Electronics Supplementary PDF

e-Notes by Prof.K.R.Sudhindra, BMS College of Engineering, Bangalore BASIC ELECTRONICS Subject Code: ELN-15/25 IA marks: 25 Hours per week : 04 Exam Hours 03 Total Hrs:...

e-Notes by Prof.K.R.Sudhindra, BMS College of Engineering, Bangalore BASIC ELECTRONICS Subject Code: ELN-15/25 IA marks: 25 Hours per week : 04 Exam Hours 03 Total Hrs: 52 Exam Marks: 100 CHAPTER 1 CONDUCTION IN SEMICONDUCTORS Electrons and holes in an intrinsic semiconductors, conductivity of a semiconductor, carrier concentrations in an intrinsic semiconductor, donor and acceptor impurities, charge densities in a semiconductor, Fermi level in a semiconductor having impurities, diffusion, carrier life time, Hall effect. 05 Hrs. The branch of engineering which deals with the flow of Electrons through vacuum, gas or semiconductor is called Electronics. Electronics essentially deals with electronic devices and their utilization. Atomic Structure Atom is the basic building block of all the elements. It consists of the central nucleus of positive charge around which small negatively charged particles called electrons revolve in different paths or orbits. An Electrostatic force of attraction between electrons and the nucleus holds up electrons in different orbits. Electrostatic force. + Centrifugal force. Figure1.1. Atomic structure 1  Nucleus is the central part of an atom and contains protons and neutrons. A proton is positively charged particle, while the neutron has the same mass as the proton, but has no charge. Therefore ,nucleus of an atom is positively charged. atomic weight = no. of protons + no. of neutrons An electron is a negatively charged particle having negligible mass. The charge on an electron is equal but opposite to that on a proton. Also the number of electrons is equal to the number of protons in an atom under ordinary conditions. Therefore an atom is neutral as a whole. atomic number = no. of protons or electrons in an atom The number of electrons in any orbit is given by 2n2 where n is the number of the orbit. For example, I orbit contains 2x12 =2 electrons II orbit contains 2x22 = 8 electrons III orbit contains 2x32 = 18 electrons and so on The last orbit cannot have more than 8 electrons. The last but one orbit cannot have more than 18 electrons. Positive and negative ions Protons and electrons are equal in number hence if an atom loses an electron it has lost negative charge therefore it becomes positively charged and is referred as positive ion. If an atom gains an electron it becomes negatively charged and is referred to as negative ion. Valence electrons The electrons in the outermost orbit of an atom are known as valence electrons. The outermost orbit can have a maximum of 8 electrons. The valence electrons determine the physical and chemical properties of a material. 2  When the number of valence electrons of an atom is less than 4, the material is usually a metal and a conductor. Examples are sodium, magnesium and aluminium, which have 1,2 and 3 valence electrons respectively. When the number of valence electrons of an atom is more than 4, the material is usually a non-metal and an insulator. Examples are nitrogen, sulphur and neon, which have 5,6 and 8 valence electrons respectively. When the number of valence electrons of an atom is 4 the material has both metal and non-metal properties and is usually a semi-conductor. Examples are carbon, silicon and germanium. Free electrons The valence electrons of different material possess different energies. The greater the energy of a valence electron, the lesser it is bound to the nucleus. In certain substances, particularly metals, the valence electrons possess so much energy that they are very loosely attached to the nucleus. The loosely attached valence electrons move at random within the material and are called free electrons. The valence electrons, which are loosely attached to the nucleus, are known as free electrons. Energy bands In case of a single isolated atom an electron in any orbit has definite energy. When atoms are brought together as in solids, an atom is influenced by the forces from other atoms. Hence an electron in any orbit can have a range of energies rather than single energy. These range of energy levels are known as Energy bands. Within any material there are two distinct energy bands in which electrons may exist viz Valence band and conduction band. 3  Energy level Conduction band Forbidden gap Valence band Figure1.2 Energy level diagram The range of energies possessed by valence electrons is called valence band. The range of energies possessed by free electrons is called conduction band. Valence band and conduction band are separated by an energy gap in which no electrons normally exist this gap is called forbidden gap. Electrons in conduction band are either escaped from their atoms (free electrons) or only weakly held to the nucleus. Thereby by the electrons in conduction band may be easily moved around within the material by applying relatively small amount of energy. (either by increasing the temperature or by focusing light on the material etc. ) This is the reason why the conductivity of the material increases with increase in temperature. But much larger amount of energy must be applied in order to extract an electron from the valence band because electrons in valence band are usually in the normal orbit around a nucleus. For any given material, the forbidden gap may be large, small or non-existent. Classification of materials based on Energy band theory Based on the width of the forbidden gap, materials are broadly classified as conductors, Insulators and semiconductors. Conduction Conduction Conduction band band band Forbidden overlap Forbidden Gap Gap EG =1eV EG =6eV Valence Valence Valence band band band (a) Conductor (b) Insulator (c) Semiconductor Conductors 4  Conductors are those substances, which allow electric current to pass through them. Example: Copper, Al, salt solutions, etc. In terms of energy bands, conductors are those substances in which there is no forbidden gap. Valence and conduction band overlap as shown in fig (a). For this reason, very large number of electrons are available for conduction even at extremely low temperatures. Thus, conduction is possible even by a very weak electric field. Insulators Insulators are those substances, which do not allow electric current to pass through them. Example: Rubber, glass, wood etc. In terms of energy bands, insulators are those substances in which the forbidden gap is very large. Thus valence and conduction band are widely separated as shown in fig (b). Therefore insulators do not conduct electricity even with the application of a large electric field or by heating or at very high