Skid Steer Loader Safety PDF

Skid Steer loader Safety Your Name: 1. What should you do when checking the engine oil level? A. Check the owner's manual for guidance B. Look for signs of oil leakage C. Use the gauge on the dashboard D. Wipe the dipstick before checking 2. What should you inspect when checking the a...

Skid Steer loader Safety Your Name: 1. What should you do when checking the engine oil level? A. Check the owner's manual for guidance B. Look for signs of oil leakage C. Use the gauge on the dashboard D. Wipe the dipstick before checking 2. What should you inspect when checking the air induction system? A. The air filter and intake hose connection B. The wheels and tires C. The electrical system components D. The hydraulic oil level and belts 3. What is an important aspect of inspecting the wheels and tires? A. Checking the fuel level B. Verifying the parking brake is holding C. Ensuring mounting nuts are tight and tire inflation is correct D. Inspecting the hydraulic system components 4. What should you check for when inspecting the hydraulic system components? A. Signs of oil leakage B. The condition of the drive belts C. Worn, damaged, or leaking hoses and cylinders D. Proper tire inflation 5. What is an important part of the safety systems inspection? A. Checking the engine oil level B. Inspecting the wheels and tires C. Verifying the parking brake is holding and testing lockouts D. Inspecting the air filter 6. What should you do when checking the coolant level? A. Check the fuel level B. Check the coolant reservoir C. Check the engine oil level D. Inspect the hydraulic oil level 7. What is the primary reason for Blind Spot Awareness in a Skid Steer Loader? A. To reduce fuel consumption while operating B. To improve operator visibility while reversing C. To ensure proper mirror alignment D. To prevent running over people, materials, or striking other vehicles and equipment 8. What is the recommended step to take before reversing a Skid Steer Loader? A. Check your mirrors B. Shoulder check and pause to think C. Look at your camera D. Start reversing immediately 9. Why is eye contact important when using hand signals at a work site? A. To add emphasis to the hand signal B. To distract other workers from the task at hand C. To confirm the other person has understood the signal D. To ensure the signal is visible to everyone 10. What is the purpose of the Three Point Contact rule when entering or exiting a Skid Steer Loader? A. To reduce the risk of falling B. To maintain contact with the loader at all times C. To improve operator balance D. To increase the loader's lifting capacity 11. What is the recommended approach to managing work stress? A. Dismiss near misses as they are rare B. Take regular breaks to reduce stress C. Use the coaching programs and Cognitive Behavioral Therapy D. Don't use cell phones while operating 12. Why is it important to 'Look Above You' when operating a Skid Steer Loader? A. To check for overhead obstructions B. To ensure the loader's bucket is at the correct height C. To observe the surrounding environment D. To monitor the loader's fuel level 13. What is the first step in the Start-Up Procedures? A. Switch the ignition key to the 'on' position B. Check parking brake is engaged C. Shift transmission to 1st gear D. Press the brake and release the parking brake 14. What is the purpose of running the engine for a minimum of 5 minutes? A. To perform an auto self-test B. To check the gauges for proper function C. To permit cooling of the engine D. To allow the oil pressure indicator to light 15. What should be done before shutting down the loader? A. Check the parking brake is disengaged B. Raise the bucket to the highest position C. Shift the gear to 1st position D. Lower the bucket to the ground 16. What is the purpose of greasing the loader? A. To improve the performance of the CB radio B. To check for leaks and damage C. To lubricate the hydraulic system D. To reduce wear and tear on hinges and pins 17. What should be done during the walk-around inspection? A. Check the parking brake is engaged B. Check the beacon is functioning C. Check the hydraulic lockout is engaged D. Check for leaks, vibrations, or unusual noises 18. What should be done after shifting the transmission to 1st gear? A. Turn the wheel and check steering B. Operate the controls to check proper operation C. Press the brake and release the parking brake D. Run the engine at idle speed