Hand Tools and Equipment Guide PDF

SNO QUESTION OPT A OPT B OPT C OPT D OPYT EANSWER 1 In BEU all menu are accessible to the operator except the ?...

SNO QUESTION OPT A OPT B OPT C OPT D OPYT EANSWER 1 In BEU all menu are accessible to the operator except the ? CV management power problem media problem A&C A 2 Without a power supply BEU can operate. TRUE FALSE F 3 LEU can handle how many streams. 4 2 1 6 B A metalic cover is provided to BEU (SSD-99000) to prevent -------------- activation of the 4 Intentional Unintentional Damage Brocken B switch 5 Best environment for installation of BEU is ____________. Moisture free Dusty Hot free Very cold A 6 Never press the CV KILL push button while the BEU (SSD-99000) is powered _____. On Off Rest Operation A 7 The fuse of BEU(SSD-99000) blows if an internal circuit ------------ occurs Overload Open Low volts High volts A 8 Mode of operation of BEUis? Plain Special Cypher A&C D 9 Operating voltage of BEU is? -20 v +48 v 220 -48 v D 10 BEU equipment is? Cypher equipment Power equipment Measuring equipmen Splash proof A 11 The low BATTERY LEDs mounted on the front panel of BEU are________ in number 1 2 7 4 C 12 BEU can be operate in __________ mode. 2 3 4 1 A 13 BEU is a ________________. Exchange Transceiver set Securing set None of them C 14 In BEU loop test verifies encryption / decryption hardware. TRUE FALSE F 15 BEU contain microprocessor. TRUE FALSE T Which type of screw driver makes work possible in restricted places where common 16 Spiral Ratchet Screw Driver Common Screw Driver Off-Set Screw Driver Cross Point Screw Driver C type screw driver cannot be used ? 17 To remove the components from a circuit , tools used include Soldering Irons Soldering Sucker Soldering Station ALL ARE CORRECT D 18 Proper rating Soldering station is required to be used TRUE FALSE T 19 Temprature can be adjusted on Soldering Irons Soldering Sucker Soldering Station ALL ARE CORRECT C 20 To clean a joint in circuit, ____ is used Soldering Irons Soldering Sucker Soldering Station Soldering Flux D Which type of tool kit is maintained by specialist shops to meet their peculiar hand tool 21 Class "C" Class "A" Class "B" All are correct A requirments ? 22 Which type of tool kit is issued to individual trademan ? Class "C" Class "A" Class "B" All are correct B 23 Which type of tool kit is kept in section lockups ? Class "C" Class "A" Class "B" All are correct C 24 Hand tool kits are divided into how many classes for effective utilization ? 2 3 4 5 B 25 Crimping Tool is a.? Special Tool Common Tool Electrict tool non is correct A 26 Which tool is used to make RJ-9connector? Crimping Tool Plier Flat Nose Punching Tool Screw Driver A Which type of pliers are most common typeof pliers and used for holding as well as 27 Combination Pliers Diagonal Cutting Pliers Flat Nose Pliers Round Nose Pliers A cutting small wires ? 28 Which tool is used to make RJ-45 connector? Plier Flat Nose Crimping Tool Side Cutter Punching Tool B 29 Which tool is used to make RJ-11 connector? Plier Flat Nose Crimping Tool Punching Tool Screw Driver B 30 Digital Multi Meter can measure Ac voltages upto? 1000v 220v 380 v 600v A 31 Digital Multi Meterfluke 177 can measure ------ Frequency Peak power RMS voltage attenuation A 32 Battery used in Digital Multi Meterfluke 177 is? 24VDC 12VDC 9VDC 1.5VDC C 33 Digital Multi Metercan measure DC voltages upto ? 380 v 1000v 220v 600v B 34 Length of green test lead is? 5 meter 50meter 20 meter 15 meter A 35 Leads used with earth tester are ? 3 2 4 5 A 36 Earth tester can measure earth resistance upto? 2kohm 10 ohm 20ohm 30 ohm A 37 Earth tester is used to measure ? current resistance voltage Peak power B 38 Which tools are used for tightening or removing nuts and bolts ? Pliers Common Screw Drivers Chisels Wrenches D 39 Network cable tester SC8108-A uses 12 volt DC power supply ? TRUE FALSE F If not in use , network cable tester SC8108-A shuts down automatically after a period of 40 1 HOUR 45MIN 30MIN 15MIN C ? It is recommended that never try to connect or start the network cable tester with any 41 TRUE FALSE T power supply other than the tester itself. 42 Network cable tester sc8108-a calibration is carried out? User Level Company Level PMEL 107 NONE IS CORRECT A 43 Ohm Meter is used to check? Resistance Current Watt Joul A 44 Resistance can be checked through? Earth Tester Current Meter Ohm Meter a & care correct D 45 DMMcan be used as? Oham meter Meggar Annalayzer Signal Generator A 46 Tester OHM meter can be useas an? Ampere meter Signal Generator DMM non is correct D 47 Temperature of rubber store is to be maintained –5 to 25°C (for A/C tyres & tubes). TRUE FALSE T 48 Oil need to be splashed in rubber store. TRUE FALSE F Which type of wrench has one jaw fixed and the other can be moved by the thumb screw 49 Ratchet Wrench Handle Adjustable Wrenche Open End Wrenches Combination Wrenches B or spiralworm screw adjustment on the handle ? 