Mastering AP Azimuth Marking for Enhanced Sales Targeting

Play an AI-generated podcast conversation about this lesson

What color does the RF LED indicator turn when the radio is in alignment mode?

Red
Blue
Green
Orange (correct)

What should technicians do after adjusting the azimuth or elevation?

Adjust the remote and local radio at the same time
Disconnect the voltmeter
Tighten all adjustment bolts (correct)
Restart the alignment process

What is the expected target RSSI level?

Within ±6 dB
Within ±2 dB
Within ±4 dB (correct)
Within ±8 dB

How long should technicians push the utility button to reboot the radio?

10 seconds (D) Signup and view all the answers

Where should the radio be placed during the 2ft antenna installation?

Pointing up (C) Signup and view all the answers

What is the maximum size of pole that the mounting bracket is suitable for?

2-4 inches (C) Signup and view all the answers

How many support arms should be used to secure the Welink mount?

At least two support arms (C) Signup and view all the answers

What is the purpose of the Siklu and Aviat radio provisioning?

Refer to the Seed E-band Radio Installation & Provisioning Guide (B) Signup and view all the answers

What is the elevation difference that the bracket supports?

-10 to +60 degrees (C) Signup and view all the answers

What happens when the mounting bracket is rotated upside down?

Gains -60 degrees in elevation (A) Signup and view all the answers

What should technicians ensure about the weep hole on the bottom of the antenna?

It should be open to allow water to fill the dish (C) Signup and view all the answers

What should be done to the plastic cap on the radome before alignment?

It should be kept on the radome (C) Signup and view all the answers

What should be used to assist with pointing the radio at the remote site?

A plastic alignment tube (B) Signup and view all the answers

What type of cables should be used for all ethernet cables connected to the radio?

Outdoor and UV rated (D) Signup and view all the answers

What should be used to secure the DC connector in Port 5?

A hand to tighten (A) Signup and view all the answers

What is the purpose of loosening the mounting plate bolts after alignment?

To use adjustment bolts for azimuth and vertical for final alignment (D) Signup and view all the answers

What should be done to fine tune each site during alignment?

Use adjustment bolts for azimuth and vertical for final alignment (B) Signup and view all the answers

What is the orientation of the Cube for horizontal polarized antenna propagation?

Horizontal (A) Signup and view all the answers

What should be done to ensure that the U-bolt has not slipped into one of the holes in the J-arm?

Use appropriate spacing for CUB mounts (B) Signup and view all the answers

What is the purpose of the weep hole when installing in horizontal orientation?

To drain water from the Cube (B) Signup and view all the answers

What color should Port 2 be marked with according to the cable management guidelines?

Red (A) Signup and view all the answers

What is the recommended distance between the MBU and the bottom edge/roof during installation?

25cm (A) Signup and view all the answers

What type of patch cables are recommended for outdoor use according to the cable management guidelines?

Cat5E patch cables with outdoor shielding (C) Signup and view all the answers

What should be done to the MBU during provisioning process?

Reset to default once (B) Signup and view all the answers

How should the MBU be attached to the pole during installation?

Using a hose clamp (D) Signup and view all the answers

What type of cable should be used for outdoor radio installations?

Cat5E or higher (B) Signup and view all the answers

What should you do if the AP you were supposed to shoot to is not present?

Contact FOS (D) Signup and view all the answers

What is the IP address to log into the CUB?

192.168.201.1 (B) Signup and view all the answers

What should you use to cover the low voltage mount bracket?

1-hole wall plate (D) Signup and view all the answers

What should you do if you can't achieve the target RSSI?

Try to achieve -60 dbm or higher (B) Signup and view all the answers

What is the recommended diameter range for the pole that the antenna should be mounted on?

2 to 4.5 inches (A) Signup and view all the answers

What should be done after making a rough azimuth alignment using a LOS visual check with the remote end?

Follow Radio Link Alignment procedure (D) Signup and view all the answers

What should be done before assembling the antenna?

Apply the brown grease provided in the box to all threads of the nuts and bolts (A) Signup and view all the answers

What should be done after mounting the plate to the back of the antenna?

Ensure correct polarization whether V or H according to build sheet (C) Signup and view all the answers

What should be done to the weep hole plug after installing the antenna?

It should be removed from the bottom and plugged in the top (A) Signup and view all the answers

What is the purpose of recording the location and azimuth of an AP in TechView?

To help the planning team predict serviceable homes for that AP (A) Signup and view all the answers

What should be done if an AP is adjusted or moved?

Record the new location and azimuth in TechView (A) Signup and view all the answers

What should be done to ensure proper installation of the Cube Radio?

Place a torpedo on top of the radio to ensure its level (B) Signup and view all the answers

What should be done with the U-bolt during installation?

Ensure that the U-bolt has not slipped into one of the holes in the J-arm (A) Signup and view all the answers

What should be done after entering the WAN MAC address from the Leaf radio label into TechView?

Save the information (D) Signup and view all the answers

What is the protocol for building a site that is over 200 meters from the connecting site, according to the text?

A technician can build it alone but must consult with their manager and work with scheduling to arrange another technician's assistance. (C) Signup and view all the answers

What is the purpose of using the CUB Radio Alignment tool, according to the text?

To establish a link between the technician's device and the remote radio. (D) Signup and view all the answers

Where should a technician place an AP during installation, according to the text?

To the side using the standoff mount or preferably above the radio cubes. (D) Signup and view all the answers

What is the recommended way to achieve LOS for the AP during installation, if necessary, according to the text?

Use the pipe extension. (B) Signup and view all the answers

What is the purpose of the Techview tool, according to the text?

To find the link's target RSSI. (D) Signup and view all the answers