2w151B CDC Mastery Flashcards
100 Questions
101 Views

Choose a study mode

Play Quiz
Study Flashcards
Spaced Repetition
Chat to Lesson

Podcast

Play an AI-generated podcast conversation about this lesson

Questions and Answers

What type of flare magazines do F-15 and F-16 aircraft use?

  • MJU-15
  • MJU-12 (correct)
  • MJU-10
  • MJU-20

What does a complete cluster bomb unit (CBU) consist of?

A quantity of small submunitions and a dispenser.

What is a normal round with the primer and propellant charge removed called?

Dummy round.

What characteristic allows a rotary-based gun system to achieve a higher rate of fire?

<p>All steps of the firing cycle take place simultaneously.</p> Signup and view all the answers

What is a typical operating range for time fuzes?

<p>5 to 92 seconds.</p> Signup and view all the answers

Which aircraft can deploy AN/ALE-50 decoys?

<p>All of the above (D)</p> Signup and view all the answers

What holds the AGM-65 missile on the LAU-88 launcher during flight?

<p>Shear pin.</p> Signup and view all the answers

What bomb does all GBU-12 models use as a warhead?

<p>MK-82.</p> Signup and view all the answers

What color are all naval mine casings painted?

<p>Gold.</p> Signup and view all the answers

What does aluminum's formation of a tightly adhering oxide film provide?

<p>Increased resistance under mild corrosive conditions.</p> Signup and view all the answers

Why should ammunition never be needlessly subjected to sunlight?

<p>Prolonged exposure to heat will affect its ballistics.</p> Signup and view all the answers

At what stage is detecting and treating corrosion most important?

<p>Earliest.</p> Signup and view all the answers

What kind of munitions do operators not need to be near during practice loading?

<p>Inert training munitions.</p> Signup and view all the answers

How will magnesium always appear?

<p>Primed and top coated.</p> Signup and view all the answers

What basic system functions are contained in the analog stores management system?

<p>Arming, release, and weapons selection.</p> Signup and view all the answers

What must be ensured before operating bomb bay door systems for checkout?

<p>All personnel and equipment have been cleared from the area of operation.</p> Signup and view all the answers

What must be ensured before connecting or disconnecting a high-pressure service hose?

<p>The system is not pressurized.</p> Signup and view all the answers

What do built-in-test (BIT) units in rail launchers automatically check for?

<p>Proper voltage tolerances in the launcher electrical units.</p> Signup and view all the answers

What does changing the position of the MJ-1/B accelerator pedal do?

<p>Varies the flow rate of the pump in the hydrostatic drive.</p> Signup and view all the answers

How many rounds do the ammunition boxes of the link-fed system normally hold?

<p>100 to 4,500 rounds.</p> Signup and view all the answers

How is the parking brake set on the MHU-83?

<p>Controlled by a locking valve located to the left of the steering wheel.</p> Signup and view all the answers

What is the engine of the MHU-83 series lift trucks?

<p>Air-cooled, 25.2-horsepower, diesel engine.</p> Signup and view all the answers

What is the maximum fuel filling level for an unmodified A/M32A-95 fuel tank?

<p>1/2.</p> Signup and view all the answers

When is a concurrent servicing supervisor (CSS) not required?

<p>When fueling is not being performed.</p> Signup and view all the answers

What servicing action cannot be performed while refueling?

<p>Oxygen.</p> Signup and view all the answers

What action is required during an operator's pre-use inspection of aerospace ground equipment (AGE)?

<p>Cycle the unit completely through its range of capabilities.</p> Signup and view all the answers

What is the speed during ground rotation of the multipurpose rotary launcher?

<p>1/8 normal rotation speed.</p> Signup and view all the answers

Where does the ammunition loading assembly (ALA) get its power during normal loading of the A-10 gun system?

<p>The aircraft's hydraulic system.</p> Signup and view all the answers

What component retains the arming wire during release for the B-11 bomb shackle?

<p>Arming hook.</p> Signup and view all the answers

What happens when the cocking pin is released from the cam at the sear point during the GAU-8 30 mm gun firing cycle?