50 As a classification of fire, Rubber Fire is classified as ? Liquid Solid Electric All are correct A Wooden plank is use to avoid Rubber mate is useto avoid Plastic sheet is useto avoid 51 As isolation………… Woolen cloth is use B electric shock electrict shock electrict shock 52 For safe operation of oscilloscope chassis should not remain at ground TRUE FALSE F 53 We use ____________ to check the DC Power supplies ripple & noise Test procedure Cable Tester Electronic Level Oscilloscope Spectrum Analyzer C 54 One of the following can naot be check with oscilloscope voltage resistance pules shape ripples B 55 It can measure noise and ripples of a DC power supply Cable Tester Electronic Level Oscilloscope Spectrum Analyzer C 56 DMM can measure Ac voltages upto? 1000v 220v 380 v 600v A 57 DMM fluke 177 can measure ------ Frequency Peak power RMS voltage attenuation A 58 Battery used in DMM fluke 177 is? 24VDC 12VDC 9VDC 1.5VDC C 59 DMM can measure DC voltages upto ? 380 v 1000v 220v 600v B 60 It is designed to serve the tradesmen, the same way as pencil or pen is known as …… Scriber Wire Gauge Calipers Fitter Square A 61 Power meter is used to measure _______ RF power DC power AC power None A 62 Power sensor is used with _______ DMM Power Meter Clamp Meter Ohm Meter B 63 Always use power sensor with Power meter. TRUE FALSE T 64 Soft Keys on power meter are used to give Fix function frequency not used random Function D In spectrum analyzer, Start frequency is set to____MHz while measuring RF Power from 65 1200 1600 1700 1800 A RF Amplifier In spectrum analyzer, Stop frequency is set to____MHz while measuring RF Power from 66 200 300 400 1400 D RF Amplifier In spectrum analyzer, Span is set to____MHz while measuring RF Power from RF 67 1 2 200 4 C Amplifier 68 To measure the RF Power from RF Amplifier we used DMM Power meter Spectrum analyzer Adaptor C 69 Network analyzer is used to measure VSWR Cable Loss insertion loss ALL ARE CORRECT D 70 While measuring VSWR with network analyzer it should not exceed 1.3 2 1 3 A Which measuring tool is used to check the thickness of sheet metal and diameter of 71 Scriber Wire Gauge Calipers Fitter Square B wires ? 72 Before using network analyzer always call it with TMR Kit load call kit short C 73 Network Analyzer need not to be calibirated by PME Cell because it has Call kit TRUE FALSE F 74 To adjust a measuring instrument to a known standard value is known as……… Maintenence Calibration Justification Inspection B Which mearing tool is used to measure distances to the nearest one thousandth of an 75 Scriber Wire Gauge Calipers Micrometer D inch ? 76 Which mearing tool is used to setout distance and scribing the circle? Scriber Divider Calipers Fitter Square B The deterioration of a metal by its reaction to environmental elements or direct chemical 77 Ionization Corrosion chemical effect Heating Effect B attacks is known as … 78 The purpose of corrosion resistant coating is to interrupt the corrosion reaction. TRUE FALSE T Paints, varnishes, lacquers, enamels, oils and waxes are used to protect metal surfaces 79 Organic coatings Metallic coating oxide coatings All are correct A from atmospheric corrosion and known as ? These coating are known as conversion coatings because during the………….. the metal 80 Metallic coating Chemical treatment Organic coatings oxide coatings B at the surface is converted to a metallic compound. The occurance / accumulation of corrosiondue to the tendency of a metal to return to 81 TRUE FALSE T their natural state. 82 An increase in temperature will decrease the speed of corrosion. TRUE FALSE F 83 The electrolyte is the most important factor of corrosion. TRUE FALSE T Which is the simplest form of corrosion and may occur in atmosphere in liquid or in the 84 Uniform etch corrosion Pitting corrosion Galvanic corrosion Filliforn corrosion A soil ? Which type of corrosion occurs when two metal of different electrode potential contact 85 Uniform etch corrosion Pitting corrosion Galvanic corrosion Filliforn corrosion C each others ? 86 Which type of corrosion caused by diffusion of oxygen and water through coating ? Pitting corrosion Galvanic corrosion Filliforn corrosion Intergranular corrosion C 87 Which type of corrosion cause by combined effectof cyclic stress and corrosion ? Galvanic corrosion Filliforn corrosion Fatigue corrosion Intergranular corrosion C length of timing it remains in 88 In Corrosion control method, The corrosive effect is determined by…..? composition of contamination the type of metal contact with the metal All are correct D surface Syscronious Digital Asyncronious Digital 89 ADSL stand for? Subscriber Non is correct B Subscriberline Subcriber Line 90 Input of IPAM is? Fibre optic Copper Coaxial Non is correct B Internet protocao access 91 IPAM stands for? internet protocol access Non is correct A Multiplex 92 An IPAM can provide access to users? 2 4 16 18 C 93 O/P level of o/p data is (-6.1dbm to -12 dbm (-12 to 13 dbm 7 dbm (-6.1 to -14.8 dbm D 94 Capasity of RAM of DCG 256MB 512MB 128MB 1024MB B used to copy folder one location used to remote login to an used to list the directories 95 LS command are used for All are correct C to another other work station. or folder 96 The data inputs to the primary radar tracker include Plots from DCG FnMM Plots from Moxa A&B are correct D 97 ADSL provide connectivity over? 2wire 4 wire 6wire 8 wire A 98 ADSL Modem Adoper voltages are? 9vdc 12vdc 24 V DC Non is correct B 99 ADSL Modem reveive data from BRAS? TRUE FALSE T 100 DSLAM is the advanced of IPAM Switch Card Non is correct A 101 A DSLAM can provide intranet or internet to users? 