SCADA Historical Configuration PDF

Recording configuration Page 1 of 4 Help > Historical records Introduction to the role of historical records Teach you how to configure and use historical records In the operation of the project, the val...

Recording configuration Page 1 of 4 Help > Historical records Introduction to the role of historical records Teach you how to configure and use historical records In the operation of the project, the value of the variable will change, and the process of recording these changes is called a historical record. The history record directly reflects the situation of engineering operation. The research and analysis of the data of historical records will be helpful to improve the project, so as to improve the production efficiency and quality. The history of the configuration software is divided into the timing records;trigger record and changing records. The time record is a numerical value that records the engineering variables at a specified time interval.Trigger record is to bind trigger variable and select trigger mode. Once triggered, it can record the value of engineering variable. Change records are recorded when the value of the variable is recorded. Recording configuration Figure-- History configuration window mk:@MSITStore:C:\PROGRA~2\Haiwell\HAIWEL~2\help(en).chm::/catalogue/historical... 9/17/2024 Recording configuration Page 2 of 4 Database type There are one types of database types:file database. Data storage location There are three methods for data storage location: "internal storage", "SD card", and "U disk". Set the data storage method as required. For the setting of the storage file size, when the stored data file is greater than the set value, a new storage file will be automatically created. After configuring the database type, data storage location, and data file size of the storage file, click "OK" to complete the configuration of the historical record. Record variables Record variables is a variable that needs to be saved in a configuration project, usually called a history variable. The configuration procedure is as follows: Step one: double click "historical records" node, the historical recording window will be popped up, as shown in the following figure: FIgure-- Historical recording window Step two: Click "add record variable" button, variable selector window will be popped up, then click "confirm selection" on the small box before the variable you want to add, to complete the adding of historical variables. As shown in the following figure: mk:@MSITStore:C:\PROGRA~2\Haiwell\HAIWEL~2\help(en).chm::/catalogue/historical... 9/17/2024 Recording configuration Page 3 of 4 FIgure-- Add historical variables Step three: Click the selected history variable to configure the select button, historical variable record setting window will be popped up. There are three ways of historical variables recording: timing records;trigger record and changing records. Timing records, select or enter the time interval to record in the interval, for example, the interval of one second, that is recorded once a second. Trigger type record, bind variables in the trigger variable box, and then select the trigger mode, such as binding switch Y0, and the trigger mode is off → on. Once the state of Y0 changes from off to on, the value of Engineering variables can be recorded.Changing records, set the value in the dead zone, for example, the dead zone is 0.5, which the current numerical value is more than 0.5 times the last one.(the first time is 32.2, the second time is 30, the record; the third time is 30.2, does not record; the fourth time is 31, recorded). As shown in the following figure: mk:@MSITStore:C:\PROGRA~2\Haiwell\HAIWEL~2\help(en).chm::/catalogue/historical... 9/17/2024 Recording configuration Page 4 of 4 FIgure-- Record variables setting Step five: Select the appropriate recording mode, and configure the corresponding record parameters, click "Yes" to complete the set of historical variables. Step six: In the historical variable description box, input the corresponding text on the historical variables are briefly described, explained. Read display The data of the historical variable can be shown through the historical curve and the historical report. There is no need to describe the historical curve and the historical report, if you want to know more, you can see "trend curve--- historical curve " section and" report---- create report "section. mk:@MSITStore:C:\PROGRA~2\Haiwell\HAIWEL~2\help(en).chm::/catalogue/historical... 