RMS Map Output and Volumetrics Quiz

The 'General' tab in the Volumetrics dialog box is used to set up the volumes to be calculated. It allows the user to define a zone as the thickness between two horizons and specify a job to perform volume calculations and report on a subset of the grid model.

The 'Output Type' field in the 'General' tab allows the user to input a prefix that will be used for all output parameters, zone maps, and total maps.

The attributes defined in the region model can be used to populate settings in the 'Variables' tab of the dialog box. The region names populated from the region model can be utilized for this purpose.

<p>In the Volumetrics dialog box, a zone is defined as the thickness between two horizons.</p> Signup and view all the answers

<p>Click the Run button in the Volumetrics dialog box for the current project realization, or click Save to save the settings as a job, include the job in a workflow, and then run the workflow.</p> Signup and view all the answers

<p>RMS displays a progress indicator pop up box when calculating the volumes.</p> Signup and view all the answers

<p>A warning message about overwriting a report file appears if a specified volumetrics report file already exists.</p> Signup and view all the answers

<p>Document list or Tabular layout</p> Signup and view all the answers

<p>Text file with a separate file for each realization</p> Signup and view all the answers

<p>Excel, CSV, or text file with a separate file for each realization</p> Signup and view all the answers

<p>Including realization number in file name and exporting parameter units to file</p> Signup and view all the answers

<p>Based on the subsets specified</p> Signup and view all the answers

<p>Creates a table within RMS with results for all realizations, useful for investigating uncertainty</p> Signup and view all the answers

<p>Three tabs: Data selection, Statistics, and Raw data</p> Signup and view all the answers

<p>High and low side estimates, respectively</p> Signup and view all the answers

<p>The calculated volumetric data in a table, accounting for potential undefined values if the job is run for fewer realizations than set for the project</p> Signup and view all the answers

<p>The required Import/Export unit set has been selected</p> Signup and view all the answers

<p>Oil/Condensate, Gas, and Totals</p> Signup and view all the answers

<p>Bulk, Net, Pore, HCPV, STOIIP, GIIP, and Recoverable</p> Signup and view all the answers

<p>Porosity, water saturation, and recovery factors</p> Signup and view all the answers

<p>Three: Parameter, Zone map, and Total map</p> Signup and view all the answers

<p>Pre-calculated bulk volume</p> Signup and view all the answers

<p>Per license boundary or per zone</p> Signup and view all the answers

<p>Discrete fluid parameter</p> Signup and view all the answers

<p>Set to zero or allowed, providing a choice to check the results</p> Signup and view all the answers

<p>By dragging a surface into the Map Layout drop site</p> Signup and view all the answers

<p>Output location</p> Signup and view all the answers

<p>A closed, non-collapsed polygon</p> Signup and view all the answers

<p>Parameter drop-down list</p> Signup and view all the answers

<p>Model QC, General 2D data, Clipboard, and Zones</p> Signup and view all the answers

<p>By providing a smaller value for more accurate maps but slower calculations</p> Signup and view all the answers

<p>In the Variables tab, depending on the options selected in the Calculations tab</p> Signup and view all the answers

<p>Panel, Table, and Region model</p> Signup and view all the answers

<p>By defining it with a template based on standard contacts</p> Signup and view all the answers

<p>In the Variables tab, with options depending on the input and calculations chosen in previous tabs</p> Signup and view all the answers

<p>By selecting a variable class, specific variable, and subsets for which different variable values are given</p> Signup and view all the answers

<p>Oil, gas, and formation variables</p> Signup and view all the answers

<p>Through constant values, surface or parameter selection, or by using a table with the same format as specified in the Table Link section of the Volumetrics dialog box</p> Signup and view all the answers

<p>In the Report file tab</p> Signup and view all the answers

<p>To the units set for STOIIP and GIIP respectively, specified in the Unit Set Selector dialog box</p> Signup and view all the answers