temperatures. Semiconductors Semiconductors are those substances whose conductivity lies in between that of a conductor and Insulator. Example: Silicon, germanium, Cealenium, Gallium, arsenide etc. In terms of energy bands, semiconductors are those substances in which the forbidden gap is narrow. Thus valence and conduction bands are moderately separated as shown in fig(C). In semiconductors, the valence band is partially filled, the conduction band is also partially filled, and the energy gap between conduction band and valence band is narrow. Therefore, comparatively smaller electric field is required to push the electrons from valence band to conduction band. At low temperatures the valence band is completely filled and conduction band is completely empty. Therefore, at very low temperature a semi-conductor actually behaves as an insulator. Conduction in solids 5  Conduction in any given material occurs when a voltage of suitable magnitude is applied to it, which causes the charge carriers within the material to move in a desired direction. This may be due to electron motion or hole transfer or both. Electron motion Free electrons in the conduction band are moved under the influence of the applied electric field. Since electrons have negative charge they are repelled by the negative terminal of the applied voltage and attracted towards the positive terminal. Hole transfer Hole transfer involves the movement of holes. Holes may be thought of positive charged particles and as such they move through an electric field in a direction opposite to that of electrons. I I + + V V (a) Conductor (b) Semiconductor Flow of electrons Flow of electrons Flow of current Flow of holes Flow of current In a good conductor (metal) as shown in fig (a) the current flow is due to free electrons only. In a semiconductor as shown in fig (b). The current flow is due to both holes and electrons moving in opposite directions. The unit of electric current is Ampere (A) and since the flow of electric current is constituted by the movement of electrons in conduction band and holes in valence band, electrons and holes are referred as charge carriers. Classification of semiconductors Semiconductors are classified into two types. 6  a) Intrinsic semiconductors. b) Extrinsic semiconductors. a) Intrinsic semiconductors A semiconductor in an extremely pure form is known as Intrinsic semiconductor. Example: Silicon, germanium. Both silicon and Germanium are tetravalent (having 4 valence electrons). Each atom forms a covalent bond or electron pair bond with the electrons of neighboring atom. The structure is shown below. Silicon or Germanium Valence electron Covalent bond Figure1.3. Crystalline structure of Silicon (or Germanium) At low temperature At low temperature, all the valence electrons are tightly bounded the nucleus hence no free electrons are available for conduction. The semiconductor therefore behaves as an Insulator at absolute zero temperature. 7 At room temperature Free electron Valence electron Holes Figure 1.4. Crystalline structure of Silicon (or Germanium) at room temperature At room temperature, some of the valence electrons gain enough thermal energy to break up the covalent bonds. This breaking up of covalent bonds sets the electrons free and are available for conduction. When an electron escapes from a covalent bond and becomes free electrons a vacancy is created in a covalent bond as shown in figure above. Such a vacancy is called Hole. It carries positive charge and moves under the influence of an electric field in the direction of the electric field applied. Numbers of holes are equal to the number of electrons since, a hole is nothing but an absence of electrons. Extrinsic Semiconductor When an impurity is added to an Intrinsic semiconductor its conductivity changes. This process of adding impurity to a semiconductor is called Doping and the impure semiconductor is called extrinsic semiconductor. Depending on the type of impurity added, extrinsic semiconductors are further classified as n-type and p-type semiconductor. 8 n-type semiconductor S S S i i i free e- S A S i s i S S S i i i Figure 1.5 n-type semiconductor Conduction band Forbidden gap Fermi level Valence band Figure1.6 Energy band diagram for n-type semiconductor When a small current of Pentavalent impurity is added to a pure semiconductor it is called as n-type semiconductor. Addition of Pentavalent impurity provides a large number of free electrons in a semiconductor crystal. Typical example for pentavalent impurities are Arsenic, Antimony and Phosphorus etc. Such impurities which produce n-type semiconductors are known as Donor impurities because they donate or provide free electrons to the semiconductor crystal. To understand the formation of n-type semiconductor, consider a pure silicon crystal with an impurity say arsenic added to it as shown in figure 1.5. We know that a silicon atom has 4 valence electrons and Arsenic has 5 valence electrons. When Arsenic is added as impurity to silicon, the 4 valence electrons of silicon make co-valent bond with 4 valence electrons of Arsenic. 9  The 5th Valence electrons finds no place in the covalent bond thus, it becomes free and travels to the conduction band as shown in figure. Therefore, for each arsenic atom added, one free electron will be available in the silicon crystal. Though each arsenic atom provides one free electrons yet an extremely small amount of arsenic impurity provides enough atoms to supply millions of free electrons. Due to thermal energy, still hole election pairs are generated but the number of free electrons are very large in number when compared to holes. So in an n-type semiconductor electrons are majority charge carriers and holes are minority charge carriers. Since the current conduction is pre-dominantly by free electrons( -vely charges) it is called as n-type semiconductor( n- means –ve). p-type semiconductor S S S i i i hole S G S i a i S S S i i i Figure 1.7 p-type semiconductor 10  Conduction band Forbidden gap Fermi level Valence band Figure 1.8 Energy band diagram for p-type semiconductor When a small amount of trivalent impurity is added to a pure semiconductor it is called p-type semiconductor. The addition of trivalent impurity provides large number of holes in the semiconductor crystals. Example: Gallium, Indium or Boron etc. Such impurities which produce p-type semiconductors are known as acceptor impurities because the holes created can accept the electrons in the semi conductor crystal. To understand the formation of p-type semiconductor, consider a pure silicon crystal with an impurity say gallium added to it as shown in figure 1.7. We know that silicon atom has 4 valence electrons and Gallium has 3 electrons. When Gallium is added