10 16 18 32 D 102 OFC is directly connected on DSLAM? TRUE FALSE T 103 Inside the DSLAM, OFC is converted into copper? TRUE FALSE T 104 Where does IPAM use? where NGN is available where NGN is not availabe In switch rooms Both B&C is correct D 105 02 PCI slots are used in DCG TRUE FALSE T 106 Out put voltages of MUPS are? 405 VAC 405 VDC 380 VAC 380 VDC C 107 One E & M card deals with? 2 radar 1radar 4 radar 5 radar A 108 One modem is used for how many radars? 1 4 3 2 A A Client is the network computer that has access to the network but doesn't share any of 109 TRUE FALSE T its own resourceswith the network. 110 Inside RFD enclosure the board which converts AC input to DC output is P-1 board P-2 board Interface board Panel driver board A 111 Inside RFD enclosure the board which provides Video signal to interface board P-1 board P-2 board Interface board Panel driver board B 112 The total number ofPCI slots thatare used in DCG are? 2 SLOTS 4 SLOTS 5 SLOTS 3 SLOTS A 113 Dailing Mode of 2+ 10 Field exchange auto line is? DTMF Puls Push Continous B 114 Dailing Mode of 2+ 10 Field exchange Fieldline is? DTMF Puls Push Continous C 115 DC Voltage requirement for 2+10 Field Exchange is? 12VDC 24 V DC 12AC 24VAC A 116 Ring out voltage of Field line of 2+10 Exchange is? 80VAC 80VDC 60VAC 60VDC A 117 Earthing value of 2+10 Field exchange is? 05OHM 10OHM 20 OHM 4-8OHM D 118 The type of MIC used for hand set of 2+10 Field exchange is ? carbon dynamic wired piezo-electric A 119 Call relay circuit used in 2+10 lines exchange can handle----------lines. 5 6 4 10 B 120 MIC energizing volts for 2+10 lines handset mic are? 5 VDC 12 VDC 9 VDC 24 VDC A Which form is use for local manufacture of FM code assemblies to maintenance activities 121 Form – 48 Form – 244 Form – 1348 Form – 118 A from the requesting organization ? 122 TMA was previously known as Form……... Form – 48 Form - 35 Form - 6 Form – 118 B 123 TMA of Avcs (G) trade must be renewed on …………. Basis. 3 monthly 6 monthly 9 monthly 12 monthly D 124 At Squadron level, who is responsibie for ensuring timely renewal of TMA ? Trg Co-ordinator WO i/c TE & C Flt O i/c work center BTO A 125 Form 43 C is to be signed by O i/c on ___________ basis. Monthly Quarterly Fortnightly Daily D 126 "Maintenance inspection record" is to be recorded on PAF Form? Form 43 Form 43 A Form 43 B Form 43 C A 127 Durning maintenance, the 'Components record' is tobe annotated on PAF Form? Form 43 Form 43 A Form 43 B Form 43 C B Maintenance routine 128 Form 43 B is use for? Components record Modification record Maintenance inspection record C records 129 The PAF Form which shows the serviceability of the component ? Form 50 E Form 244 Form 50 D Form 50 B D 130 Which Form must be use and attached with repairable components ? Form 50 B Form 50 D Form 244 Form 50 E B PAF Form when attached with PAF equipment / items shows a rejected or condemned 131 Form 50 B Form 50 D Form 50 E Form 244 C item ? 132 AF Form 48 will be raised in how many copies ? Two Three Four Six C Which PAF Form required to fill block for reason of condemnation or authority who has 133 Form 244 Form 50 B Form 50 D Form 50 E D declared the item condemnation ? 134 What is the form number of 'Loan card' ? Form 244 Form 667 PAF Form 668 Form 118 C Equipment is not under immediate supervision of inventory holder charge, which form will 135 Form 667 Form-668 Form 37 PAF F-10999 B be raised to show an accurate state of holdings ? 136 Any loan card held for a period exceeding six months is to be rendered invalid.? TRUE FALSE T If the equipment is not under immediate supervision of the inventory holder, he is to 137 Form 667 Form 37 AFTO F-668 PAF F-10999 C exercise control by means of? In case where an inventory holder proceeds on leave or temporary duty, the inventory is 138 O i/c Flight Sqn Cdr OC Unit Base Cdr D to be handed over at the discretion of ? Inventory holder is responsible to pass duplicate copies of all issue / Turn in vouchers to 139 12 hrs 24 hrs 48 hrs 72 hrs B EAS within …….. after the transaction takes place at Log Sqn.? 140 Form 37 is use for? Kit Form Inventory Bench Stock Pre issue B 141 Form 37 sheet 1 is raised in how many copies ? 1 2 3 4 A 142 Form 37 sheet 2 is raised in how many copies ? 1 2 3 4 B Which copy of AF Form 48 will be forwarded to the user agency as notice that the work 143 First copy Copy 2 Both Copies Four Copy B requested has been started ? 144 What is the form number of System / Equipment status record form ? Form 50 B Form 50 D Form 50 E Form 244 D 145 How many sub parts of System/Equipment status record form ? 2 3 5 7 C Which form provides a means to document equipment delayed discrepancies, record 146 Form 50 D Form 244 Form 50 E Form 50 B B inspection status and historical data ? A separate AFTO Form 244 will not be maintained for items having specific inspection 147 TRUE FALSE F requirements. 148 Two copies of F-48 will be retained for Material Control File. TRUE FALSE T 149 Which PAF form is used for Turn In procedure of items? Form – 48 Form – 50 D Form – 350 DD Form – 1348 D 150 F-1348 raised in how many copies for demand procedure ? ONE TWO THREE FOUR B 151 When u/s item is turned in to log sqn, how many copies of F-1348 are used ? ONE TWO THREE FOUR B 152 Which form has replaced Form 2005 ? Form 6 DD Form – 1348 Form 48 Form 37 B On promotion to the rank of Senior Technician where individual would be required to act 153 Group -1 Group -2 Group -3 Group -4 D and sign as supervisor. The initial issue of TMA shall be done in which group ? 