Podcast
Questions and Answers
What is the primary reason for inspecting devices under magnification?
What is the primary reason for inspecting devices under magnification?
- To check for stiffness in movable parts
- To detect small pieces of bioburden or debris (correct)
- To inspect for cracks and breakage
- To check for corrosion
What is the purpose of using a diathermy pin point tester?
What is the purpose of using a diathermy pin point tester?
- To inspect for corrosion on devices
- To function test telescopes and light cables
- To check the channel on cannulated devices
- To inspect insulated devices for damaged surfaces (correct)
What should be reported immediately to the supervisor?
What should be reported immediately to the supervisor?
- Devices that are damaged, incomplete, or malfunctioning (correct)
- Devices that are ready for sterilization
- Devices that are dirty but can be cleaned
- Devices that require sharpening
Why is it important to inspect devices for cleanliness?
Why is it important to inspect devices for cleanliness?
What is the purpose of function testing telescopes and light cables?
What is the purpose of function testing telescopes and light cables?
What type of lubricant may be used on devices with non-sticking joints?
What type of lubricant may be used on devices with non-sticking joints?
Why is it essential to check the screws on jointed RMD for tightness?
Why is it essential to check the screws on jointed RMD for tightness?
What is the primary function of a computerized track and trace system in a CSSD?
What is the primary function of a computerized track and trace system in a CSSD?
What is produced automatically once a barcode label is scanned in the IAP room?
What is produced automatically once a barcode label is scanned in the IAP room?
What is the purpose of checking the edges of clamping RMD?
What is the purpose of checking the edges of clamping RMD?
What alternative is available for CSSDs without a computerized track and trace system?
What alternative is available for CSSDs without a computerized track and trace system?
What is the primary reason for conducting a visual inspection of the load prior to reprocessing?
What is the primary reason for conducting a visual inspection of the load prior to reprocessing?
What is the consequence of not disassembling devices prior to manual cleaning?
What is the consequence of not disassembling devices prior to manual cleaning?
What should be done if a small percentage of RMD in a load were not cleaned and/or dried effectively?
What should be done if a small percentage of RMD in a load were not cleaned and/or dried effectively?
What is the purpose of checking for excessive wetness in manually cleaned devices?
What is the purpose of checking for excessive wetness in manually cleaned devices?
What is the consequence of not completing documentation for manually cleaned items?
What is the consequence of not completing documentation for manually cleaned items?
What is the primary reason for selecting a specific operating cycle for a load?
What is the primary reason for selecting a specific operating cycle for a load?
What is the primary requirement for the ventilation in the IAP room?
What is the primary requirement for the ventilation in the IAP room?
What is the recommended temperature range for the IAP room?
What is the recommended temperature range for the IAP room?
What is the purpose of environmental cleaning in the IAP room?
What is the purpose of environmental cleaning in the IAP room?
What is the recommended material for furniture in the IAP room?
What is the recommended material for furniture in the IAP room?
Who should carry out the job in the IAP room?
Who should carry out the job in the IAP room?
What is the classification of the ventilation standard for the IAP room?
What is the classification of the ventilation standard for the IAP room?
What is the primary cause of excessive wetness in a load?
What is the primary cause of excessive wetness in a load?
What should be done if a device is not properly disassembled in the wash area?
What should be done if a device is not properly disassembled in the wash area?
What is the purpose of documenting load contents and non-conformances?
What is the purpose of documenting load contents and non-conformances?
What should be checked after unloading a device?
What should be checked after unloading a device?
What is the consequence of a spray arm rotation being hindered during the wash cycle?
What is the consequence of a spray arm rotation being hindered during the wash cycle?
What is the purpose of local policy checks after unloading a device?
What is the purpose of local policy checks after unloading a device?
Flashcards are hidden until you start studying