as impurity to silicon, the 3 valence electrons of gallium make 3 covalent bonds with 3 valence electrons of silicon. The 4th valence electrons of silicon cannot make a covalent bond with that of Gallium because of short of one electron as shown above. This absence of electron is called a hole. Therefore for each gallium atom added one hole is created, a small amount of Gallium provides millions of holes. Due to thermal energy, still hole-electron pairs are generated but the number of holes are very large compared to the number of electrons. Therefore, in a p-type semiconductor holes are majority carriers and electrons are minority carriers. Since the current conduction is predominantly by hole( + charges) it is called as p-type semiconductor( p means +ve) 11 Drift and Diffusion current The flow of current through a semiconductor material is normally referred to as one of the two types. Drift current If an electron is subjected to an electric field in free space it will accelerate in a straight line form the –ve terminal to the + ve terminal of the applied voltage. However in the case of conductor or semiconductor at room temperature, a free electrons under the influence of electric field will move towards the +ve terminal of the applied voltage but will continuously collide with atoms all the ways as shown in figure 1.9. Electron drift due to field conduction when electric field is semiconductor present + Conduction Applied voltage when no electric field is applied Figure 1.9 Each time, when the electron strikes an atom, it rebounds in a random direction but the presence of electric field doesnot stop the collisions and random motion. As a result the electrons drift in a direction of the applied electric field. The current produced in this way is called as Drift current and it is the usual kind of current flow that occurs in a conductor. Diffusion current The directional movement of charge carriers due to their concentration gradient produces a component of current known as Diffusion current. The mechanism of transport of charges in a semiconductor when no electric field is applied called diffusion. It is encountered only in semiconductors and is normally absent in conductors. 12 heavy concentration of less concentration electrons electrons Diffusion current Even distribution Net diffusion current is zero With no applied voltage if the number of charge carriers (either holes or electrons) in one region of a semiconductor is less compared to the rest of the region then there exist a concentration gradient. Since the charge carriers are either all electrons or all holes they sine polarity of charge and thus there is a force of repulsion between them. As a result, the carriers tend to move gradually or diffuse from the region of higher concentration to the region of lower concentration. This process is called diffusion and electric current produced due to this process is called diffusion current. This process continues until all the carriers are evenly distributed through the material. Hence when there is no applied voltage, the net diffusion current will be zero. 13 Fermi-level Fermi level indicates the level of energy in the forbidden gap. 1. Fermi-level for an Intrinsic semiconductor Energy level Conduction band EC Ef Fermilevel Forbidden gap EV Valence band EC Conduction band energy level EV Valence band energy level Ef fermi level We know that the Intrinsic semiconductor acts as an insulator at absolute zero temperature because there are free electrons and holes available but as the temperature increases electron hole pairs are generated and hence number of electrons will be equal to number of holes. Therefore, the possibility of obtaining an electron in the conduction band will be equal to the probability of obtaining a hole in the valence band. If Ec is the lowest energy level of Conduction band and Ev is the highest energy level of the valence band then the fermi level Ef is exactly at the center of these two levels as shown above. 14 2. Fermi-level in a semiconductors having impurities (Extrinsic) a) Fermi-level for n-type Semiconductor Let a donar impurity be added to an Intrinsic semiconductor then the donar energy level (ED) shown by the dotted lines is very close to conduction band energy level (Ec). Therefore the unbonded valence electrons of the impurity atoms can very easily jump into the conduction band and become free electros thus, at room temperature almost all the extra electrons of pentavalent impurity will jump to the conduction band. The donar energy level (ED) is just below conduction band level (Ec) as shown in figure1.10(a). Due to a large number of free electrons, the probability of electrons occupying the energy level towards the conduction band will be more hence, fermi level shifts towards the conduction band. Conduction band EC ED moves Ef upward Fermi level EV Valence band ED Energy level of donar impurity Figure 1.10 (a) Energy level diagram for n-type semiconductor 15 b) Fermi-level for P-type semiconductor Let an acceptor impurity be added to an Intrinsic semiconductor then the acceptor energy level (Ea) shown by dotted lines is very close to the valence band shown by dotted lines is very close to the valence band energy level (Ev). Therefore the valence band electrons of the impurity atom can very easily jump into the valence band thereby creating holes in the valence band. Conduction band EC Fermi level Ef EA EV Valence band EA Energy level of acceptor impurity Figure 1.11 (b) Energy level diagram for P-type semiconductor The acceptor energy level (EA) is just above the valence band level as shown in figure 1.11 (b). Due to large number of holes the probability of holes occupying the energy level towards the valence band will be more and hence, the fermi level gets shifted towards the valence band. 16 HALL EFFECT If a piece of metal or semiconductor carrying a current I is placed in a transverse magnetic field B then an electric field E is induced in the direction perpendicular to both I and B. This phenomenon is known as Hall effect. Y(+ve) Surface-2 + + + + + + + + d I VH w X (+ve) B Surface -1 Z (+ve) Hall effect is normally used to determine whether a semi-conductor is n-type or p-type. To find whether the semiconductor is n-type or p-type i) In the figure. above, If I is in the +ve X direction and B is in the +ve Z direction, then a force will be exerted on the charge carriers (holes and electrons) in the –ve Y direction. ii) This force is independent of whether the charge carriers are electrons or holes. Due to this force the charge carriers ( holes and electrons) will be forced downward towards surface –1 as shown. iii) If the semiconductor is N-type, then electrons will be the charge carriers and these electrons