SCBA Daily Inspection Procedures

Podcast

Play an AI-generated podcast conversation about this lesson

Questions and Answers

What should you check first when handling the battery module?

Inspect the battery module for visible damage. (correct)

Check the piezo emitters for functionality.

Ensure the power module is functioning.

Verify that the battery module is securely attached.

Which step is necessary before removing the battery module?

Turn off the power module.

Charge the battery module fully.

Detach the power module.

Unlock the battery module with a removal tool. (correct)

What is the requirement for the connection seal during the inspection?

It must be painted.

It should be dry to the touch.

It can be loose as long as it's present.

It should be present and undamaged. (correct)

What should be inspected on the power module before working with the battery module?

The piezo emitter covers for obstructions. Signup and view all the answers

After reinserting the battery module, what must be done?

Turn off the PASS device. Signup and view all the answers

What indicates a successful inspection of the battery module?

There are no visible damages and the seal is undamaged. Signup and view all the answers

Which of the following is NOT part of the initial inspection process?

Assessing battery life. Signup and view all the answers

What tool is essential for unlocking the battery module?

A battery removal tool. Signup and view all the answers

Which condition must the piezo emitter covers meet?

They must be free of any blockages. Signup and view all the answers

What is the first step in releasing the quick connect from the cylinder valve?

Turn the quick connect counterclockwise a quarter of a turn. Signup and view all the answers

What should be done to ensure a safe connection to the cylinder valve?

Inspect the quick connect fittings for proper operation. Signup and view all the answers

What is the minimum pressure the cylinder should have for proper operation?

4050 PSI or greater Signup and view all the answers

Which part must be checked for visible damage on the control module?

Displays Signup and view all the answers

Before installing the quick connect, what should be ensured about the coupling ends?

They are free of dirt or debris. Signup and view all the answers

What should be ensured about the handgrip during connection to the pressure regulator?

It should rotate approximately 45° counter-clockwise. Signup and view all the answers

What condition should the high pressure relief valve be in?

Free of damage. Signup and view all the answers

What is essential to confirm about the cylinder band's latch?

It opens and closes properly. Signup and view all the answers

What should be verified about the needle and gauge face on the cylinder valve?

The needle should be visible. Signup and view all the answers

What is the primary action that should be taken if SCBA fails any inspection condition?

Remove the SCBA from service. Signup and view all the answers

Which component does NOT require a specific inspection according to the guidelines?

Breathing valve Signup and view all the answers

What should be inspected on the SCBA facepiece?

Lens for cracks and scratches Signup and view all the answers

Which of the following is a requirement for the daily SCBA inspection?

Personnel must inspect their own assigned SCBA. Signup and view all the answers

When should SCBA be inspected after use?

After cleaning and disinfection. Signup and view all the answers

Which condition disallows the inspection of the SCBA?

If there is danger of contacting hazardous contaminants. Signup and view all the answers

What must be ensured regarding the exhalation valve in the facepiece?

It must operate easily and return when released. Signup and view all the answers

What is the correct procedure regarding SCBA straps during inspection?

Inspect for tears, cuts, and wear. Signup and view all the answers

What should be checked in the regulator during inspection?

Presence of moisture or debris. Signup and view all the answers

Study Notes

SCBA Daily Inspection Requirements

SCBA must be inspected daily by personnel; delegation of this responsibility is prohibited.
Inspections occur after proper cleaning and disinfection, avoiding contact with hazardous contaminants.

Inspection Components Overview

The inspection includes a Visual Inspection and a Functional Test.
SCBA must be removed from service if it fails any inspection conditions or functional tests.

Visual Inspection Checklist

Inspect all components for any signs of deterioration, dirt, cracks, debris, tears, holes, or chemical damage.
Evaluate all straps (shoulder pads, lumbar pad, waist straps, facepiece head harness) for any wear or missing parts.

Facepiece Inspection

Check lens for cracks, scratches, deformation, or discoloration.
Verify rubber facepiece for a tight seal against the lens ring.
Ensure the exhalation valve is clean and operational, with proper movement.
Inspect inlet for damage and ensure inhalation valve is properly in place.
Check nosecup for secure fit and proper function of check valves.

Regulator Inspection

Ensure no moisture or debris is present, especially in regulator and microphone ports.
Confirm o-ring and seal ring are intact and free from damage.
Inspect quick connect hose for signs of deterioration and ensure fittings are clear of debris.

Pressure Reducer Inspection

Confirm quick connect fittings operate correctly and securely.
Clean the male and female ends of the coupling before installation.
Ensure high-pressure relief valve is undamaged and handwheel is reattached correctly.
Verify proper alignment of the bell and that screws are tight.

Cylinder and Valve Assembly

Check hydrostatic test date on approval sticker located on the cylinder neck.
Ensure visibility of the needle and gauge face, and ensure the gauge stem is straight.
Confirm the presence of the rubber boot on the cylinder valve.
Ensure cylinder pressure is at 4050 PSI or greater.

Carrier Assembly Inspection

Test latch operation on the cylinder band for proper functionality and security.
Ensure Unit Identifier is present.
Confirm lumbar pad is securely attached.
Check power module and pressure reducer for secure attachment to the backplate.

Control Module Inspection

Inspect displays for visible damage or cracks.
Ensure buttons are intact and not missing.
Verify secure attachment of the hose assembly to the control module.
Ensure gauge needle and face are visible and gauge stem is straight.

Power Module & Battery Module Inspection

Confirm secure attachment of power module and battery module to the backplate.
Inspect piezo emitters for obstruction due to dirt or debris.
Use battery removal tool to unlock and remove the battery module.
Examine battery module for visible damage and ensure connection seal is intact.
Reinsert battery module and disable the PASS device after checking.

Studying That Suits You

Use AI to generate personalized quizzes and flashcards to suit your learning preferences.

Description

This quiz focuses on the daily inspection requirements for Self-Contained Breathing Apparatus (SCBA). It includes necessary visual and functional inspection components that must be evaluated to ensure safety. Understanding these procedures is essential for personnel responsible for SCBA maintenance.