154 In a Sensor's unit maintenance acticities comes directly under NCO i/c SEO OC Wings Base Commander B Indoctrination of personnel is one of the most important preventive securitymeasures 155 TRUE FALSE T against hostile ingress.? Unfriendly and enemy countries' Radio / TV broadcasts relating to Pakistan may often be Foreign Propaganda 156 meant for projection of their own view points and / or for subversion of Pakistanis. It is Culture Motivation All are correct C Broadcasts called.? All personnel of PAF are to keep with religious gatherings / organizations, which may 157 TRUE FALSE F have any political / sectarian colour. Who is responsible for security education / indoctrination of personnel by arranging Officers Commanding 158 security lectures, displaying security posters and publication of security tips / slogans in AHQ Base Security Officer OC FLUs C bases / units BROs / UROs.? Use of service resources or institutions to propagate beliefs / views of any particular sect 159 TRUE FALSE T or organization is not allowed.? 160 Documents up to Secret classification may be held on the charge of an JCO? TRUE FALSE T 161 Top Secret and other accountable documents are to be held onthe charge of ? SNCOs JCOs Officers UDCs C The keys of containers of documents up to Top Secret classification are to be deposited 162 TRUE FALSE F with O i/c section at cease-work. A new ribbon used for typing classified letters / notes is to be removed from the 163 typewriter at cease-work and kept in safe custody, unless the ribbon has been rewound TRUE FALSE T in the process of typing?  The hostile intelligence agencies do not acquire the information they seek as a whole but 164 TRUE FALSE T try to collect in bits and pieces. 165 In a Sensor's unit SEO comes under ---------- OC Engg OC Wings Base Commander OC Unit D Interception of wireless and telephone communications by the enemy can provide all the 166 TRUE FALSE T useful information concerning our order of battle, locations and plans.? Writers of service articles must impose self-censorship to ensure that any information 167 TRUE FALSE F considered useful to the enemy is carefully included.? Notice boards displaying Routine Orders and other such information are to be so placed 168 TRUE FALSE F as to be readily accessible to unauthorized civilians or visitors.? Avoid indiscreet talk and always guard against inclusion of service matters in private 169 TRUE FALSE T correspondence or emails.? Harmful effects of excessive microwave radiation result from either a general rise in the 170 TRUE FALSE T total body temperature or from selective heating parts of the body. Fire hazards such as POL stores, ammunition stores and paint spray booths of stores Quarter mile for highpower 150 Feet for Low Quarter mile for Lowpower 171 100 Feet for high power radar B are not to be sited when high power Radar is giving operation.the distances is? Radar powerRadar Radar Fuel tanks are not to be filledwhen the radar set is in operation. The area specified in 150 Feet for Low Quarter mile for highpower Quarter mile for Lowpower 172 100 Feet for high power radar C AFO is? powerRadar Radar Radar To avoid any risk of fire or explosion,within a radius of 100 feet from a low powered 173 radar, Plastic containers are not to be used for filling purposes as static electricity can TRUE FALSE T cause ignition? Before any work is started on the antenna and associated equipment, It must be 174 ensured that electrical power to all pedestal circuits including the antenna rotating or TRUE FALSE F nodding mechanism is turned ON.? 175 A good House keepingminimize the occurances.It isthe primary responsibility of? Oi/c Every worker Unit Adjt UWO B 176 In a Sensor's unit maintenance corresponding carried out through ------- orderily room 2ic maint control adjutant C 177 Good house keeping and cleaning is not necessary to perform a job successfully.? TRUE FALSE F Keeping the tester, tool and other equipment in proper order is not good house 178 TRUE FALSE F keeping.? Oil spilled on the floor can cause fire or can obstruct the person working in the 179 TRUE FALSE T workshop. Who is responible to carrying out percentage check of first aid fire fighting appliances 180 O i/c Base Fire Flight OC Flying Wing OC Admin Wing Base Commander A held at the Base and ensuring their state of serviceability ? 181 The method in which thetemperature of the burning material is called ? Starvation Smothering Ignition Cooling D 182 Reducing the oxygen content within the fire area below the burnable limit is known ? Smothering Starvation Cooling Ignition A 183 By emoving the burnable material from vicinity is called ? Cooling Starvation Smothering Ignition B An increase in the total body temperature of 1° centigrade is considered excessive, and 184 TRUE FALSE T prolonged exposure or too high a temperature rise can be fatal.? For personeel safety, anareas of high power density should be locked or otherwise 185 TRUE FALSE T made inaccessible when transmitting.? Whenever personnel are working insuch areas where the power density is at a 186 TRUE FALSE T dangerous level, they should be protected with screened enclosures. 