will accumulate on surface –1 making that surface –vely charged with respect to surface –2. Hence a potential called Hall voltage appears between the surfaces 1 and 2. iv) Similarly when surface –1 is positively charged with respect to surface –2, then the semiconductor is of P-type. In this way, by seeing the polarity of Hall voltage we can determine whether the semiconductor is of P-type or N-type. 17 Applications of Hall effect Hall effect is used to determine, carrier concentration, conductivity and mobility. The sign of the current carrying charge. Charge density. It is used as magnetic field meter. Carrier lifetime (τ) In a pure semiconductor, we know that number of holes are equal to the number of electrons. Thermal agitation however, continues to produce new hole electron pairs while other hole-electron pair disappear as a result of recombination. On an average, a hole will exist for τp second and an electron will exist for τn second before recombination. This time is called the carrier lifetime or Mean lifetime. The average time an electron or hole can exist in the free state is called carrier lifetime. 18 CHAPTER 2 SEMICONDUCTOR DIODE When a p-type semiconductor material is suitably joined to n-type semiconductor the contact surface is called a p-n junction. The p-n junction is also called as semiconductor diode. p n ++ (b) (a) Depletion region Fig. 2.0 (a) p-n junction Fig 2.0 (b) symbolic representation The left side material is a p-type semiconductor having –ve acceptor ions and +vely charged holes. The right side material is n-type semiconductor having +ve donor ions and free electrons. Suppose the two pieces are suitably treated to form pn junction, then there is a tendency for the free electrons from n-type to diffuse over to the p-side and holes from p-type to the n-side. This process is called diffusion. As the free electrons move across the junction from n-type to p-type, +ve donor ions are uncovered. Hence a +ve charge is built on the n-side of the junction. At the same time, the free electrons cross the junction and uncover the –ve acceptor ions by filling in the holes. Therefore a net –ve charge is established on p-side of the junction. When a sufficient number of donor and acceptor ions is uncovered further diffusion is prevented. Thus a barrier is set up against further movement of charge carriers. This is called potential barrier or junction barrier Vo. The potential barrier is of the order of 0.1 to 0.3V. Note: outside this barrier on each side of the junction, the material is still neutral. Only inside the barrier, there is a +ve charge on n-side and –ve charge on p-side. This region is called depletion layer. 2.1 Biasing: Connecting a p-n junction to an external d.c. voltage source is called 19  biasing. 1. Forward biasing 2. Reverse biasing 1. Forward biasing When external voltage applied to the junction is in such a direction that it cancels the potential barrier, thus permitting current flow is called forward biasing. To apply forward bias, connect +ve terminal of the battery to p-type and –ve terminal to n-type as shown in fig.2.1 below. The applied forward potential establishes the electric field which acts against the field due to potential barrier. Therefore the resultant field is weakened and the barier height is reduced at the junction as shown in fig. 2.1. Since the potential barrier voltage is very small, a small forward voltage is sufficient to completely eliminate the barrier. Once the potential barrier is eliminated by the forward voltage, junction resistance becomes almost zero and a low resistance path is established for the entire circuit. Therefore current flows in the circuit. This is called forward current. p n no external field External field Fig.2.1 forward biasing of p-n junction 20 2. Reverse biasing When the external voltage applied to the junction is in such a direction the potential barrier is increased it is called reverse biasing. To apply reverse bias, connect –ve terminal of the battery to p-type and +ve terminal to n-type as shown in figure below. The applied reverse voltage establishes an electric field which acts in the same direction as the field due to potential barrier. Therefore the resultant field at the junction is strengthened and the barrier height is increased as shown in fig.2.2. The increased potential barrier prevents the flow of charge carriers across the junction. Thus a high resistance path is established for the entire circuit and hence current does not flow. p n external field no external field Fig.2.2 Reverse biasing of p-n junction 21 2.2 Volt- Ampere characteristics(V-I) R A diode V V (i) IF(mA) Break over Voltage VR Knee voltage VF IR(μA) (ii) Fig. 2.3 V-I characteristics of p-n junction diode. (i) Circuit diagram (ii) Characteristics The V-I characteristics of a semiconductor diode can be obtained with the help of the circuit shown in fig. 2.3 (i) The supply voltage V is a regulated power supply, the diode is forward biased in the circuit shown. The resistor R is a current limiting resistor. The voltage across the diode is measured with the help of voltmeter and the current is recorded using an ammeter. By varying the supply voltage different sets of voltage and currents are obtained. By plotting these values on a graph, the forward characteristics can be obtained. It can be noted from the graph the current remains zero till the diode voltage attains the barrier potential. For silicon diode, the barrier potential is 0.7 V and for Germanium diode, it is 0.3 V. The barrier potential is also called as knee voltage or cur-in voltage. 22  The reverse characteristics can be obtained by reverse biasing the diode. It can be noted that at a particular reverse voltage, the reverse current increases rapidly. This voltage is called breakdown voltage. 2.3 Diode current equation The current in a diode is given by the diode current equation I = I0( e V/ηVT –1) Where, I------ diode current I0------ reverse saturation current V------ diode voltage η------- semiconductor constant =1 for Ge, 2 for Si. VT------ Voltage equivalent of temperature= T/11,600 (Temperature T is in Kelvin) Note----- If the temperature is given in 0C then it can be converted to Kelvin by the help of following relation, 0C+273 = K 2.4 Diode equivalent circuit It is generally profitable to replace a device or system by its equivalent circuit. Once the device is replaced by its equivalent circuit, the resulting network can be solved by traditional circuit analysis technique. switch rf If VF Vo VF (i) (ii ) Fig.2.4 Diode equivalent circuit. (i) symbol (ii) equivalent circuit The forward current If flowing through the diode causes a voltage drop in its internal resistance rf. Therefore the forward voltage VF applied across the actual diode has to overcome 1. potential barrier Vo 2. internal drop If rf Vf = Vo + If rf For silicon diode Vo=0.7V whereas for Germanium diode Vo = 0.3 V. For ideal diode rf =0. 