RMS Map Output and Volumetrics Quiz

The General tab is used to set up the volumes to be calculated and define zones.

A job can be specified by selecting the zone or zones to be used.

The Region Index allows the selection of a discrete parameter defining a region partition.

<p>Attributes defined in the region model can be used to populate settings in the Variables tab of the dialog box.</p> Signup and view all the answers

<p>Click the Run button in the Volumetrics dialog box for the current project realization, or click Save to save the settings as a job, include the job in a workflow, and then run the workflow.</p> Signup and view all the answers

<p>A warning message is displayed asking if you want to overwrite the previous report file.</p> Signup and view all the answers

<p>A warning is displayed indicating that the specified table object already exists but was generated using a different job specification.</p> Signup and view all the answers

<p>Document list output is a text file with a separate file for each realization, while Tabular output is presented as an Excel, CSV, or text file with a separate file for each realization.</p> Signup and view all the answers

<p>Options such as including realization number in file name and exporting parameter units to file can be toggled.</p> Signup and view all the answers

<p>The order of volume calculations in the Report file can be set based on the subsets specified.</p> Signup and view all the answers

<p>The Report table option creates a table within RMS with results for all realizations, useful for investigating uncertainty.</p> Signup and view all the answers

<p>The Volumetric Table Viewer dialog box consists of three tabs: Data selection, Statistics, and Raw data.</p> Signup and view all the answers

<p>P10 and P90 values in the Statistics tab reflect high and low side estimates, respectively.</p> Signup and view all the answers

<p>Raw data tab presents the calculated volumetric data in a table, accounting for potential undefined values if the job is run for fewer realizations than set for the project.</p> Signup and view all the answers

<p>Before running the job, ensure the required Import/Export unit set has been selected for the report output.</p> Signup and view all the answers

<p>Oil/Condensate, Gas, and Totals</p> Signup and view all the answers

<p>Bulk, Net, Pore, HCPV, STOIIP, GIIP, and Recoverable</p> Signup and view all the answers

<p>Porosity, water saturation, and recovery factors</p> Signup and view all the answers

<p>Three: Parameter, Zone map, and Total map</p> Signup and view all the answers

<p>Pre-calculated bulk volume</p> Signup and view all the answers

<p>Area and average thickness</p> Signup and view all the answers

<p>Discrete fluid parameter</p> Signup and view all the answers

<p>Setting them to zero or allowing them</p> Signup and view all the answers

<p>By dragging a surface into the Map Layout drop site</p> Signup and view all the answers

<p>Output location</p> Signup and view all the answers

<p>A closed, non-collapsed polygon</p> Signup and view all the answers

<p>Parameter drop-down list</p> Signup and view all the answers

<p>Maps in RMS can be output to specific folders in the Data tree including Model QC, General 2D data, Clipboard, and Zones. Outputting maps to Zones requires a network structural framework for grid model based output.</p> Signup and view all the answers

<p>The map increment option in RMS allows users to adjust grid resolution for output maps. A smaller value provides more accurate maps but slower calculations.</p> Signup and view all the answers

<p>Input variables for select volumes in RMS are entered in the Variables tab, depending on the options selected in the Calculations tab.</p> Signup and view all the answers

<p>Variables can be defined for each zone, region, or as a single value for all zones and regions through three alternative input sources: Panel, Table, and Region model.</p> Signup and view all the answers

<p>Fluid contact data from a region attribute table can be used in Volumetrics in RMS if defined with a template based on standard contacts.</p> Signup and view all the answers

<p>The Variables tab in RMS lists the formulas to be used for selected calculations, with options depending on the input and calculations chosen in previous tabs.</p> Signup and view all the answers

<p>Users can specify variables by selecting a variable class, specific variable, and subsets for which different variable values are given.</p> Signup and view all the answers

<p>Variable types in RMS include oil, gas, and formation variables, each with specific variables and unit measures, defined through the Unit Set Selector in the Tools menu.</p> Signup and view all the answers

<p>Variables used as input to volume calculations can be specified in RMS through constant values, surface or parameter selection, or by using a table with the same format as specified in the Table Link section of the Volumetrics dialog box.</p> Signup and view all the answers

<p>In the Report file tab in RMS, users can specify the output as a Report file or a Report table data object, with calculated values in units taken from the Import/Export unit set, allowing generation of reports in specified units.</p> Signup and view all the answers

<p>Associated gas and liquid units in the Report file and table in RMS are linked to the units set for STOIIP and GIIP respectively, which are specified in the Unit Set Selector dialog box accessed from the RMS menu bar under Tools.</p> Signup and view all the answers