187 In a Sensor's unit shift supervisor is responsible----------- NCO i/c SEO OC Wings Base Commander A When the antenna is at ground level, the only safe way of avoiding radiation hazard is to 188 keep personnel from approaching the antenna any closer than a “Safe” distance, while TRUE FALSE F the radar transmitter is radiating? At workplaces where there are flammable liquids or flammable atmospheres 189 present.There is no risk that the static shock will ignite the liquid or atmosphere causing TRUE FALSE F fire or explosion.? 190 High voltage power lines can arc across distances of over 10 meters through air. TRUE FALSE T The buildup of potential difference (voltage) between surfaces as a result of friction 191 battery supply Static electricity Main supply None is correct B between them is called _________. Most overhead power lines are insulated because of this any work carried out near to 192 TRUE FALSE F these power lines has a risk of electrical arcing. Who is responsible to ensure and conduct of periodic maintenance routines of the 193 O i/c Flt OC Engg OC Flying SATCO B system. ? Who is first supervisor of maintenance production and as such, is technicalauthority and 194 Shift worker Section incharge O i/c work center Sqn Cdr B advisor in his specialty area ? 195 Who will serves as the senior technical advisor within his area of responsibility.? Shift worker Section incharge O i/c Flight Sqn Cdr C 196 A person responsible to ensure compliance with security and safety procedures ? NCO i/c Section WO i/c Section O i/c Flight Sqn Cdr C To detect and neutralize enemy psychological operations such as rumours,propaganda, 197 TRUE FALSE T misinformation that lower the morale of people is the objective of personnel security.? Temperature of rubber store is to be maintained from –5 to 25°C (for A/C tyres & 294 TRUE FALSE T tubes). 295 The whole exterior of the equipment must be? Clean Freefrom dust Free from Oil All are correct D 296 Oil is use as acleaning solvent for Guy Winches? TRUE FALSE T 297 To avoid rust and smoothmovement of Guy Wires, which solvent need to be use? Degryser Grease Contact Cleaner Glint B 298 Wooden chalks are used for the safety of the ----------- vihicles moving parked heavy light B 299 Wooden chalks are used as a safety material durind ----------. movement of radar attaching mobilizer with radar alignment of radar A & B are correct D 300 One of the following can be used to align mobilizer with the TG/Shelter Bar prey TMR Kit Davit Crane Wooden Chalk D 301 Wooden chalkis included in the tool kit of------- TG Shelter Mobilizer PDA C Responsibility for the periodic inspections and to ensure theserviceability/recharging of 302 Engg Wing Fire Flt Section BWO B the fire fighting appliances, held on the baseis? 303 Carbon Di-oxide CO2 gas extiguisher is use on all types of fire.? TRUE FALSE T Which type of fire extinguisher is use on all types of fires especially on liquid and electric 5 lbs Dry ChemicalPowder 25 lbs Dry Chemical Powder 304 Carbon-Di-Oxide (Co2) 1 Kg DCPFire Extinguisher A fires ? Extinguishers Extinguishers 305 Oil should not be splashed in rubber store. TRUE FALSE T 306 How many types of 25 lbs Dry Chemical Powder Extinguishers are use in PAF ? 2 types 3 types 4 types 5 types C 307 1KG DCP Fire Extinguisher is use to extinguish thetype of fire ? Solid Fire Electical Fire Liquid Fire All are correct C All high voltage points which are potentially dangerous to personnel, are enclosed behind 308 TRUE FALSE T doors or panels which are normally closed.? Keep all doors, panels and equipment drawers closed and locked except when 309 TRUE FALSE T servicing.? 310 Do not discharge all exposed terminals to earth before working on the RF assemblies.? TRUE FALSE F Before attempting to remove any waveguide component, ensure that the compressor 311 TRUE FALSE F supplying the air to the waveguide is switched ON. Prior to connecting or disconnecting any test equipment, all electrical power is to 312 TRUE FALSE T removed from the system. ? 313 As a classification of fire, Rubber Fire is classified as? Liquid Solid Electric All are correct A 314 As isolation………………is useto avoid electrict shock. Wooden plank Rubber mate Plastic sheet Woolen cloth B 315 Metal connectors can be cleaned with.? ContactCleaner Glint Grease None is correct A 316 Materials used for cleaning or grinding of any surface are called? abrasives synthetic materials oil & greases rubber products A 317 Which type of cleaner is use for Electronics PCBs.? Degryser Thinner Contact Cleaner Glint B 318 Metalcasings of different equipment should have to be cleaned by using? Degryser Thinner Contact Cleaner Glint D 319 The presence of oil or grease will make work on mechanical system? Very easy Not very easy Dangerous non is correct C 320 Types of earthing are? 02 types 03 types 04 types 05 types B 321 Lightening arrestor should be installed with ……… Equipment Building Generator A&B are correct D 322 Which instrument is used to check the resistance value of earthing ? Fluke 177 Oscilloscope DMM Megger D The region where the depth of under ground water is more, under ground method is 323 TRUE FALSE T practicable only. Accidentally if positive lead (line) touches the frame or body of the equipment, it is 324 TRUE FALSE T neutralised through the ground point. What will help in prevention of accident and save the valuable lives which otherwise are 325 Low Voltages Low current Safe installation Earthing D subjected to a serious shock ? ………..is a way of protecting equipment so that in the event of an electrical fault, 326 current flows safely to earth rather than flowing through a person who might be touching Maintenance Conductance Isolation Earthing D the equipment. 