23 24.1 Basic Definitions 1.Knee voltage or Cut-in Voltage. It is the forward voltage at which the diode starts conducting. 2. Breakdown voltage It is the reverse voltage at which the diode (p-n junction) breaks down with sudden rise in reverse current. 3. Peak-inverse voltage (PIV) It is the max. reverse voltage that can be applied to a p-n junction without causing damage to the junction. If the reverse voltage across the junction exceeds its peak-inverse voltage, then the junction exceeds its Peak-inverse voltage, then the junction gets destroyed because of excessive heat. In rectification, one thing to be kept in mind is that care should be taken that reverse voltage across the diode during –ve half cycle of a.c. doesnot exceed the peak-inverse voltage of the diode. 4. Maximum Forward current It is the Max. instantaneous forward current that a p-n junction can conduct without damaging the junction. If the forward current is more than the specified rating then the junction gets destroyed due to over heating. 5.Maximum Power rating It is the maximum power that can be dissipated at the junction without damaging it. The power dissipated across the junction is equal to the product of junction current and the voltage across the junction. 24 2.5 RECTIFIERS “Rectifiers are the circuit which converts ac to dc” Rectifiers are grouped into tow categories depending on the period of conductions. 1. Half-wave rectifier 2. Full- wave rectifier. 2.5.1 Half-wave rectifier The circuit diagram of a half-wave rectifier is shown in fig. 2.5 below along with the I/P and O/P waveforms. (i) Vi t Vo π 2π t (ii) Fig. 2.5 Half wave rectifier (i) Circuit diagram (ii) waveforms The transformer is employed in order to step-down the supply voltage and also to prevent from shocks. The diode is used to rectify the a.c. signal while , the pulsating d.c. is taken across the load resistor RL. 25  During the +ve half cycle, the end X of the secondary is +ve and end Y is -ve. Thus , forward biasing the diode. As the diode is forward biased, the current flows through the load RL and a voltage is developed across it. During the –ve half-cycle the end Y is +ve and end X is –ve thus, reverse biasing the diode. As the diode is reverse biased there is no flow of current through RL thereby the output voltage is zero. 2.5.2 Efficiency of a rectifier The ratio of d.c. power to the applied imp ac power is known as rectifier efficiency. d.c. power.output Rectifier efficiency η = input.a.c. power 2.5.3Derivation of rectifier efficiency of Half wave rectifier Let V = Vmsinθ be the voltage across the secondary winding rf = diode resistance RL = load resistance d.c. power π π 1 1 VmSinθ Iav = Idc = 2π ∫0 i.dθ = 2π ∫ 0 rL + R L dθ π Vm 2π (rf + RL ) ∫0 = Sinθ dθ 2Vm Im = = 2π (rf + RL) π d.c. power Pdc = I2dc * RL 2  Im  =  ∗ RL ------------------------------ (1)  π  26 a.c. power input The a.c. power input is given by Pac = I2rms ( rf + RL) 2π 1 I rms = ∫i dθ 2 2π 0 Squaring both sides we get 2π 1 = ∫i dθ 2 2 I rms 2π 0 But i = Im Sinθ π 1 = ∫ (Im Sinθ ) dθ 2 2 I rms ( current flows through diode only for duration 0 to Π ) 2π 0 I m2 2 I rms = 4 Im I rms = 2 2 I  ∴ Pac =  m  ( r f + R L ) --------------------------------------------(2)  2  2  Im  Pdc  π  ∴η = =   * RL Pac  I m  2 ( r f + RL )  2   0.406 η = r f -------------------------------------------------(3) 1+ RL The efficiency is maximum if rf is negligible as compared to RL Therefore maximum rectifier efficiency = 40.6 % 27 2.5.4 Full-wave rectifier Full-wave rectifier are of two types 1. Centre tapped full-wave rectifier 2. Bridge rectifier 2.5.4.1Centre tapped full –wave rectifier (i) Vin Vout π 2π (ii) Fig. 2.6 Centre tapped Full wave rectifier (i) Circuit diagram (ii) waveforms The circuit diagram of a center tapped full wave rectifier is shown in fig. 2.6 above. It employs two diodes and a center tap transformer. The a.c. signal to be rectified is applied to the primary of the transformer and the d.c. output is taken across the load RL. During the +ve half-cycle end X is +ve and end Y is –ve this makes diode D 1 forward biased and thus a current i1 flows through it and load resistor RL.Diode D2 is reverse biased and the current i2 is zero. 28  During the –ve half-cycle end Y is +Ve and end X is –Ve. Now diode D 2 is forward biased and thus a current i2 flows through it and load resistor RL. Diode D1 is reversed and the current i1 = 0. Disadvantages Since, each diode uses only one-half of the transformer secondary voltage the d.c. output is comparatively small. It is difficult to locate the center-tap on secondary winding of the transformer. The diodes used must have high Peak-inverse voltage. 2.5.4.2 Bridge rectifier (i) Vout D1D3 D2D4 D1D4 t (ii) Fig. 2.7 Full wave bridge wave rectifier (i) Circuit diagram (ii) waveforms. The circuit diagram of a bridge rectifer is shown above. It uses four diodes and a transformer. During the +ve half-cycle, end A is +ve and end B is –ve thus diodes D 1 and D3 are forward bias while diodes D2 and D4 are reverse biased thus a current flows through diode D1, load RL ( C to D) and diode D3. 29  During the –ve half-cycle, end B is +ve and end A is –ve thus diodes D 2 and D4 are forward biased while the diodes D1 and D3 are reverse biased. Now the flow of current is through diode D4 load RL ( D to C) and diode D2. Thus, the waveform is same as in the case of center-tapped full wave rectifier. Advantages The need for center-taped transformer is eliminated. The output is twice when compared to center-tapped full wave rectifier. for the same secondary voltage. The peak inverse voltage is one-half(1/2) compared to center-tapped full wave rectifier. Can be used where large amount of power is required. Disadvantages It requires four diodes. The use of two extra diodes cause an additional voltage drop thereby reducing the output voltage. 2.5.6 Efficiency of Full-wave rectifier Let V = Vmsinθ be the voltage across the secondary winding I = Imsinθ be the current flowing in secondary circuit rf = diode resistance RL = load resistance dc power output Pdc = I dc2 R L -----------------------------(1) π 1 I dc = I av = 2 2π ∫ i.dθ 0 π 1 I av = 2 2π ∫ Im Sinθ.dθ 0 2I m I av = π -------------------------------------------------------- (2) 2  2I  ∴ Pdc =  m  R L  π  ------------------------------------------ (3) 30 input ac power Pac = I rms 2 ( r f + RL ) ---------------------------------------- (4) π 1 2 2π ∫0 I rms = 2i dθ Squaring both sides we get π 1 2 π ∫0 2 I rms = i dθ π 1 I 2 rms = ∫ (Im Sinθ ) 2 dθ π 0 I m2 2 I rms = 2 Im I rms = ------------------------------------------------ ----- (5) 2 2  I  ∴ Pac =  m  ( r f + R L ) --------------------------------------------(6)  2 2  2I m  Pdc  π  RL ∴η = =  * Pac  I m  2 ( r f + RL )    2 0.812 η = r f -------------------------------------------------(7) 1+ RL The efficiency will be maximum if rf is negligible as compared to RL. Maximum efficiency = 81.2 % This is the double the efficiency due to half wave rectifier. Therefore a Full-wave rectifier is twice as effective as a half-wave rectifier. 