<p>The firing pin spring drives the firing pin forward to detonate the primer of the round.</p> Signup and view all the answers

What is the travel limit of the tow bar of the MHU-204/M and MHU-196/M lift trailers during towing?

<p>45 degrees.</p> Signup and view all the answers

Why must kinetic energy penetrator munitions be handled carefully?

<p>Many of their delivery systems contain explosives or other hazardous components.</p> Signup and view all the answers

What is the usage of 'Y' stands?

<p>To support munitions temporarily.</p> Signup and view all the answers

What is the usage of load binders?

<p>To secure the load to the table or loading adapter.</p> Signup and view all the answers

What is the usage of the 36-inch adapter?

<p>To load internal and external stores on the B-52 aircraft.</p> Signup and view all the answers

What is the usage of a gantry stand?

<p>To support TERs temporarily.</p> Signup and view all the answers

Under what circumstances may fighter aircraft be exempted from the 50-foot distance placement requirements of an auxiliary power unit (APU)?

<p>During combat or simulated combat operations.</p> Signup and view all the answers

Where do trailers get electrical power to illuminate their brake lights?

<p>From the trailer's intervehicular harness.</p> Signup and view all the answers

From which side of an aircraft should you fight a fire when possible?

<p>Upwind.</p> Signup and view all the answers

How long do general-purpose bombs normally detonate after being engulfed in flames?

<p>Two to four minutes.</p> Signup and view all the answers

High-explosive (HE) bombs are classified according to what?

<p>Kill mechanism or designed use.</p> Signup and view all the answers

How are bomb fuzes classified?

<p>Position and method of arming.</p> Signup and view all the answers

How are the ammunition cans of link-fed systems normally loaded and unloaded?

<p>By hand.</p> Signup and view all the answers

How are the cantilever lift arms operated on the MJ-1B?

<p>By controls at the driver's position or controls directly behind the cradle.</p> Signup and view all the answers

How are the guidance canards of the AIM-9 L/M missiles controlled?

<p>Electrically.</p> Signup and view all the answers

How are the pitch valves set on a BRU-61/A bomb rack?

<p>Manually.</p> Signup and view all the answers

What does corrosion appear on nickel or chrome plated steel surfaces?

<p>Small spots on the plated surfaces.</p> Signup and view all the answers

How does the accelerator pedal change the speed of the MJ-1B lift truck?

<p>Changing the pedal position varies the flow rate of the hydraulic pump.</p> Signup and view all the answers

How far from the supported aircraft should the A/M 32C-10 air conditioner be positioned for optimum unit operating efficiency and safety?

<p>15-30 feet.</p> Signup and view all the answers

How is the GAU-2 automatic gun driven?

<p>Electrically.</p> Signup and view all the answers

How is the LAU-131 rocket pod safed?

<p>Electrically with a shorting pin.</p> Signup and view all the answers

How is the mechanical ram assembly (MRA) primarily controlled and operated?

<p>The lift truck's remote control unit.</p> Signup and view all the answers

How is the remote control attached to the lift truck?

<p>Flexible electrical cord.</p> Signup and view all the answers

How long must the lights of a FL-1D floodlight be left off before you should restart them?

<p>10-15 minutes.</p> Signup and view all the answers

How many AN/ALE-50 decoys can the B-1 carry?

<ol start="8"> <li></li> </ol> Signup and view all the answers

How many MK-82 500-pound bombs can be carried by the bomb rack assembly?

<ol start="20"> <li></li> </ol> Signup and view all the answers

How many RR196/AL chaff bundles may be loaded in the ALE-52 magazines used in the F-22?

<ol start="18"> <li></li> </ol> Signup and view all the answers

How many arming solenoids are normally found on gas-operated bomb racks?

<p>Three.</p> Signup and view all the answers

How many different gun scavenge designs are used on aircraft?

<p>Two.</p> Signup and view all the answers

How many different outputs can an A/M 32A-60 generator provide?

<p>Three.</p> Signup and view all the answers

How many flare magazines can be loaded on the F-22?

<ol start="6"> <li></li> </ol> Signup and view all the answers

How many flares are contained in the SUU-25 flare dispenser?

