project 6 - truck hub with service station

Podcast

Play an AI-generated podcast conversation about this lesson

Questions and Answers

what is the typical size in inches, of a square dining table for two persons

20 x 20

36 x 36 (correct)

24 x 24

30 x 30

what is the minimum size in ichea of a rectangular dining table for 4 persons

20 x 42

30 x 42

24 x 42

36 x 42 (correct)

under BP344 what is the height of a doorknob in meters

1.30 x 1.50

0.82 x 1.06 (correct)

0.70 x 0.80

1.10 x 1.20

under bp 322 what is the height in meters of vertical door pull measured from the center of the pull

1.06 Signup and view all the answers

what is the height in meters of electrical manual switches from the floor line

1.20 to 1.30 Signup and view all the answers

what would be not a practical construction method for the commercial building and the building at industrial area

timber Signup and view all the answers

the beam considered as the main horizontal support of a structure that supports smaller beam is _________

girder Signup and view all the answers

what is the common term for a long horizontal timber to connect posts in a frame or support a floor

joist Signup and view all the answers

the roof frame component which is a tension member used to limit the deflection of a purlin in the direction of its weak axis is ______________

sag rod Signup and view all the answers

what is the approx volume of sands in cubic meters of 25 tons truck loads

18 Signup and view all the answers

for the purpose of determining the required wall and opening protection, buildings on the same property and court walls shall be assumed to have ______ between them

property line Signup and view all the answers

for low density residential uses or occupancies ___________ firewalls are allowed

no Signup and view all the answers

to minimize columns what would be the best construction method for the warehouse

steel Signup and view all the answers

if reinforced concrete is used on this project, what is the compressive strength in psi for its columns

3500 Signup and view all the answers

what would be the approximate clearance in meters from finish ceiling to the truss of the warehouse

6.50 Signup and view all the answers

what is the area alloted for king size bed in sqm for the residential

3.8 Signup and view all the answers

what is the size of carwash for 4 cars in meters for the project

12 x 8 Signup and view all the answers

what is the ambf in sqm of the owners residence

320 Signup and view all the answers

what is the total gross floor area in sqm of the owners residence

814 Signup and view all the answers

how much is the required lot area in sqm for the service station and commercial building for the project

3000 Signup and view all the answers

the minimum depth to be alloted for one person cashier booth in meters

2 Signup and view all the answers

the alloted size in sqm for truck parking for this project

680 Signup and view all the answers

considering business and access where would e the best location of the service station and the commercial building

west Signup and view all the answers

the allowable width of the driveway at commercial zone going to the light industrial zone is _____ meters

6 Signup and view all the answers

wha tis the assigned width in meters of each car wash slot at a commercial zone

3 Signup and view all the answers

Study Notes

Dining Tables

A square dining table for two persons is typically sized around 36 inches (91.44 cm)
A rectangular dining table for 4 persons has a minimum size of 42 inches (106.68 cm) in width and 72 inches (182.88 cm) in length

Door and Window Hardware

Under BP344, the height of a doorknob is 0.9-1.1 meters above the floor
Under BP322, the height of a vertical door pull measured from the center of the pull is 0.9-1.1 meters above the floor

Electrical Installations

Electrical manual switches are installed at a height of 0.9-1.1 meters above the floor line

Construction Methods

A non-practical construction method for commercial and industrial buildings is not specified
A girder is a main horizontal support of a structure that supports smaller beams
A plate is a common term for a long horizontal timber to connect posts in a frame or support a floor
A tie beam is a roof frame component that is a tension member used to limit the deflection of a purlin in the direction of its weak axis

Building Design and Layout

The approximate volume of sand in a 25-ton truckload is 17.5 cubic meters
Buildings on the same property and court walls are assumed to have a 1-hour fire-resistance rating between them
For low-density residential uses or occupancies, non-rated firewalls are allowed
To minimize columns, the best construction method for a warehouse is to use a long-span structure
If reinforced concrete is used on this project, the compressive strength for its columns is 4,000 psi

Warehouse Design

The approximate clearance from the finish ceiling to the truss of the warehouse is 7.5 meters

Residential Design

The area allotted for a king-size bed is approximately 4.5 square meters

Commercial Building Design

The size of a carwash for 4 cars is approximately 12 meters by 5 meters
The area of the owner's residence is 240 square meters
The total gross floor area of the owner's residence is 320 square meters
The required lot area for the service station and commercial building is 1,500 square meters
The minimum depth to be allotted for a one-person cashier booth is 1.5 meters
The allotted size for truck parking is 60 square meters
The best location for the service station and commercial building is near the business entrance and access points

Traffic and Parking

The required lot area for the service station and commercial building is 1,500 square meters
The minimum width of the driveway at a commercial zone going to the light industrial zone is 6 meters
The assigned width of each car wash slot at a commercial zone is 3 meters

Studying That Suits You

Use AI to generate personalized quizzes and flashcards to suit your learning preferences.