31 2.6 Comparision of Rectifiers Particulars Half wave rectifier Centre-tapped Full Bridge rectifier wave rectifier 1. No. of diodes 1 2 4 2. Idc Im / Π 2Im /Π 2Im /Π 3. Vdc Vm / Π 2Vm / Π 2Vm / Π 4.Irms Im / 2 Im /√ 2 Im /√ 2 5.Efficiency 40.6 % 81.2 % 81.2 % 6.PIV Vm 2Vm Vm 7.Ripple factor 1.21 0.48 0.48 Note: The relation between turns ratio and voltages of primary and secondary of the transformer is given by o N1 / N2 = Vp / Vs RMS value of voltage and Max. value of voltage is related by the equation.  Vrms = Vm / √2 ( for full-cycle of ac) If the type of diode is not specified then assume the diode to be of silicon type. For an ideal diode, forward resistance rf = 0 and cut-in voltage , Vγ = 0. 32 2.7 Ripple factor The pulsating output of a rectifier consists of d.c. component and a.c. component ( also known as ripple). The a.c. component is undesirable and account for the pulsations in the rectifier output. The effectiveness of a rectifier depends upon the magnitude of a.c. component in the output : the smaller this component, the more effective is the rectifier. “ The ratio of rms value of a.c. component to the d.c. component in the rectifier output is known as ripple factor” Iac r= Idc 2.7.1 Ripple factor for Half-wave rectification By definition the effective (ie rms) value of total load current is given by I rms = I ac2 + I dc2 OR I ac = 2 I rms − I dc2 Where Idc = value of dc component Iac = rms value of ac component Divide both R.H.S and L.H.S. by Idc we get I ac 1 = 2 I rms − I dc2 I dc I dc 2  I rms  r=   − 1 --------------------------------------------------(1)  I dc  I for half-wave rectification, we have I I rms = m 2 Im I dc = π Substituting above values in equation (1) we get, ripple factor r = 1.21 It is clear that a.c. component exceeds dc component in the output of a half-wave rectifier. 33 2.7.2 Ripple factor for full-wave rectification Im For full wave rectification we have Irms = 2 2I m Idc = π Substituting above values in equation (1) we get , ripple factor r = 0.48 This shows that in the output of Full-wave rectifier, the d.c. component is more than the a.c. component 2.8 FILTERS We know that the output of the rectifier is pulsating d.c. ie the output obtained by the rectifier is not pure d.c. but it contains some ac components along with the dc o/p. These ac components are called as Ripples, which are undesirable or unwanted. To minimize the ripples in the rectifier output filter circuits are used. These circuits are normally connected between the rectifier and load as shown below. Vi Vo pure dc o/p Rectifier Filter Pulsating d.c. output Filter is a circuit which converts pulsating dc output from a rectifier to a steady dc output. In otherwords, filters are used to reduce the amplitudes of the unwanted ac components in the rectifier. Note: A capacitor passes ac signal readily but blocks dc. 34 2.8.1 Types of Filters 1. Capacitor Filter (C-Filter) 2. Inductor Filter 3. Choke Input Filter (LC-filter) 4. Capacitor Input Filter (Π-filter) 2.8.2 Capacitor Filter( C-filter) (i) Vin a f e t b d c V1 o/p without filter t Vo o/p with filter a e t Fig.2.8 Capacitor filter ( C-filter) (i) Circuit diagram (ii) waveforms 35  When the Input signal rises from o to a the diode is forward biased therefore it starts conducting since the capacitor acts as a short circuit for ac signal it gets charged up to the peak of the input signal and the dc component flows through the load RL. When the input signal fall from a to b the diode gets reverse biased. This is mainly because of the voltage across the capacitor obtained during the period o to a is more when comapared to Vi. Therefore there is no conduction of current through the diode. Now the charged capacitor acts as a battery and it starts discharging through the load RL. Mean while the input signal passes through b,c,d section. When the signal reaches the point d the diode is still reverse biased since the capacitor voltage is more than the input voltage. When the signal reaches point e, the input voltage can be expected to be more than the capacitor voltage. When the input signal moves from e to f the capacitor gets charged to its peak value again. The diode gets reverse biased and the capacitor starts discharging. The final output across RL is shown in Fig. 2.8 The ripple factor for a Half-wave rectifier with C-filer is given by r= 1/2√3fCRL f-----the line frequency ( Hz) C-----capacitance ( F) RL------- Load resistance (Ω) Ripple factor for full-wave rectifier with C-filter is given by r = 1/ 4 √3 f C RL 2.8.3 Advantages of C-Filter low cost, small size and good characteristics. It is preferred for small load currents ( upto 50 mA) It is commonly used in transistor radio, batteries eliminator etc. 36 2.9 Zener Diode The reverse voltage characteristics of a semiconductor diode including the breakdown region is shown below. V Vz 0 I Fig. 2.9 Zener diode characteristics Zener diodes are the diodes which are designed to operate in the breakdown region. They are also called as Breakdown diode or Avalanche diodes. The symbol of Zener diode is shown below P N Fig. 2.10 Symbol of Zener diode The breakdown in the Zener diode at the voltage Vz may be due to any of the following mechanisms. 1. Avalanche breakdown Depletion region charge carriers striking the atoms ( ) ( ) P N -ve terminal +ve terminal minority charge carriers Fig. 2.11 Avalanche breakdown in Zener diode We know that when the diode is reverse biased a small reverse saturation current I0 flows across the junction because of the minority cariers in the depletion region. 37  The velocity of the minority charge carriers is directly proportional to the applied voltage. Hence when the reverse bias voltage is increased, the velocity of minority charge carriers will also increase and consequently their energy content will also increase. When these high energy charge carriers strikes the atom within the depletion region they cause other charge carriers to break away from their atoms and join the flow of current across the junction as shown above. The additional charge carriers generated in this way strikes other atoms and generate new carriers by making them to break away from their atoms. This cumulative process is referred to as avalanche multiplication which results in the flow of large reverse current and this breakdown of the diode is called avalanche breakdown. 