<ol start="8"> <li></li> </ol> Signup and view all the answers

How many fluid temperature modes are available in the polyalphaolefin (PAO)/ air cooling cart?

<p>Two.</p> Signup and view all the answers

How many hand brake levers are located on the MHU-226/M munitions handling trailer?

<p>Two.</p> Signup and view all the answers

How many inches high is the mechanical ram assembly (MRA) when fully extended?

<ol start="83"> <li></li> </ol> Signup and view all the answers

How many inches is the maximum lift height when the adapter assembly is inverted on the MHU-83 series lift truck?

<p>107.5.</p> Signup and view all the answers

How many inches is the suggested lug spacing for conventional bombs weighing up to 1000 pounds?

<ol start="14"> <li></li> </ol> Signup and view all the answers

How many insertion markings constitute the end of service life for impulse cartridges used in breeches with spring-loaded firing pins?

<p>No limit.</p> Signup and view all the answers

How many instrument/control panels must the operator check during operation of the A/M 32A-86 generator set?

<p>Three.</p> Signup and view all the answers

How many main rail assemblies can be installed on the deck of the MHU-110/M trailer?

<ol start="6"> <li></li> </ol> Signup and view all the answers

How many munitions can the BRU-61/A bomb rack carry?

<p>Four.</p> Signup and view all the answers

How many operators are required to be present during the operation of the -10 air conditioner?

<p>Two.</p> Signup and view all the answers

How many pounds is the lift capacity of the MJ-1 lift truck with aluminum rollers installed?

<ol start="3000"> <li></li> </ol> Signup and view all the answers

How many pounds is the lift capacity of the mechanical ram assembly (MRA)?

<ol start="5000"> <li></li> </ol> Signup and view all the answers

How many pounds is the lifting capacity of the sling assembly used on lift trucks or forklift adapters?

<ol start="4600"> <li></li> </ol> Signup and view all the answers

How many pounds per square inch (psi) is the maximum air pressure you may use for cleaning equipment or work areas?

<p>30 psi.</p> Signup and view all the answers

How many rounds of ammunition is the capacity of the 20mm linkless ammunition loading systems (LALS)?

<ol start="2100"> <li></li> </ol> Signup and view all the answers

How many steps are there in the M240 machine gun cycle of operation?

<ol start="8"> <li></li> </ol> Signup and view all the answers

How many trolleys and chocks can be installed on the deck of the MHU-110 trailer and what is their purpose?

<p>24 trolleys and 48 chocks (with tie-down straps) to accommodate a variety of munitions.</p> Signup and view all the answers

How many trolleys and chocks can the MHU-110/M trailer be configured with for round-shaped stores?

<p>24 trolleys and 48 chocks.</p> Signup and view all the answers

How may the operator verify the fluid level in the lubricating oil tank of the A/M32A-95?

<p>Through the sight glass.</p> Signup and view all the answers

How much air pressure is produced by the MC-2A air compressor?

<p>15 cfm at 200 psi.</p> Signup and view all the answers

How much air pressure must be in the compressor tank before loading with the MHU-196/M trailer?

<p>90 psi.</p> Signup and view all the answers

How much air pressure must be maintained in the air tank before loading with the MHU-204/M and MHU-196/M lift trailers?

<p>MHU-204/M, 105 PSI minimum and MHU-196/M, 90 PSI minimum.</p> Signup and view all the answers

How often are operational and functional checks normally done?

<p>30 or 60 days.</p> Signup and view all the answers

How would you best describe the typical analog system?

<p>Hardwired.</p> Signup and view all the answers

If hydraulic fluid comes in contact with your eyes during a MJ-2A hydraulic test stand operation, what should you do?

<p>Flush eyes with water and seek medical attention.</p> Signup and view all the answers

If the split-deck maintenance platform's tape switches detect an obstruction during an operation, what will the switches stop on the unit?

<p>Forward drive, platform extension, and lowering capabilities.</p> Signup and view all the answers

If you find breech cartridge retainers installed, safety wired, or sealed this certifies that the:

<p>Impulse cartridges are not installed.</p> Signup and view all the answers

In a fault isolation system using built-in test (BIT) checks, the results of the test should narrow the fault down to:

<p>Subsystem or system.</p> Signup and view all the answers

In addition to a 5 gallon container of clean water and butyl rubber gloves, what must be available at a loading site where practice bombs with CXU-1/B spotting charges are being loaded?