9/17/2024 Alarm diagnostic data Page 1 of 8 Help > Alarm configuration and management > Set alarm Alarm groups：For easy to view、record and distinguish, the generated alarm information by the alarm variable will be divided into different groups, these groups are the alarm groups. Alarm levels：Ued to react to the contents of the alarm or the severity of the possible consequences of the event. Alarm configuration Figure-- set alarm Alarm groups Click the "Add" button, pop up the named window of alarm groups, input the name of alarm groups in the alarm groups box of the window, click the “OK” to complete the alarm groups to add. Click the "Delete" button, the selected alarm groups in the alarm groups box will be deleted. Such as the alarm groups of a total of the “alarm 1”, “alarm 2”, “alarm 3”, “alarm 4”, and click the selected “alarm 4” and click the "Delete", then the alarm groups will only have “alarm 1”, “alarm 2”, “alarm 3”. Click the "Move up" button, the current position of the alarm group will move up one. Such as the order of the alarm groups are “alarm 1”, “alarm 2”, “alarm 3”, click the selected “alarm 3” and click the "Move up", the order of the alarm groups are “alarm 1”, “alarm 3”, “alarm 2”. Click the "Move down" button, the current position of the alarm group will move down one. Such as the order of the alarm groups are “alarm 1” “alarm 3” “alarm 2” click the selected “alarm 3” and click the "Move down", the order of the file:///C:/Users/LENOVO/AppData/Local/Temp/~hh3F52.htm 9/17/2024 Alarm diagnostic data Page 2 of 8 alarm groups are alarm 1 , alarm 3 , alarm 2 , click the selected alarm 3 and click the "Move down", the order of the alarm groups are “alarm 1”, “alarm 2”, “alarm 3”. Alarm levels Click the "Add" button, pop up the named window of alarm levels, input the name of alarm levels in the alarm levels box of the window, click the “OK” to complete the alarm levels to add. Click the "Delete" button, the selected alarm levels in the alarm levels box will be deleted. Such as the alarm levels of a total of the “Top urgent”, “Urgent”, “General urgent”, “Not urgent”, and click the selected “Not urgent” and click the "Delete", then the alarm levels will only have “Topt urgent”, “Urgent”, “General urgent”. Click the "Move up" button, the current position of the alarm level will move up one. Such as the order of the alarm levels are “Top urgent”, “Urgent”, “General urgent”, click the selected “General urgent” and click the "Move up", the order of the alarm levels are “Top urgent”, “General urgent”, “Urgent”. Click the "Move down" button, the current position of the alarm level to move down one. Such as the order of the alarm levels are “Top urgent”, “General urgent”, “Urgent”, click the selected “General urgent” and click the "Move down", the order of the alarm levels are “Top urgent”, “Urgent”, “General urgent”. Alarm record When the alarm record is not enabled, there is no record of the alarm information when the project is running, Once you exit the project running, you can no longer query the information which is generated in the current running. It is not always recorded the generated alarm information of the project when ticking in the small box before the enabled alarm record, the alarm variables should simultaneously satisfy the alarm groups、alarm levels on the recording range of alarm information, then record the corresponding types of the alarm information according to the selected type of recording alarm information. The alarm groups have two kinds of choices: all the alarm groups and the specified alarm groups. If choose the all alarm groups, then the alarm groups of the alarm variables to be recorded in this range (at this time, the alarm groups of alarm variable can be empty); If choose the specified alarm groups , tick in the small box before alarm groups, then you can choose one or more alarm groups, also can not choose any one of the alarm groups. Only the alarm groups of the alarm variables in the range of the selected alarm groups, it is possible to record the alarm information of the alarm variables. The alarm levels have two kinds of choices：all the alarm levels and the specified alarm levels. If choose the all alarm levels then the alarm levels in which variables to be recorded of this range (at this time, the alarm levels of alarm variable can be empty); If choose the specified alarm groups , tick in the small box before the alarm groups, then you can file:///C:/Users/LENOVO/AppData/Local/Temp/~hh3F52.htm 9/17/2024 Alarm diagnostic data Page 3 of 8 choose one or more alarm levels, also can not choose any one of the alarm levels. Only the alarm levels of the alarm variables in the range of the selected alarm levels, it is possible to record the alarm information of the alarm variables Choose the alarm