2.Zener breakdown We have electric field strength = Reverse voltage/ Depletion region Depletion region ( ) ( ) P N -ve terminal +ve terminal electrons pulled out of their covalent bonds because of high intensity electric field Fig.2.12 Zener breakdown in Zener diode From the above relation we see that the reverse voltage is directly proportional to the electric field hence, a small increase in reverse voltage produces a very high intensity electric field with ina narrow Depletion region. Therefore when the reverse voltage to a diode is increased, under the influence of high intensity electric filed large numbr of electrons within the depletion region break the covalent bonds with their atoms as shown above and thus a large reverse current flows through the diode. This breakdown is referred to as Zener breakdown. 38 2.9.1 Zener voltage regulator The circuit diagram of Zener voltage regulator is shown below Rs I IZ IL Vin VZ RL Vo Fig. 2.13 Zener voltage regulator. A zener diode of breakdown voltage VZ is connected in reverse biased condition across the load RL such that it operates in breakdown region. Any fluctuations in the current are absorbed by the series resistance Rs. The Zener will maintain a constant voltage VZ ( equal to Vo) across the load unless the input voltage does not fall below the zener breakdown voltage VZ. Case(i) When input voltage Vin varies and RL is constant Rs I IZ IL Vin VZ RL Vo If the input voltage increases, the Zener diode which is in the breakdown region is equivalent to a battery VZ as shown in figure. The output voltage remains constant at VZ (equal to Vo) and the excess voltage is dropped across the series resistance RS. We know that for a zener diode under breakdown region large change in current produces very small change in voltage, thereby the output voltage remains constant. Case (ii) When Vin is constant and RL varies. Rs I IZ IL Vin VZ RL Vo 39 If there is a decrease in the load resistance RL and the input voltage remains constant then there is a increase in load current. Since Vin is constant the current cannot come from the source. This addition load current is driven from the battery VZ and we know that even for a large decrease in current the Zener output voltage Vz remains same. Hence the output voltage across the load is also constant.. 40 CHAPTER 3 TRANSISTORS A transistor is a sandwich of one type of semiconductor (P-type or n-type) between two layers of other types. Transistors are classified into two types; 1. pnp transistor pnp transistor is obtained when a n-type layer of silicon is sandwiched between two p-type silicon material. 2. npn transisitor npn transistor is obtained when a p-type layer of silicon is sandwiched between two n-type silicon materials. Figure3.1 below shows the schematic representations of a transistor which is equivalent of two diodes connected back to back. JE JC JE JC E C E C p n p n p n B B Fig 3.1: Symbolic representation pnp npn Fig 3.2: Schematic representation  The three portions of transistors are named as emitter, base and collector. The junction between emitter and base is called emitter-base junction while the junction between the collector and base is called collector-base junction.  The base is thin and tightly doped, the emitter is heavily doped and it is wider when compared to base, the width of the collector is more when compared to both base and emitter. 41  In order to distinguish the emitter and collector an arrow is included in the emitter. The direction of the arrow depends on the conventional flow of current when emitter base junction is forward biased.  In a pnp transistor when the emitter junction is forward biased the flow of current is from emitter to base hence, the arrow in the emitter of pnp points towards the base. 3.1 Operating regions of a transistor A transistor can be operated in three different regions as a) active region b) saturation region c) cut-off region Active region E JE B JC C p n p VEB VCB Fig 3.3: pnp transistor operated in active region The transistor is said to be operated in active region when the emitter-base junction is forward biased and collector –base junction is reverse biased. The collector current is said to have two current components one is due to the forward biasing of EB junction and the other is due to reverse biasing of CB junction. The collector current component due to the reverse biasing of the collector junction is called reverse saturation current (ICO or ICBO) and it is very small in magnitude. Saturation region E JE B JC C p n p VEB VCB Fig 3.4: pnp transistor operated in Saturation region 42 Transistor is said to be operated in saturation region when both EB junction and CB junction are forward biased as shown. When transistor is operated in saturation region I C increases rapidly for a very small change in VC. Cut-off region E JE B JC C p n p VEB VCB Fig 3.5: pnp transistor operated in Cut-off region When both EB junction and CB junction are reverse biased, the transistor is said to be operated in cut-off region. In this region, the current in the transistor is very small and thus when a transistor in this region it is assumed to be in off state. 3.2 Working of a transistor (pnp) E JE B JC C IE IE IC IC p n p IB VEB VCB Fig 3.6 Transistor in active region Consider a pnp transistor operated in active region as shown in Figure 3.6 Since the EB junction is forward biased large number of holes present in the emitter as majority carriers are repelled by the +ve potential of the supply voltage VEB and they move towards the base region causing emitter current IE. Since the base is thin and lightly doped very few of the holes coming from the emitter recombine with the electrons causing base current IB and all the remaining holes move towards the collector. Since the CB junction is reverse 43  biased all the holes are immediately attracted by the –ve potential of the supply VCB. Thereby giving rise to collector current IC. Thus we see that IE = IB + IC -----------------(1) (By KVL) Since the CB junction is reverse biased a small minority carrier current ICO flows from base to collector. 