327 Water Pipe Earthing method is applicable where the load is less than……… 12 KW 15 KW 30 KW 50 KW A 328 Separation of earthing may not be made between electronic and electrical equipment. TRUE FALSE F 329 Mesh topology may be used for electronic earthing TRUE FALSE T 330 Earthing value resistance of Electrical equipment must be less than? 2.5 Ohm 05 Ohm 10 Ohm 20 Ohm B 331 Earthing value resistance of building must be less than? 2.5 Ohm 05 Ohm 10 Ohm 20 Ohm C A process of connecting one or more metallic objects and conductors to ground 332 Soldering Hardening Welding Earthing D electrodes is called? 333 Earthing resistance value of building should be checked on ? 3 Monthly 6 Monthly Annual Monthly A 334 While earthing the equipment, what must be considered and given the importance ? Voltages Load Current Ohmic value B The frame of electrical equipment connected by a flexible copper wire to a ground plate 335 Patching Connectivity Earthing Installation C which in turn is buried under the ground is known as………… 336 When the load is less than ……….. the earthing is to be carried out locally. 12 KW 15 KW 30 KW 50 KW A 337 Earthing value resistance of Electronics equipment must be less than……… 2.5 Ohm 05 Ohm 10 Ohm 20 Ohm A 387 Daily Inspection is c/out by? Shift worker NCO i/c WO i/c QA Team A 388 Monthly routines is c/out according to? SOPs Work Orders TO,s None is correct A 389 The Form which form is use to maintain monthly inspection record of a system ? F-43 series F-50E F-244 F-37 A 390 Monthly routines are c/out by ? Shift worker Technical staff WO/NCO i/c Section All are correct D 391 Annual maintenance routines are? Scheduled maintenance U/scheduled maintenance corrective maintenance None is correct A 392 All Annual routines of the system c/out according to? SOPs LOPs Work card None is correct C 393 Annual maintenance routines are to complete in given time by? SATCO DATCO AHQ OC ENGG A 394 Annual maitenance routines are best to improve the performance of? Personnel PME equipment Support equipment Complete system D 395 DI of PME Items is maintained on? F-50E F-50B F-244 F-37 C 396 DI of powered system is c/out according to? SOPs LOPs Work card None is correct A 397 Daily inspection record of a system is maintained on ? F-50E F-43 series F-244 F-37 B 398 Weekly inspection routines are? Correctivemaintenance Preventive maintenance U/scheduled maintenance All are correct B 399 Weekly Inspection is c/out by? Shift worker Shift Supervisor WO i/c A&B D 400 Weekly inspection of ACs is C/out by? User activity AC shop QA Sqn All are correct A 401 Which equipment require weekly inspection routines.? Powered Non powered only system A&B D 402 Monthly inspection routines are known as? Correctivemaintenance Preventive maintenance U/scheduled maintenance All are correct B Barriers to good standards of health and safety in a workplace is that to complete the 491 TRUE FALSE T assigned task in hurry so as to produce the desired results compromising the safety. 492 When a system is connected to an electrical power source it is described as "Dead". TRUE FALSE F Any environmental factors that increase resistance will cause an increase in current flow 493 TRUE FALSE F and therefore increase the severity of the shock. 494 The principle of treatment is 'avoid infection". TRUE FALSE T Watch the patient for some time to see that breathing does not fail, if it does, begin Electro Static Discharge 495 Light Hazards Electric shock Explosion B artificial respiration again, in case of…….? Hazard 496 Imitate the movement of breathing to induce inspiration in case of ? Burning Drowning Electric shock Explosion C 497 Keep the patient warm by covering with blanket or extra covering in case of ? Drowning Explosion Burning Electric shock D 498 Radiation from radar transmitters can produce physiological damage to personnel. TRUE FALSE T Electro-explosive devices when exposed to radiations from a radar antennaconstitute fire 499 TRUE FALSE T hazard. “Safe” distance, while the radar transmitter is radiating, The minimum distance which is 500 TRUE FALSE T considered “safe” is that at which the average power density is below 10 mw/cm2.  As a safety precaution, areas of high power density should be fenced off, locked, or 501 TRUE FALSE T otherwise made inaccessible when transmitting. The solution to a health and safety problem usually requires a worker to carry out their 502 TRUE FALSE T job in a particular way. Personnel should look into an open waveguide or antenna feed horn connected to 503 TRUE FALSE F energized transmitters. Whenever work is carried out on the exterior, walkways are provided, together with foot 504 TRUE FALSE T and hand rails, these are not intended to be a substitute for the use of safety belts. After the equipment is switched ON, the maintenance personnel must satisfy themselves 505 TRUE FALSE F that nobody else is working out of their sight. Some of the fluids and oils used with the equipment might cause skin irritation or 506 dermatitis to personnel who may be allergic to them. To prevent this, Safety Belt should TRUE FALSE F always be worn when handling thefluids. With compromising the operational effectiveness of a particular site, position the 507 equipment trailers/cabin in such a way that these stand directly in