types to be recorded, there are two types of alarm and recovery. And tick in the small box before the alarm type to be recorded, which may record the alarm information of the type. Choose the time limit of saved date of the alarm information to be recorded, and alarm information which beyond the time limit of saved date will be automatically deleted. Configure the alarm configuration, click the “OK” to complete the alarm configuration. Sound alarm Figure audible alarm settings The first step: tick the small box in front of "Enable audible alarm", and the alarm information generated by the project operation will be prompted by audible alarm. Step 2: Click "New" to pop up the window for selecting alarm variables. After selecting the corresponding variable, click "OK". As shown below: file:///C:/Users/LENOVO/AppData/Local/Temp/~hh3F52.htm 9/17/2024 Alarm diagnostic data Page 4 of 8 Figure Select Alarm Variable Step 3: In the alarm occurrence sound and alarm recovery sound, click the select sound button, the alarm sound configuration window will pop up, select the corresponding alarm sound, you can click "trial" to understand its alarm sound effect, click the "confirm" button, Complete the sound configuration. as the picture shows: Figure Alarm sound configuration Alarm sound configuration There are four sound configuration modes: silent, system sound, sound file, and playback language. When the silent sound configuration is selected, no sound prompt will be generated when an alarm occurs in the running project. When selecting the system sound, you can select the sound in the system sound drop-down list. Select the sound file, click the select button to pop up the file opening window, and find the desired sound file. Select to play voice, click the select button to pop up the voice content input box, and input the voice file:///C:/Users/LENOVO/AppData/Local/Temp/~hh3F52.htm 9/17/2024 Alarm diagnostic data Page 5 of 8 content to be alarmed. MQTT reporting configuration The first step: tick the small box in front of "Remote Reporting MQTT". Step 2: Check "Alarm" and "Restore", set the name of "Group ID", select the reported service quality, and click "OK". The MQTT report configuration can be completed. Figure MQTT reporting configuration Alam diagnostic data Step 1: Tick the small box before "enable alarm diagnostic data". Step 2: Click "bind variable", select the required alarm diagnostic variable, and click "OK". The configuration of alarm diagnosis data can be completed. Figure Alam diaggnostic data Cloud alarm Tick the small box in front of "Enable Cloud Alarm" and click "Edit" to insert the content of the cloud alarm to be file:///C:/Users/LENOVO/AppData/Local/Temp/~hh3F52.htm 9/17/2024 Alarm diagnostic data Page 6 of 8 prompted. The alarm information generated by the project operation will be prompted by the cloud alarm. For cloud alarm configuration, the cloud alarm can be configured in various forms such as alarm group, alarm level, alarm type and alarm variable. The priority of the alarms in these ways is to perform audible alarms in sequence by variable alarm>alarm level alarm>alarm group alarm>alarm type alarm. Set the cloud alarm by alarm group: Step 1: On the alarm configuration page, add an alarm group. Step 2: On the cloud alarm, click to enable the cloud alarm and edit the alarm content. Click Press Alarm Group, and tick the name of the alarm group to be enabled. Figure Cloud alarm by alarm group Set the cloud alarm according to the alarm level: Step 1: On the alarm configuration page, add/decrease the alarm level. Step 2: On the cloud alarm, click to enable the cloud alarm and edit the alarm content. Click by alarm level and check the alarm level to be enabled. Figure Alarm level cloud alarm file:///C:/Users/LENOVO/AppData/Local/Temp/~hh3F52.htm 9/17/2024 Alarm diagnostic data Page 7 of 8 Set the cloud alarm by alarm type: Step 1: On the cloud alarm, click to enable the cloud alarm and edit the alarm content. Click by alarm type and check the alarm type to be enabled. Figure Alarm Type Cloud Alarm Set the cloud alarm by variable: Step 1: Click "New" to pop up the window for selecting alarm variables. After selecting the corresponding variable, click "OK". As shown below: Figure Select Alarm Variable Click "Delete" to delete the current alarm variable. file:///C:/Users/LENOVO/AppData/Local/Temp/~hh3F52.htm 9/17/2024 Alarm diagnostic data Page 8 of 8 Step 2: Check the "Alarm occurrence" or "Resume alarm" of the response variable, and click "Confirm" to complete the cloud alarm variable configuration. Figure Add Cloud Alarm Variable file:///C:/Users/LENOVO/AppData/Local/Temp/~hh3F52.htm 9/17/2024