CMS Application is redundant, and resides in both Integrated Network Server Units (INSUs), which are part of the Network Server System (NSS). The CMS applications use the basic shared services offered by the NSS: - Shared Database, which is used by the CMS to store maintenance information - NSS Human Machine Interface (HMI), which are the Printer and the Aircraft Multipurpose Access Terminal (AMAT) - INSUs connections to Portable Multipurpose Access Terminal (PMAT) - Secure communications with the aircraft systems. The information coming from the avionics are BITE messages sent by the Line Replaceable Units (LRUs) and Line Replaceable Modules (LRMs). The CMS transmits BITE requests to the aircraft LRUs and LRMs in order to initiate interactive tests when required by the operator. In addition, the CMS acquires operational data: - Failure messages and Flight Deck Effects from the Flight Warning System (FWS), Control Display System (CDS) and Head Up Display System (HUDS) - Aircraft parameters from other systems When the aircraft is on ground, the CMS application can be accessed and controlled from the Maintenance Access Terminals (AMAT and PMAT). Aircraft system failure reports can be generated by various CMS pages, the operator has the option to view the report on the MAT screen or print the applicable report. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 4 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations General Description 5 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 1.1.2 Central Maintenance SubSystem - Description & Operations Controls & Indications Controls & Indications Controls and Indications General The Multipurpose Access Terminals (MATs) provide the operator with the CMS human-machine interface. The MATs allow the operator to access various CMS functions: - Post flight report - Previous flight reports - Ground report - Avionics status - System report test - Engineering data It is possible for the operator to print the reports. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 6 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Controls & Indications 7 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Controls & Indications CMS Menu The "CMS Menu" is the initial page of the CMS. From this page, the operator can select the desired function. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 8 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Controls & Indications 9 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 1.1.3 Central Maintenance SubSystem - Description & Operations Detailed Description Detailed Description BITE Interface BITE Definition The BITE is a software function implemented in A/C systems, to analyze all parameters associated with any detected failure. The CMS acquires fault symptoms from the aircraft systems and in particular from BITEs of the Line Replaceable Units (LRUs) and the Line Replaceable Modules (LRMs) or aircraft wiring being the cause of the failure. There are two modes of communications between BITEs and CMS: - The Normal Mode (on ground and in flight) is a one way reporting transmission from BITE to CMS. In normal mode, the CMS: - Does system continuous monitoring. - Detects and identifies failures. - Centralizes failure events and parameters sent by the BITEs. - The Interactive mode (only on ground) is a duplex communication between BITE and CMS for testing and specific BITE data access. The interactive mode gives access to: - Interactive system tests. - Systems monitoring. - Maintenance history. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 10 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Detailed Description 11 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Detailed Description BITE, Operational Effects and Post Flight Report Correlation (I) A/C systems fault detection is achieved by an internal monitoring and test function which resides in all systems. The monitoring function of A/C equipment sends the fault information to the Flight Warning System (FWS) and also to other A/C Systems as CDS, HUD or IPCS if the fault causes a Flight Deck Effect (FDE). These systems (FWS, CDS, HUD, ICPS...) use the fault information to determine and generate the related alerts to be displayed as Operational Effects on the Cockpit and LMWS systems. Also, all faults detected by the A/C system internal monitoring and test functions are acquired by its internal BITE. The system BITE processes the fault information to elaborate and transmit BITE Failure messages or Maintenance Fault messages to the CMS. The Operational Effects information (FDE information, Fault Message, Time remaining...) is also sent continuously from the FWS, CDS, and HUD to the CMS at regular intervals. The CMS makes a link and a correlation with the Operational Effects and the BITE Fault Messages or Maintenance Fault Messages in order to determine a related fault case. This link is provided by the Post Flight Report generated by the CMS. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 12 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Detailed Description 13 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Detailed Description BITE, Operational Effects and Post Flight Report Correlation (II) An Operational Effect provides information about operational faults dedicated to the flight crew and necessary for operational purposes. The BITE is a fault isolation and reporting function only for On-Board maintenance purposes, not for fault detection. Fault detection is done by system monitoring within each system and test functions. It means that BITE function failure messages do not provide info to the flight crew and are not necessary for operational purpose. The BITE function failure messages are dedicated to maintenance technicians or engineers to support the diagnostic trouble shooting actions. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 14 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Detailed Description 15 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Detailed Description Fault Case Definition During the flight, the CMS receives all symptoms related to systems failures. A failure may lead to secondary malfunctions on other systems. The CMS correlates all those symptoms caused by the same original failure and gathers them in a structured common item called “Fault Case”. Fault cases mainly contain FMs and FDEs but also contextual data such as flight phase. Each Fault case is characterized by a main Failure Message (fault origin) and a main Flight Deck Effect associated to the primary failure. Then “Post Flight Report items”, which contains one fault case, are created. Besides, as much as possible, a unique fault origin associated to this PFR Item will be determined. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 16 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Detailed Description 17 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Detailed Description PFR Item Example The following picture shows an example of a Post Flight Report item where a correlation of Operational Effects with a Maintenance Fault Message has been provided by the CMS. