Lock Service Cable Connection and Parameter Readout Instructions

Podcast Beta

Play an AI-generated podcast conversation about this lesson

Questions and Answers

How can a connection be added in the service PC setup process?

Click the Add button and enter server data.

What steps are involved in deleting a connection in the service PC setup process?

Select the connection and click the Delete button.

How can a connection be edited in the service PC setup process?

Select the connection and click the Edit button.

What is required to authenticate the service PC with the server in order to connect?

Registration code Signup and view all the answers

How is the system ID obtained from the PC software?

Click the Get button. Signup and view all the answers

When can the power open token and the coldstart token be accessed for download?

When system ID has been set. Signup and view all the answers

How is the communication between service PC and USB interface 3G handled?

By the FTDI driver Signup and view all the answers

What is the name given to the first connected USB interface 3G?

FTDI0 Signup and view all the answers

How can the FTDI driver be obtained if not detected by the operating system?

Download from the FTDI website Signup and view all the answers

How many events can be saved to the database in the LockLog section?

3000 Signup and view all the answers

What are the four selections available in the Readout section?

LockLog, Parameters, Passage schedule, Status Signup and view all the answers

What are the four different tabs found under the Parameters section?

General, Lock, Module, Misc Signup and view all the answers

What happens if the time difference between the lock and the service PC is more than 5 minutes?

A question to set the time will be shown. Signup and view all the answers

How is 'battery is low' indicated in the lock?

By four orange LED blinks and one green LED blink. Signup and view all the answers

How is 'battery is critical' indicated in the lock?

By four orange LED blinks and one red LED blink. Signup and view all the answers

What criteria need to be met for BLE module parameters to be shown?

Built-in BLE module in specific LCU models or using a separate BLE module of generation 2, along with LCU firmware version 3.xx.38.xx or higher. Signup and view all the answers

When is the idle battery voltage measured?

Once per hour. Signup and view all the answers

What action is triggered if a valid card is presented and the battery voltage (load) is low or critical?

'Battery is low' is signaled by LED blinks. Signup and view all the answers

Study Notes

Service PC Setup Process

A connection can be added in the service PC setup process.
To delete a connection, follow the deletion steps in the service PC setup process.
A connection can be edited in the service PC setup process.

Authentication and Connection

To authenticate the service PC with the server, specific requirements must be met to establish a connection.
The system ID is obtained from the PC software.

Tokens and Downloads

The power open token and the coldstart token can be accessed for download at a specific time.
The system ID is required to access these tokens.

Communication and USB Interface

The communication between the service PC and USB interface 3G is handled in a specific way.
The first connected USB interface 3G is given a specific name.

FTDI Driver

If the FTDI driver is not detected by the operating system, it can be obtained through alternative means.

LockLog and Event Limitations

Up to a certain number of events can be saved to the database in the LockLog section.

Readout and Parameters Sections

The Readout section provides four specific selections.
The Parameters section consists of four different tabs.

Time Difference and Lock Synchronization

If the time difference between the lock and the service PC exceeds 5 minutes, a specific outcome occurs.

Battery Status Indicators

A low battery is indicated in the lock through a specific method.
A critical battery is indicated in the lock through a different method.

BLE Module Parameters

BLE module parameters are shown if specific criteria are met.

Idle Battery Voltage Measurement

The idle battery voltage is measured at a specific time.

Card Presentation and Battery Voltage

If a valid card is presented and the battery voltage (load) is low or critical, a specific action is triggered.

Studying That Suits You

Use AI to generate personalized quizzes and flashcards to suit your learning preferences.

Description

This quiz provides instructions on how to connect the service cable to the lock and perform various operations such as checking time variances and reading lock-specific parameters. Learn about setting the time, comparing lock and PC times, and reading specific lock information.