line with wind direction TRUE FALSE F generally prevailing in that area. Health and safety standards are affected by worker behaviour can not be a significant 508 TRUE FALSE F barrier to maintaining good standards in a workplace. Tools and equipment used by worker at work, The greater the risk involved, the greater 509 TRUE FALSE T the care that must be taken. use of poorly maintained contact with underground use of electrical equipment 510 High risk of electric shock work activities include ………………. All are correct D electrical equipment powercables in wet environments 511 High voltage power lines can arc across distances of over………...through air. 10 metres 15 metres 20 metres 25 metres A When a person receives an electric shock they can suffer a range of effects, from mild 512 TRUE FALSE T discomfort and muscle tremor. 513 The hazards of electricity are ………… Burns Fire and explosion Arcing. All are correct D Electric shock occurs when electrical current passes through the body, using the body as 514 TRUE FALSE F a insolator. 564 Before Lowering the TG positon the Service Lift to Lowering position Remove Lower position Upper position A 565 Sun strobe alignment is necessory after -------- Re location of TG Raising of TG Maint None A 566 Data analysis of sun strobe is c/out in ------- CPERF ODAS MFI SAS B 567 Before the Sun strobe alignment the -------- alignment is necessary System Receivers Course Fine C 568 Before dis-assembling of Mobilizer position the Mobilize on Flate surface Ramp Jacks None A 569 Before dis-assembling of Mobilizer perform ---------- pre inspection post inspection Quarterly inspection Monthly inspection A 570 Remove all power cables & pressure cables before dis-assembling of Mobilizers TRUE FALSE T 571 While moving individual front or rear dolly of mobilizer do not stand in front of ----- Wheel truck Shelter TG Supervisor A 572 To move a portion of mobilizer we can use------ Prime Mover Fork Lifter Jacks None B 573 Power requirement for hydraulic system of mobilizer 24 V DC 115V 12V 380V A 574 Do not remove power cables &hydrauliccables before disassembling of Mobilizers TRUE FALSE F 575 Antenna Jack No.4 must be -----------before lowering the TG Extended to ground Raise Removed None A 576 While moving of portion of mobilizer donot stand in front of ----- Wheel truck Shelter TG Supervisor A 577 How many person are required for antenna lowering 1 2 3 4 C Measure the Actuater extension if it is greater than --------- stop the lowering and adjust 578 0.75 inch 1 Ft 0.5 M 2 Ft A the error 579 Course leveling are c/out with the help of Level Electronic Bubble on TG Leveling jacks Sand pads B 580 Fine leveling of TG is carried out with Level Electronic Bubble on TG Leveling jacks Sand pads A 581 Antenna leveling must be carried out after leveling jacks up/down deployment of TG Lowering of TG to ground All are correct D 582 Tools required for leveling of TG TG tool kit Level Electronics A&B None C 583 The data recording of sun strobe is c/out --------minute after the sun is on 05 to15 digree 30 Min 50 Min 1 Hr 1.30 Hr A 584 Separate parking arrangements must be made for different kinds of vehicles TRUE FALSE T 585 Reserved parking sheds must be identified for Commanding Officers TRUE FALSE T 586 No need to lock vehicles in parking area. TRUE FALSE F 587 Parking area must not be covered with shed. TRUE FALSE F 588 Parking arrangments will vary to utilize local space facilities to the maximum. TRUE FALSE T 589 Proper jacking up of vehicles is essentisl to secure---------of the vehicles. Fule paint tyre speed C 590 Proper jacking up of vehicles is essentisl also for one of the following reason. speed limit tuning alignment proper leveling B All data storage / access devices (Lifed and consumable) are to be registered by the 591 TRUE FALSE T recipient Dte / Unit at the time of their receipt, by allotting a Registration Number. Who is responsible to ensure that all data copied from / to portable storage media is 592 O IC Electronics Unit ISO OC Egg Base IT Centre B encrypted with PAF Crypt ? 593 What should be kept in mind while parking operational vihicle in the field area Distance b/w vihicles length of the cables maintenance activity All are correct D  To position the equipment trailers/cabin, efforts should be made to select such sites in 594 TRUE FALSE F the area which does not provide reasonable hard grounds for firmly inserting anchor pins. To position the equipment trailers/cabin, When selection of an operational site over a soft 595 TRUE FALSE T ground is unavoidable, the anchor pins must be deeply pegged into the ground. To position the equipment trailers/cabin, When deployed on hilly grounds or concrete 596 platforms the anchor pins must invariably be pegged deep into ground for stay wires Rope anchor pins None is correct A connecting………. Radar equipment should be completely switched off and safety procedures be enforced 597 whenever wind velocity exceed the maximum operating limit recommended by the TRUE FALSE T manufacturers. 598 Data storage / access devices are divided into how many categories ? Two Three Four Five A XB3 includes CDs, DVDs disks, Floppy disks, printer cartridges or any other similar 599 TRUE FALSE T media are Categories as consumables data storage / access devices. Hard Disks or CDs / DVDs Drives, USB Flash disks, Laptops, Wi-Fi / Bluetooth devices, 600 Memory Sticks, Digital Cameras, Switches, Routers or any other hardware capable of TRUE FALSE T storing information are Lifed items. 