<p>Protective mask.</p> Signup and view all the answers

In case of a malfunction, which bomb marking might require documentation on the AF Form 2434?

<p>Lot number and serial number.</p> Signup and view all the answers

In digital stores management systems, what component acts as a multiplex terminal for signals being sent to or coming from weapons stations?

<p>An interface unit.</p> Signup and view all the answers

In gas-operated, single-barrel automatic guns, the force from the expansion chamber is transferred to the bolt face by the:

<p>Operating rod.</p> Signup and view all the answers

In what loading step is the serviceability of the munition loading stations determined?

<p>Aircraft preparation.</p> Signup and view all the answers

In what position must the FL-1D floodlight's platform be placed during towing?

<p>Lower completely.</p> Signup and view all the answers

Independent operation of either lift arm mechanism on the MHU-196/M lift trailer results in:

<p>Rolling the load.</p> Signup and view all the answers

Into how many parts is the GAU-8/A 30mm gun rotor assembly divided?

<p>Two.</p> Signup and view all the answers

List the everyday 2w1X1 uses of air compressors.

<p>To cycle gun systems and ammunition loaders, to power pneumatic tools, to provide compressed air for cleaning and drying components, to recharge pneumatic systems and associated components on aircraft or equipment such as lift trailers.</p> Signup and view all the answers

Name the three components of the hydrostatic drive system.

<ol> <li>Fluid coupling. 2. Variable displacement hydraulic pump. 3. A fixed displacement motor.</li> </ol> Signup and view all the answers

Flashcards

MJU-12 flare magazine use

Used by F-15 and F-16 aircraft to store flares.

CBU (Cluster Bomb Unit)

A cluster bomb unit has small submunitions and a dispenser.

Dummy round

A standard round with the primer and propellant removed.

Rotary-based gun systems

Achieve high rates of fire because all steps happen at once.

Signup and view all the flashcards

Time fuze range

Typical operating range is 5 to 92 seconds.

Signup and view all the flashcards

GAU-8 30mm firing cycle

The firing pin spring activates when cocking pin is released.

Signup and view all the flashcards

AN/ALE-50 decoys

Deployable by F-16 and B-1 aircraft for defense.

Signup and view all the flashcards

AGM-65 missile launcher

Securing the missile with a shear pin on the LAU-88 launcher.

Signup and view all the flashcards

GBU-12 warhead

Uses MK-82 bombs as warhead.

Signup and view all the flashcards

Navel mine casing color

Painted gold for identification.

Signup and view all the flashcards

Aluminum's corrosion resistance

Aluminum's oxide film protects it from mild corrosion.

Signup and view all the flashcards

Ammunition sunlight protection

Shield ammunition from sunlight to prevent heat damage.

Signup and view all the flashcards

Corrosion control strategy

Prioritizes early detection and treatment.

Signup and view all the flashcards

Concurrent servicing supervisor

Unnecessary if fueling is not involved.

Signup and view all the flashcards

MHU-83 lift truck power

Powered by an air-cooled, 25.2-horsepower diesel engine.

Signup and view all the flashcards

MJ-1 lift truck capacity

3,000 pounds lifting capacity with aluminum rollers.

Signup and view all the flashcards

MRA maximum lift height

83 inches maximum lift height.

Signup and view all the flashcards

MHU-110/M trailer capacity

Accommodates 24 trolleys and 48 chocks.

Signup and view all the flashcards

A/M32A-86 generator checks

Requires checks on three instrument/control panels each operation.

Signup and view all the flashcards

High-pressure hose connection

Ensure the system is not pressurized before connecting hoses.

Signup and view all the flashcards

Temporary munitions support

Y stands are used for temporary support, while load binders secure them.

Signup and view all the flashcards

Study Notes

Flares and Munitions

  • F-15 and F-16 aircraft utilize MJU-12 flare magazines.
  • A complete cluster bomb unit (CBU) comprises small submunitions and a dispenser.
  • A dummy round is a standard round with primer and propellant removed.