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 18 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Detailed Description 19 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Detailed Description Fault Code Description Each Fault Message and FDE is identified by a unique identifier for a failure event. This identifier is the Fault Code which is composed as follows: - The four first digits agree with the ATA chapter/sub-chapter related to the event. - One letter related to the fault type. - W: an ECAM warning - N: an ECAM Inoperative Status - F: a fault message - G: a flag on Display Unit (DU) - A: an advisory on DU - D: other flight deck or cabin effect on CDS - X: a local effect monitored - L: a local effect plus a CDS effect non monitored - C: an observation non monitored and not localized - B: an observation out of TSM scope for E-logbook - E: a cabin malfunction - Three last characters are dedicated to the event number for memorization in CMS database. The Fault Codes are used as entries in the Air-vehicle Fault Isolation (AFI) manual to provide technicians with the appropriate troubleshooting procedure. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 20 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Detailed Description 21 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Detailed Description PFR Data Recording During a Flight A leg is the period of time that contains a Maintenance Phase and a Flight. The Flight condition is determined between start-up of the third engine plus 3 minutes, with flight plan available in the Flight Management System (FMS), and 50 knots and 150 seconds after touch down. During the flight, the Post Flight Report records maintenance and operational data received by the CMS. The Post Flight Report correlation is launched at the end of the last leg. Thus, the Post Flight Report treats Failure Messages and Flight Deck Effects that have been present during at least a part of this leg. The failure messages generated during the Maintenance Phase are managed by a different function, the Ground Report. It starts after the Post Flight Report closure. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 22 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Detailed Description 23 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations General Operational Use 1.2 Central Maintenance SubSystem - Operation 1.2.1 General Operational Use General Operational Use CMS Starting Provided that the aircraft is on ground and the access to the Air Framer Shell (AFRS) is granted by the IA4CS, the CMS is available from the AFRS main page by clicking on its corresponding button. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 24 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations General Operational Use 25 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations General Operational Use CMS Menu Once the CMS is started and the CMS Main Menu is displayed, the user can access to three types of functions: - Maintenance functions, which provide failures reports: - Post Flight Report - Previous Flight Reports - Ground Report - Avionics Status. - BITE functions, which allows performing interactive tests through the System Report Test - Engineering functions, which allows retrieving some specific data through the Engineering Data Released in June 15, 2020 TRAINING USE ONLY Training Use Only 26 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations General Operational Use 27 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 1.2.2 Central Maintenance SubSystem - Description & Operations Post Flight Report Post Flight Report Post Flight Report Operation Displays Access to Post Flight Report From the main menu of the CMS the operator can select the “Post Flight Report” shortcut and thus get access to the Post Flight Report screens. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 28 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Post Flight Report 29 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Post Flight Report Post Flight Report The Post Flight Report gathers maintenance information on failures, which occurred during the last flight (from "take-off" to "taxi-in”). By default, it is automatically printed at the end of the flight. The automatic print trigger can be inhibited if necessary. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 30 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Post Flight Report 31 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Post Flight Report Post Flight Report Display (I) The PFR display is structured as follows: - A general information field containing the mission number, the flight number, and the departure and arrival dates. - A field with four tabs. Each tab shows a sub-report that contains a defined class of Fault Cases. - A list of Fault Cases. The PFR tabs sort out the Fault Cases in different classes that are defined in consequence with their operational effect. The “Cockpit effect” tab contains Fault Cases that cause a Flight Deck Effect. The “Maintenance status” tab contains Fault Cases that generate a maintenance status and for which a corrective action is necessary. The “Potential cockpit effect” tab contains Fault Cases that have not an immediate Flight Deck Effect but will cause a Flight Deck Effect when combined with other faults. It also contains Fault Cases that have an unknown effect on system operation. The “Maintenance fault” tab contains Fault Cases that do not cause a Flight Deck Effect and without safety involvement. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 32 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Post Flight Report 33 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Post Flight Report Post Flight Report Display (II) If the operator selects "Cockpit Effect" tab or "Maintenance Status" tab, the following information is summarized in the fault cases layout of Post Flight Report: - No: Number of the item in the list and total number of items in this tab. - Operational Effects: Description of the FDE message (fault code, label, title). - Date-UTC / Flight of Phase: Date of reception and Flight Phase or “Before flight” if failure appeared before flight beginning. - Maintenance Messages: Fault case description: Fault Message origin of each Fault Case, Fault Code of the Failure Message origin, status, source and other Failure Messages or Flight Deck Effects associated. If there is other breakdown message associated with a displayed one, the symbol “>>” will be displayed on the extreme right of the first line. This symbol means that in page Items details, more FDEs and FMs will be displayed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 34 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Post Flight Report 35 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Post Flight Report Post Flight Report Display (III) If the operator selects "Potential Cockpit Effect" tab or "Maintenance Fault" tab, the following information is summarized in the fault cases layout of the Post Flight Report: - No: Number of the item in the list and total number of items in this tab. - Date-UTC / Flight of Phase: Date of reception and Flight Phase or “Before flight” if failure appeared before flight beginning. - Fault case description: Failure Message class, Fault Code of the Failure Message origin, message display, status, source and other Failure Messages or Flight Deck Effects associated. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 36 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Post Flight Report 37 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Post Flight Report Post Flight Report Fault Details When the operator selects a fault case in the PFR by clicking on a line of the report, he/she gets access to the Fault Detail page. This page gives more detailed information of the fault case and shows the following data: - Correlated Flight Deck Effects: It is the list of warnings sent by the FWS and the flags/advisories sent by the CDS and the HUD. For each effect, these parameters are shown: - Date-UTC / Flight of Phase. - Operational Effects. Description of the FDE message, Fault Code, FDE type and title. - Correlated Failure Messages: It is the list of FMs sent by the system BITE. For each FM, these parameters are shown: - Date-UTC / Flight of Phase. - Maintenance Messages. Description of the message, Class of the Failure Message and Fault Code. The root cause failure is displayed in bold. - Fault Message Status: "Status" label shows the state of the failure at the end of the flight. It can take different values: - Latched: Faults that have an occurrence open when PFR is generated. - Intermittent: Faults that have disappear at least one time in flight. - Present: Status is not latched or intermittent. - Source: source side and source ATA. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 38 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Post Flight Report 39 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 1.2.3 Central Maintenance SubSystem - Description & Operations Previous Flight Reports Previous Flight Reports Previous Flight Report Operation Displays Access to Previous Flight Reports From the main menu of the CMS, the operator can select “Previous flight reports”. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 40 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Previous Flight Reports 41 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Previous Flight Reports Previous Flight Reports The operator has the possibility to access CMS historical data through the previous flight reports feature. The CMS database is designed to record up to 64 PFRs. All PFRs recorded except the last one are listed in the Previous Flight Report menu page. Hence, the operator can get access to 63 previous PFRs. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 42 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Previous Flight Reports 43 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Previous Flight Reports Previous Flight Report Display For each Previous Flight Report in this list the next parameters will be displayed: - Mission number related to the leg. - Flight number related to the leg. - Leg number. - Departure time and date. - Arrival time and date. By default, this list is sorted by the leg number. But all the parameters can be used to sort it. The Previous Flight Reports are presented the same way as the Post Flight Report, and they provide similar functionalities as the Post Flight Report. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 44 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Previous Flight Reports 45 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Previous Flight Reports Previous Flight Report History Page A click on the line with the correct leg of the Previous Flight Report menu page displays one previous PFR called "Previous Flight Report History". The data displayed in the page “Previous Flight Report History” page is mainly the same as the data displayed in the page “Post Flight Report”, excepting following points: - The page title displayed is extended with the leg number (4 digits) of the considered leg. - The data displayed is the one related to the considered leg (for instance, the one selected in the “Previous Flight Report menu” page), and not the one related to the last leg. - The selection of a line in the list leads to the page “Item detail history” related to the selected item in the same instance, instead of the page "Item detail" - The button back leads to the page "Previous Flight Reports Menu". Released in June 15, 2020 TRAINING USE ONLY Training Use Only 46 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Previous Flight Reports 47 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Previous Flight Reports Item Detail History Page By clicking on a line of the Previous Flight Report History page the page “Item detail history” related to the selected item is displayed. The data displayed in the page “Item detail history” page is mainly the same as the data displayed in the page “Fault Detail” of the Post Flight Report, excepting the following points: - The page title displayed is extended with the leg number (4 digits) of the considered leg. - The button back leads to the last page from which the “Item detail history” page was accessed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 48 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Previous Flight Reports 49 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 1.2.4 Central Maintenance SubSystem - Description & Operations Ground Report Ground Report Ground Report Operation Displays Access to Ground Report From the main menu of the CMS, the operator selects “Ground Report”. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 50 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Ground Report 51 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Ground Report Ground Report The ground report allows the operator to monitor systems and generate failure reports while the aircraft is on ground. The Ground Report contains only maintenance faults that appeared on ground after the last flight but it does not report any operational effects nor correlated failure messages. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 52 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Ground Report 53 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Ground Report Ground Report Selection Page Through the Ground Report selection page, the CMS is able to display a list of all systems from which the operator can choose several systems to be included in the ground report. - First, the operator has to select a function title (ATA chapter) in the scrolling menu “Function”. - Then the operator selects the systems on which he/she wants the BITE from the list of available BITEs to the list of the selected BITEs. The operator can proceed simultaneously to several BITEs but from the same system. - Finally the operator clicks on the button “Generate the report” to launch the request. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 54 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Ground Report 55 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Ground Report Ground Report Results Page (I) When the report is generated, the result is presented in a table format. Each line corresponds to one failure. The information that can be found is: - List of selected systems. - Date and UTC of failure reception and Flight Phase: the breakdown context with the date and the hour of the detection and the Flight Phase associated. - Fault case description: Description of the Failure Message class, fault code of the Failure Message, Failure Message display and source. The ground report will contain none correlated failure messages that appeared on ground after the last flight. The ground report is not updated in real time. It reflects the systems state at the opening of the report. Standard B and standard A failures from the selected A/C electronic systems will be reported in the ground report. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 56 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Ground Report 57 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Ground Report Ground Report Results Page (II) If there is no fault message for this system, the message "No failure detected" is displayed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 58 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Ground Report 59 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 1.2.5 Central Maintenance SubSystem - Description & Operations Avionics Status Avionics Status Avionics Status Operation Displays Access to Avionics Status From the main menu of the CMS, the operator selects “Avionics Status". Released in June 15, 2020 TRAINING USE ONLY Training Use Only 60 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Avionics Status 61 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Avionics Status Avionics Status The avionics status allows the operator to display in real time the list of failure messages of a system or a group of systems. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 62 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Avionics Status 63 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Avionics Status Avionics Status Selection Page The operator first selects a function title (ATA chapter) of the systems he/she wants to monitor in the scrolling menu “Function”. Then the operator selects the system/systems of which he/she wants to perform a system BITE. Only systems with failures or silent are displayed. Finally, the operator clicks on the button “Start the scan” to launch the request. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 64 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Avionics Status 65 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Avionics Status Avionics Status Results Page When the report is generated, the system monitoring result page is shown to the operator. It contains the BITE messages sent to the CMS by the selected systems. Each item related to a received Failure Message contains: - Date-UTC: Its apparition time. - Fault code. - Failure Message display. - Class of the Failure Message. At the top of the display the status of the monitoring is indicated. From the avionics status page, there is a direct access to the system report test function. The "Avionic status" function is able to monitor all installed systems, except the ones already in interactive mode. If the system is silent, the message "No Response from BITE" will be displayed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 66 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Avionics Status 67 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 1.2.6 Central Maintenance SubSystem - Description & Operations System Report Test System Report Test System Report Test Operation Displays Access to System Report Test Two ways are possible to get access to the system report test pages: - From the CMS main menu: The operator selects first the System Report Test function (ATA chapter) and then he/she selects the system to be tested. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 68 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 69 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test Access to System Report Test (continued) - From the Avionics Status pages, through a hyperlink: The parameters are already selected and the test is automatically launched. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 70 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 71 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test System Report Test The System report/test function allows the operator to get access to interactive mode. It allows the operator to execute interactive tests on BITE and specific maintenance functions. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 72 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 73 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test System Report Test Selection The operator has to select first a function title (ATA chapter) "ATA System" scrolling list. A list of subsystems with BITE available of the selected ATA chapter will appear on the “BITE System” scrolling list. By double clicking on the selected subsystem, the corresponding System Report Test page will appear. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 74 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 75 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test System Report Test Side Selection The standard System Report Test Side selection page contains the following information: - ATA BITE and ATA title. - BITE name. - List of the system element name of the selected BITE. - Return to the function selection page button. The operator selects the system element name side and the monitoring starts. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 76 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 77 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test System Report Test Sequence Once the subsystem has been selected, the test can be launched pressing the dedicated test pushbuttons. After that, a series of customized screens appears related to each system BITE and on the last page, named the “Result page”, a table is displayed containing the failure messages with related fault code and class if any. No more screenshot are detailed in this topic because the displays layout depends on the system to be tested and the dedicated CMS pages will be explained in every ATA chapter. Note that in the selection page of an interactive operation, some buttons may not correspond neither to a test, nor to a specific function. They can be differentiated from the other buttons by a relief effect and ellipsis at the end of the heading. These buttons represent a menu and give access to new sub-lists of tests, specific functions or menus. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 78 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 79 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test Interruption of an Interactive Session If the operator wants to close the interactive session, he can: - Click on the "Close" button of the AFRS menu, whenever he wants. - Click on the icon Close of the CMS, whenever he wants. - Click on the « ABORT » button when it is present and enabled on the interactive page. Then three situations can happen: - If the session is not interruptible, the closing procedure is stopped. - If conditions must be checked at the end of the test, consequently they are displayed in a page of type “Close-up conditions”. When the conditions are checked, the operator will have to click on the page button of the interactive zone to close definitively the interactive session and hence, the associated tab will disappear. - If no conditions must be checked at the end of the test then the tab of the interactive sessions is closed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 80 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 81 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test Result of a Test or Specific Function (I) The interactive page “Result” contains information about possible causes to system faults. When there are no problems during the test or the specific function course, the message « TEST OK » is displayed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 82 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 83 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test Result of a Test or Specific Function (II) Otherwise, it will show “SYSTEM FAULT” and the breakdown messages will be positioned in a table. The available information is the message, the fault code and the breakdown class. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 84 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 85 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test Tests with Caution (I) The hazardous tests are only available for standard B type 1 BITEs. The interactive page "Dangerous step: confirmation procedure" is composed of two screens. The first screen is an information page about the confirmation procedure. The "Start confirmation" button opens the second screen, where the confirmation code is entered. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 86 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 87 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test Test with Caution (II) The user has three attempts of 40 seconds each to enter the code displayed on the screen, the timer starts with the activation of the "Start Confirmation" button. After three failed attempts, the abort procedure of the test is launched. After having composed a 4 alphanumeric character code, the user can confirm with the "Validate" button. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 88 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 89 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations System Report Test Error Pages During the test procedures, different types of error´s can happen. Here are a few explanations on the error pages. - The protocol error occurs when there is a problem or an interruption of the communication between a system and the CMS. A fault code is associated on the upper right corner. - The “Error launching the test” will appear when the passage in the interactive mode has failed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 90 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations System Report Test 91 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 1.2.7 Central Maintenance SubSystem - Description & Operations Engineering Data Engineering Data Engineering Data Operation Displays Access to Engineering Data From the main menu of the CMS the operator can select “Engineering Data”, to access to the "Engineering Data" menu. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 92 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 93 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Engineering Data The engineering data function allows the operator to: - Proceed to a maintenance data extended search - Program the automatic printing of the PFR - Manage the database. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 94 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 95 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Report Programing Displays From the “Engineering Data Menu” page, the operator clicks on the “Report Programming”. The following page is used to enable or disable the automatic printing of the Post Flight Report at the end of each flight. By default, this function is disabled. Once the choice is made, the operator can return to sub-menu Engineering data by clicking on the Engineering data menu. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 96 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 97 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Database Dump Displays (I) From the “Engineering Data Menu” page, the operator clicks on the “Database Dump” button. This function generates an archive containing all the data from the CMS database. The database dump function may take several minutes due to the size of the file, the operator has to confirm the dump of the database before it is launched. He clicks on the “Start database dump” button to launch the dump process. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 98 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 99 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Database Dump Displays (II) A new page shows the progress status, it contains a time counter and a progress bar. The text “Dump finished” appears at the end of the dump. During this operation, the CMS is operational. The "Engineering Data Menu" button allows the operator to return to the previous menu to perform other actions (during the dump or when the dump is finished). Released in June 15, 2020 TRAINING USE ONLY Training Use Only 100 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 101 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data CMS History Clear Displays (I) From the “Engineering Data Menu” page, the operator clicks on the “CMS history clear” button. The CMS History Clear pages allow the operator to completely erase the information contained in the CMS database. Due to it is a critical action; the database clear is protected by a password. The operator has to enter the password. Then he clicks on the “OK” button. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 102 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 103 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data CMS History Clear Displays (II) A confirmation page appears to inform the operator about the pending data erasure and allows the cancellation or confirmation of the operation. The "Confirmation page" stays displayed during 2 minutes, if the clear has not been confirmed during this time period, the application goes back to "Password entry" page. The operator must confirm the database clear. The CMS is not operational during this operation. The clear will be launched if no CMS sub-application is opened. Or else a popup Note will be displayed. There are another few conditions to initiate the clear: - If a non - interruptible interactive session is active, all the dialogs will have to be stopped manually. - Only one MAT can be connected to the CMS server. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 104 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 105 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data CMS History Clear Displays (III) Once the conditions are fulfilled and the clear is confirmed, a bar is displayed showing the clear progression. The sub-applications are not accessible during this time. Once the process is finished, a pop-up window appears with the clear result: success or fault. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 106 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 107 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Maintenance Data Extended Search Displays From the “Engineering Data Menu” page, the operator clicks on the “Search” button. The displayed menu allows the operator to do a specific data search using either maintenance message or operational effect according to determined criteria. This menu is different depending on data type requested. The operator selects a data type in the scroll-down menu “Select a data type”. This type can be maintenance messages or operational effect. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 108 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 109 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Maintenance Messages Search Pages (I) In the Maintenance Messages Search Pages, the operator can filter the search according to: - Interval time of the occurrence. - Mission number and flight number. One Mission number can be associated to many flight numbers. And each flight number mission can be associated to many leg numbers. - Source ATA, system and side. - Name of LRU. - Fault code. - Class. - Failure Message content. The operator clicks then on “Search” button to launch the search. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 110 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 111 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Maintenance Messages Search Pages (II) Once the search is performed, the following data is displayed on the “Maintenance messages search results” page: - The date and time of the considered maintenance message and the flight phase related. - The associated mission number. - The associated flight number. - The fault class of the fault occurrence. - The fault code of the fault occurrence. - The maintenance message display. - The maintenance message source name. - The maintenance message detection Mode: “Interactive test” if the fault has been reported in interactive mode (as result of an interactive test). “Continuous monitoring” if the fault has been reported in normal mode. If the operator clicks on an item on the “Maintenance messages search result” page, he gets access to the fault detail page. If the operator clicks on the “new search” button, he can launch a new search. This button is disabled until the user enters a new search criterion. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 112 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 113 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Operational Effects Search Pages (I) In the Operational Effects Search Pages, the operator can filter the search according to: - Interval time of the occurrence. - Mission number and flight number. One Mission number can be associated to many flight numbers. And each flight number mission can be associated to many leg numbers. - Source: All, FWS, CDS, HUD, Local or Other. - Level: All, Warning, Caution, Awareness or Other. - Fault Code. - Title. The Flight Deck and Cockpit Effect title or a part of it. When the operator clicks then on “Search” button, a new search will be launched. This button is disabled until the user enters a criterion. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 114 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 115 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Operational Effects Search Page (II) The data displayed on the “Operational Effects search results” page are the following: - The chronological date and time of the considered maintenance message and the related flight phase. - Mission number of the fault occurrence. - Flight number of the fault occurrence. - Fault Code. - Type of the fault occurrence. - Flight Deck Effect of the fault occurrence. - Source of the fault occurrence. - Display block: Will indicate either “Displayed or Not Displayed” if any operational effect has been displayed in the cockpit or not. When the operator clicks on an item on the “Maintenance messages search result” page, this will open another more detailed page. If the operator clicks on the “new search” button, this will launch a new search. This button is disabled until the user enters a criterion. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 116 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 117 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Engineering Data Fault Detail Page (I) The fault detail page shows a more in-depth detailed description of the fault from engineering data search result. It is divided in 3 parts: - Fault display. A brief summary of the fault code and the fault message. - Fault data. Detailed information for engineering purpose. - Failed / healthy LRU - Wiring. In this part, the table contains the information based on the message origin. The three first lines show the possible components causing the failure and the logical connection between them are contained in the small boxes on the left of the table. The "Details fault data" button opens a new page containing the failure data of the maintenance message. The "New Search" button closes this page and re-opens the database search page with the default search parameters Released in June 15, 2020 TRAINING USE ONLY Training Use Only 118 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 119 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Central Maintenance SubSystem - Description & Operations Engineering Data Engineering Data fault Data Page (II) The “Details fault data” page contains engineering and complementary data related to the component causing the failure. This information can be exported or printed in order to be sent to system designers. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 120 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Central Maintenance SubSystem - Description & Operations Engineering Data 121 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations General Description Chapter 2. Data Loading & Configuration SubSystem - Description & Operations 2.1 Data Loading & Configuration SubSystem - Description 2.1.1 General Description General Description DLCS Architecture The Data Loading and Configuration System (DLCS) main component is a software application called DLCS Application. The DLCS Application is redundant, and resides in both INSUs. The DLCS applications use the basic shared services offered by the NSS: - The Printer and AMAT - INSUs connections to PMAT - Secure communications with the aircraft systems. The AMAT and PMAT are used as media readers and writers. Also, the PMAT Hard Discs can be used for storing downloaded data. The DLCS allows software and data base loading from various media sources to aircraft computers and vice versa. There are two types of targets: - Line Replaceable Units (LRUs) - Line Replaceable Modules (LRMs) The DLCS receives configuration data to allow the generation of aircraft and equipment configuration reports. The Software Pin Programming (SPP) Function is used for the storage and the distribution of SPP loads, which determine the configuration of many aircraft systems. The SPP loads are broadcasted cyclically to the aircraft LRUs and LRMs. The SPP loads are uploaded using the DLCS. At operator request, the DLCS can read the broadcasted SPP, and display this information on any Maintenance Access Terminal. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 122 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations General Description Provided the aircraft is on ground, the DLCS can be accessed and controlled from the terminals (AMAT and PMAT). The systems data downloaded by the DLCS and the configuration reports can be displayed on the terminals or sent to the printer. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 123 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations General Description 124 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 2.1.2 Data Loading & Configuration SubSystem Description & Operations Controls & Indications Controls & Indications DLCS HMI General The MATs provide the DLCS with the human-machine interface There are two access types: - Mission Data Operations, for flight crew. - Maintenance Data Operations, for maintainers. The Maintenance Data Operations allow: - Maintenance Uploading - Maintenance Downloading - Equipment Identification - A/C Configuration - Software Pin Programming - NSS Part Uninstallation It is possible for the operator to print the downloaded reports. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 125 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Controls & Indications 126 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Controls & Indications DLCS Menu From the AFRS Main Menu, depending on IA4CS credentials, the operator can start either the DLCS (for maintenance) or the Mission DLCS (for pilots). Both pages have a panel where the operator can select the desired function. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 127 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Controls & Indications 128 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 2.1.3 Data Loading & Configuration SubSystem Description & Operations Detailed Description Detailed Description Maintenance Data Loading and Uninstallation Functions Data Uploading The uploading operation is a data transfer from a portable media (CD/DVD-ROM, PCMCIA card) or from PMAT hard drive to an avionics target. A target is any loadable LRU or LRM of the aircraft systems or the INSU. A load is a software, data or SPP file to be uploaded to its target. The uploading process is achieved in several steps: 1. When the operator logs on a MAT, access is granted by the IA4CS according to his credentials. The operator can launch the “Maintenance Upload” function from the MAT. 2. After the target, media and load have been selected, upload can be launched. Data transferring from the media is initiated. 3. The DLCS receives and authenticates the load. 4. The DLCS sends the load to the selected targets. 5. The targets send to the DLCS information about progress and status. 6. As feedback, the DLCS sends progress and status information to MAT in order to be displayed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 129 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Detailed Description 130 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Detailed Description Data Downloading The downloading process is achieved in several steps: 1. When the operator logs on a MAT, access is granted by the IA4CS according to his credentials. The operator can launch the “Maintenance Download” function from the MAT. 2. The operator selects a target (LRU, LRM or INSU), which sends the downloadable files list to the Data Loading and Configuration System. 3. The DLCS provides the MAT with the list of files, which is displayed for the operator. 4. After file and media selection by the operator, downloading can be launched. The DLCS gets the files from the selected target. 5. The DLCS download the files to the MAT. 6. The MAT writes data on the selected media (PCMCIA card or PMAT hard drive). 7. The targets send progress and status to the DLCS. 8. As feedback, the DLCS sends progress and status information to MAT in order to be displayed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 131 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Detailed Description 132 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Detailed Description NSS Part Uninstallation The NSS Part Uninstallation is used to uninstall NSS software hosted in the INSU. It is achieved as follows: 1. When the operator logs on a MAT, access is granted by the IA4CS according his credentials. The operator can launch the “NSS Part Uninstallation” function from the MAT. 2. The DLCS provides the MAT with the list of NSS un-installable software, which is displayed to the operator for selection. 3. After software selection by the operator, the DLCS requests the INSU Installation Service to uninstall the software. 4. The Installation Service actually performs the uninstallation of the selected NSS software. 5. The Installation Service communicates the progress and status information. 6. As feedback, the DLCS sends progress and status information to MAT in order to be displayed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 133 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Detailed Description 134 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Detailed Description Reporting Functions Configuration Reporting The Configuration Reporting function provides the operator with the hardware and software configurations of the LRUs and LRMs installed in the aircraft. There are two reporting functions, Equipment Identification and Aircraft Configuration. The Equipment Identification report is achieved as follows: 1. When the operator logs on a MAT, access is granted by the IA4CS according to his credentials. The operator can launch the “Equipment Identification” function from the MAT. 2. The DLCS provides the MAT with the list of targets, which is displayed to the operator for selection. 3. After target selection by the operator, the target sends its configuration to the DLCS. 4. The DLCS communicates the received configuration report to the MAT for display. The Aircraft Configuration report is achieved as follows: A. All LRUs and LRMs send periodically configuration data to the DLCS. The DLCS build´s the A/C Configuration report, which is updated every 140 seconds. B. One A/C Configuration report is automatically stored per flight at landing. The stored reports can be downloaded from INSU database for ground use. C. When an operator log´s onto a Maintenance Access Terminal and access is granted by the IA4CS. D. The operator launches the “A/C Configuration” function and the DLCS provides the MAT with the list of all LRUs and LRMs in the aircraft. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 135 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Detailed Description 136 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Detailed Description SPP Display The Software Pin Programming function allows the operator to display the installed and broadcasted SPP of the aircraft: 1. When an operator logs onto the MAT, and access is granted by the IA4CS according to his credentials. The operation can launch the “Software Pin Programming” function from the MAT. 2. The DLCS acquires the list of SPP values according the broadcasted SPPs. 3. The DLCS acquires the SPP meanings provided by the INSU Installation Service. 4. The DLCS provides the MAT with the SPP report to be displayed. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 137 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Detailed Description 138 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations General Operational Use 2.2 Data Loading & Configuration SubSystem - Operation 2.2.1 General Operational Use General Operational Use DLCS Starting for Maintenance Operators Provided that the aircraft is on ground and the access is granted by the IA4CS, the maintenance DLCS is available from the MAINTAINER area on the AFRS main page. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 139 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations General Operational Use 140 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations General Operational Use Maintenance DLCS Menu The maintainer can access to two types of DLCS functions: - Data loading, which allows: - Maintenance Upload - Maintenance Download - NSS Part Uninstallation - Reporting, which provides information about: - Equipment Identification - Aircraft Configuration - Software Pin Programming. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 141 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations General Operational Use 142 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations General Operational Use DLCS Starting for Pilots The DLCS start page for flight crew is the MISSION DATA OPERATIONS page. The flight crew can access this page by clicking “Mission DLCS” on the Air Framer Shell main page. Then the pilot can select the desired function. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 143 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations General Operational Use 144 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 2.2.2 Data Loading & Configuration SubSystem Description & Operations Uploading Operations Uploading Operations Maintenance Uploading Maintenance Uploading Selection From the main menu of the DLCS, the operator selects “Maintenance Uploading”. Then the maintenance uploading target selection screen appears. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 145 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Uploading Operations 146 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Uploading Operations Maintenance Uploading Page The Maintenance Uploading page allows the software update or the new software installation in a computer (target). Released in June 15, 2020 TRAINING USE ONLY Training Use Only 147 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Uploading Operations 148 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Uploading Operations Maintenance Uploading - Target Selection Screen (I) The operator can search for the target by entering the appropriate data in the filtering fields: - Hardware FIN. - Hardware Designation. - ATA Chapter (or Sub-ATA): - System. Once the operator has introduced the desired filtering criteria, the Search button will be enabled. By pressing this button the operator executes the search according to the filtering criteria. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 149 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Uploading Operations 150 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Uploading Operations Maintenance Uploading - Target Selection Screen (II) Then, the operator double-clicks on the target and the Maintenance Uploading - Software Selection screen appears. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 151 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Uploading Operations 152 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Uploading Operations Maintenance Uploading - Software Selection Screen In the Maintenance Uploading-Software Selection screen the operator has to select the applicable data source: CD, DVD ROM, PCMCIA card or MDS. Once the data source has been selected a list of available Software appears in the data source. The operator selects the Software in the list and he/she can click on ”Upload Software” button. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 153 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Uploading Operations 154 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Uploading Operations Maintenance Uploading - Progress Screen (I) The uploading will start and the system will show the progress status of the process. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 155 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Uploading Operations 156 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Uploading Operations Maintenance Uploading - Progress Screen (II) Once the progress is completed (100%) a green “Complete” label will appear in the Status field. The operator then can check the configuration of the uploaded target. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 157 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Uploading Operations 158 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 2.2.3 Data Loading & Configuration SubSystem Description & Operations Downloading Operations Downloading Operations Maintenance Downloading Maintenance Downloading - Selection From the main menu of the DLCS, the operator selects “Maintenance Downloading”. Then the Maintenance Downloading - Target Selection screen appears. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 159 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Downloading Operations 160 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Downloading Operations Maintenance Downloading Page The Maintenance Downloading page allows the operator to select the target and the destination of the downloaded file. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 161 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Downloading Operations 162 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Downloading Operations Maintenance Downloading - Target Selection Screen (I) The operator can search the target to download (avionics target or INSU for NSS download) by using filtering criteria: - Hardware FIN. - Hardware Designation. - ATA Chapter (or Sub-ATA): - System. The operator also can select the destination of the downloaded files (PCMCIA card or PMAT Hard drive). Once the operator has introduced the desired filtering criteria, the Search button will be available. By pressing this button the list of downloadable files from the filtered target will appear. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 163 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Downloading Operations 164 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Downloading Operations Maintenance Downloading - Target Selection Screen (II) Finally the operator selects the target. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 165 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Downloading Operations 166 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Downloading Operations Maintenance Downloading - Avionics File Selection Two screens are then possible according to the target. If the target is an Avionics equipment, the following screen appears. The operator selects the targets and clicks on “Start Download File". Released in June 15, 2020 TRAINING USE ONLY Training Use Only 167 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Downloading Operations 168 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Downloading Operations Maintenance Downloading - NSS File Selection (I) If the target is an NSS part (i.e. an INSU), the screen named NSS File Selection appears. This screen consists of the following filtering areas to filter the downloadable files: - "Data" allows to filter the files regarding their type. - "From System" area allows to filter the files regarding the system they belong to. - "From/To" area allows to filter the files regarding their date, flight number and/or mission number. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 169 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Downloading Operations 170 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Downloading Operations Maintenance Downloading - NSS File Selection (II) Once the operator has filtered the desired downloadable files, he/she selects the target files and clicks “Start Download" button to perform the download operation. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 171 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Downloading Operations 172 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Data Loading & Configuration SubSystem Description & Operations Downloading Operations Maintenance Downloading - Progress Screen Once the downloadable files, consistent with the filtering criteria, have been selected and the “Start Download" pushbutton has been pressed the download starts and the DLCS provides the operator with progress information. Released in June 15, 2020 TRAINING USE ONLY Training Use Only 173 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual Released in June 15, 2020 TRAINING USE ONLY Training Use Only Data Loading & Configuration SubSystem Description & Operations Downloading Operations 174 / 377 This document shall be used in accordance with the provisions described on the front page. NTCSS Release 2023-01 47_ATA45_Lv2&3_CAT B2_P_JUN20.pdf A400M Training Manual 2.2.4 Data Loading

A400M Training Manual PDF - June 2020

Document Details

Tags

Related

Summary

Full Transcript

Upgrade to continue