601 The device which provide communication between twodifferent network scheme is? Ethernet switch HUB Modem Router D 602 Maximum power rating of moxa server is 100 Watt 200 Watt 300 Watt 400 Watt B 603 In put of control power supply is 120VAC and 220 VAC 120 VAC 220 VAC 380 VAC A 604 I/P voltage of inverter portion is 405 VDC Approx TRUE FALSE T 605 The IP address of ROUTER is? 192.168.X.154 192.168.X.254 192.168X.155 192.168.X.255 B 606 GMCC communicate with SMCC through router ? TRUE FALSE T 607 Router 4305 supports up to ? 8 Ports 10 Ports 12 Ports 16 Ports A 608 Number of O/P channel for SOC data One Two Three Four B A valid MPDR data will flicker receive light atleast once specifying the presence of 609 2 Sec 4 Sec 6 Sec 8 Sec A reference pulse 610 Operting system of VRS is Solaris TRUE FALSE F 611 I/P of Modem bank is 220 VAC 48 VDC 30 VDC 380 VAC A 612 Input power for Moxa server is 48 VAC 48 VDC 220 VAC 220 VDC C 613 Tower earth value should be less than ______ 10ohm 5ohm 3ohm 1ohm A Antenna AK-214 / MC-214 is properly connected and Volume control is properly 614 Before switching the radio set M3SR into operation check that the ? KDD is properly load the rf connector is properly Check that FMX is on C adjusted connected at the back of Radio X30 connector. Proper earthing is conncected at Antenna cable is connected X31 / X32 connector is 615 Before connecting the main power supply cable to the radio set ensure that? All are correct D the back of M3SR radio set to the radio connected The rectifier power limit or The rectifier identifiy the 616 If all the LEDs of rectifier of FMX are flashing it means that The rectifier is u/s Due to DC over voltage B current limit is active function Try to check the proper If the Key LED on the front pannel of M3SR Radioset is not glowing and KDD is Data set would be feed or load Data set would not be load in 617 connection of KDD cable at Both B&C is correct D connected to the set then? in M3SR M3SR fill Gun connector of radio 618 Safety posters are displayed at Notice board Table Prominent places A & C are correct D 619 Accident always occurs due to Ignorance Over confidence Carelessness B & C are correct D This tag indicated a safety hazard with a medium potential risk for a user that can result 620 Danger Warning Caution Note D in death or serious injury Check that the Key LED on the Check that the load mode is Transmission and reception 621 If the KDD is connected to the M3SR and data or pre set are not loading? front pannel of M3SR must be display at the control unit of would not be possible if All are correct D on M3SR KDD is properly connected With foot adjustment brace. During installation of Clark mast sellect the smoth ground if available. If not then connect Otherwise the anttenna may 622 Screw driver with hands with iron road / packet D the tripot on the unbalance ground and adjust the legs by not be balance and it may fall down During operation if the transmission from the GB is not conducted, immediately check the 623 TRUE FALSE T X1 connector at the rear of GB 208. 624 Earthing should be tested with _______. Ohm meter Power mter Earth tester DMM B Loud speaker of GB may be Check the jumber X29 is 625 f the PTT Keyremain dark during operation it well be due to? Check the function of PTT key Non is correct A defective not properly pluged in Do not creat a panic, check its No receive channel may be No modulation of AF signal 626 If there is no reception on GB 208 during an operation? volume control. It may be turned sellected by the controller / or PTT key may not be Both a & b is correct D fully clockwise operator pressed properly.  It should be sent to the repair During verifying the serviceability of a faulty GB-208. After replacing the fuses and then it It may be further checked at facility. Don’t try to repair it 627 It may be stored Non is correct B does not switch on then local bench otherwise authorize by a higher authority. If the other connector is not Its mating connector is also checked then it may cause to No need to check the other 628 If any cable Of GB-208 shows discolouration cause by heat it mean that ? Both a & b is correct D defective. Check them all spark and the whole GB connectors would beacem u/s. Remove th battery cable Remove th battery cable 629 Before changing or replacement the fuses of GB-208 Switch Off the main AC supply All are correct D from the connector X200 from the connector X100 Do not remove any item from the mast guide box. Slightly The insertion of cross pin in the raise the antenna and insert Only remove the lefting block 630 After errection of clark Mast ? last mast section is not Remove the hoist only the cross pin in the last mast D from the mast guide box necessary section other wise the mast well fall down and hurt person or equipment. Lower the mast sufficent to Only relase the winch 631 If by mistake the mast is raised and the winch ooperator forget to let out the Guys then? relase guy tension before Donot lower the mast Go ahead A ratchet relasing winch ratchet Always keep a hand on Guy 632 To avoid any un wanted situation during errection / lowering of clark mast in strong wind Always keep a hand on packet Always keep a hand on hoist winchhandel when Guys are Non is correct C