Gun Systems and Ammunition

  • Rotary-based gun systems achieve higher rates of fire as all firing cycle steps occur simultaneously.
  • Typical operating range for time fuzes is between 5 to 92 seconds.
  • The GAU-8 30mm gun firing cycle involves a firing pin spring activating when the cocking pin is released.

Aircraft Systems and Components

  • AN/ALE-50 decoys can be deployed by F-16 and B-1 aircraft.
  • The AGM-65 missile is secured on the LAU-88 launcher by a shear pin.
  • All GBU-12 models utilize MK-82 bombs as their warhead.

Corrosion Control and Equipment Handling

  • Navel mine casings are painted gold for identification.
  • Aluminum's oxide film enhances its resistance to mild corrosive conditions.
  • Ammunition should be shielded from sunlight to avoid heat-induced ballistic impact.

Ground Equipment and Safety Protocols

  • Corrosion control management prioritizes detection and treatment at the earliest stage.
  • During concurrent servicing, a concurrent servicing supervisor is unnecessary if fueling is not conducted.
  • Air-cooled, 25.2-horsepower diesel engines power MHU-83 lift trucks.

Weight and Capacity Specifications

  • The MJ-1 lift truck with aluminum rollers has a lifting capacity of 3,000 pounds.
  • The maximum lift height of the mechanical ram assembly (MRA) is 83 inches.
  • MHU-110/M trailers can accommodate 24 trolleys and 48 chocks for various munitions.

Operational Procedures

  • Each operation of the A/M32A-86 generator set requires checks on three instrument/control panels.
  • Before connecting high-pressure service hoses, ensure the system is not pressurized.
  • Use "Y" stands to temporarily support munitions, whereas load binders secure loads to the table.

Safe Loading Practices

  • A/M32A-95 fuel tanks should not exceed half full due to fuel expansion properties.
  • The parking brake on the MHU-83 is set using a locking valve and service brake pedal.
  • The FL-1D floodlight needs a 10-15 minute cooldown period before restarting.

Miscellaneous Facts

  • High-explosive bombs are categorized based on their kill mechanism or designed use.
  • Built-in test units in rail launchers monitor proper voltage tolerances.
  • AIM-9 L/M missile guidance canards are controlled electrically, and pitch valves on bomb racks are adjusted manually.

Towing and Aircraft Maintenance

  • A tow bar's travel for MHU-204/M and MHU-196/M lift trailers is limited to 45 degrees.
  • The air conditioner A/M32C-10 should be positioned 15-30 feet away from aircraft for optimal performance.
  • During loading, serviceability of munitions loading stations is evaluated in the aircraft preparation step.

Environmental Considerations

  • General-purpose bombs typically detonate within two to four minutes after exposure to flames.
  • Operators must verify fluid levels in lubrication systems via sight glasses during maintenance checks.
  • Avoid exceeding 30 psi during cleaning equipment or work areas to maintain safety.

Emergency Protocols

  • Flush eyes with water and seek medical attention if hydraulic fluid contacts them during equipment operations.
  • Documentation of bomb markings should include lot numbers and serial numbers in case of malfunctions.
  • Safety measures require two operators present during the use of the -10 air conditioner for safe operation.

Instrumentation and Testing

  • Fault isolation systems utilize built-in tests to identify issues down to a subsystem level.
  • The M240 machine gun cycle of operation consists of eight distinct steps.
  • The mechanical ram assembly (MRA) has a lifting capacity of 5,000 pounds, ensuring heavy-duty operation capabilities.

Studying That Suits You

Use AI to generate personalized quizzes and flashcards to suit your learning preferences.

Quiz Team

Description

Test your knowledge with these flashcards designed for the 2w151B CDC mastery. This quiz covers various terms and definitions related to aircraft munitions and systems. Perfect for aviation enthusiasts and military personnel looking to enhance their expertise.

More Like This

Aviation Instruments Definitions Quiz
13 questions
Aviation Regulations and Safety Quiz
31 questions
Aviation History Quiz
34 questions
Use Quizgecko on...
Browser
Browser