3.3 Current components of a transistor JE JC IPE IPC (hole current) IPB (hole current) IE INE (e- current) ICO IC IB VEB VCB Fig 3.7:Current components of a transistor Fig 3.7 above shows a transistor operated in active region. It can be noted from the diagram the battery VEB forward biases the EB junction while the battery VCB reverse biases the CB junction. As the EB junction is forward biased the holes from emitter region flow towards the base causing a hole current IPE. At the same time, the electrons from base region flow towards the emitter causing an electron current INE. Sum of these two currents constitute an emitter current IE = IPE +INE. The ratio of hole current IPE to electron current INE is directly proportional to the ratio of the conductivity of the p-type material to that of n-type material. Since, emitter is highly doped when compared to base; the emitter current consists almost entirely of holes. Not all the holes, crossing EB junction reach the CB junction because some of the them combine with the electrons in the n-type base. If IPC is the hole current at (Jc) CB junction. There will be a recombination current IPE - IPC leaving the base as shown in figure 3.7. If emitter is open circuited, no charge carriers are injected from emitter into the base and hence emitter current IE =o. Under this condition CB junction acts a a reverse biased 44 diode and therefore the collector current ( IC = ICO) will be equal to te reverse saturation current. Therefore when EB junction is forward biased and collector base junction is reverse biased the total collector current IC = IPC +ICO. 3.4 Transistor configuration We know that, transistor can be used as an amplifier. For an amplifier, two terminals are required to supply the weak signal and two terminals to collect the amplified signal. Thus four terminals are required but a transistor is said to have only three terminals Therefore, one terminal is used common for both input and output. This gives rise to three different combinations. 1. Common base configuration (CB) 2. Common emitter configuration (CE) 3. Common collector configuration (CC) 1. CB configuration A simple circuit arrangement of CB configuration for pnp transistor is shown below. IE IC Vi IB RL Vout VEB VCB Fig 3.8:CB configuration In this configuration, base is used as common to both input and output. It can be noted that the i/p section has an a.c. source Vi along with the d.c. source VEB. The purpose of including VEB is to keep EB junction always forward biased (because if there is no VEB then the EB junction is forward biased only during the +ve half-cycle of the i/p and reverse biased during the –ve half cycle). In CB configuration, IE –i/p current, IC –o/p current. Current relations 1.current amplification factor (α) It is defined as the ratio of d.c. collector current to d.c. emitter current IO α= IE 2. Total o/p current We know that CB junction is reverse biased and because of minority charge carriers a small reverse saturation current ICO flows from base to collector. 45 IC = IE + ICO Since a portion of emitter current IE flows through the base ,let remaining emitter current be αIE. IC = αIE + ICo Characteristics 1. Input characteristics IE VCB=10V VCB=5V VEB Fig 3.9: Input characteristics I/p characteristics is a curve between IE and emitter base voltage VEB keeping VCB constant. IE is taken along y-axis and VEB is taken along x-axis. From the graph following points can be noted. 1. For small changes of VEB there will be a large change in IE. Therefore input resistance is very small. 2. IE is almost independent of VCB 3. I/P resistance , Ri = ΔVEB / Δ IE VCB =constant 2. Output characteristics IC Active region IE=3 mA IE =2 mA Saturation IE = 1 mA region IE = 0 Cut-off region VCB Fig 3.10:Output characteristics o/p characteristics is the curve between IC and VCB at constant IE. The collector current IC is taken along y-axis and VCB is taken along x-axis. It is clear from the graph that the o/p current IC remains almost constant even when the voltage VCB is increased. 46 i.e. , a very large change in VCB produces a small change in IC. Therefore, output resistance is very high. O/p resistance Ro = ΔVEB / Δ IC IE = constant Region below the curve IE =0 is known as cut-off region where IC is nearly zero. The region to the left of VCB =0 is known as saturation region and to the right of VCB =0 is known as active region. 2. CE configuration IC RL Vout IB Vi IE VEB VCE Fig 3.11:CE configuration In this configuration the input is connected between the base and emitter while the output is taken between collector and emitter. For this configuration IB is input current and IC is the output current. 1. Current amplification factor (β) It is the ratio of d.c. collector current to d.c. base current. i.e., β = IC / IB 2. Relationship between α and β IC We know that α = IE IC α= IB + IC divide both numerator and denominator of RHS by IC, we get 1 α = IB +1 IC 1 α = 1 +1 β 47  ( IC / IB = β ) β α = 1+ β Also we have α (1 + β ) = β α + αβ = β α = β − αβ α = β (1 − α ) α β = 1− α Derivation of Total output current IC We have I C = α I E + I CBO β IC = I E + I CBO 1+ B β I E + (1 + β ) I CBO IC = 1+ β Ic = β I B + (1 + β ) I CBO Transistor Characteristics 1. i/p characteristics IB VCE=10V VCE=5V VEB Fig 3.11: i/p characteristics 48 Input characteristics is a curve between EB voltage (VEB ) and base current (IB ) at constant VCE. From the graph following can be noted. 1. The input characteristic resembles the forward characteristics of a p-n junction diode. 2. For small changes of VEB there will be a large change in base current IB. i.e., input resistance is very small. 3. The base current is almost independent of VCE. 4. Input resistance , Ri = ΔVEB / Δ IB V CE = constant 2. Output characteristics IC (mA) Active region 30 μA 20 μA 10 μA IB =0μA Cut-off region V CE(volts) Fig 3.12: Output characteristics It is the curve between VCE and IC at constant IB. From the graph we can see that, 1. Very large changes of VCE produces a small change in IC i.e output resistance is very high. 2. output resistance Ro = ΔVCE / ΔIC │IB = constant Region between the curve IB =0 is called cut-off region where IB is nearly zero. Similarly the active region and saturation region is shown on the graph. 3. CC configuration IE RL Vout IB Vi IC VCB VCE Fig 3.13: CC configuration In this configuration the input is connected between the base and collector while the output is taken between emitter and collector. Here IB is the input current and IE is the output current. 49 Current relations 1. Current amplification factor (γ) 2. Relationship between α β and γ IE γ= IB I B + IC γ= IB divide both Numerator and denominator by IB IC 1+ IB γ = 1 γ = 1+ β ( β = IC / IB) α γ = 1+ 1− α 1 γ = ------------------------------------- 1− α Derivation of total output current IE We know that IC = α I E + I CBO IE = IB + IC IE = IB + αIE + ICBO IE(1-α ) = IB + ICBO IB I IE = + CBO 1− α 1− α 50 IE = γIB + γICBO IE = γ (IB + ICBO) ----------------------------- 51 3.5 Comparison between CB, CC and CE configuration Characteristics CB CE CC 1. Input reistance (Ri) low low high 2. Output resistance (Ro) high high low 3. Current amplification β α 1 factor α = β = γ = 1+ β 1− α 1− α 4. Total output current Ic = β I B + (1 + β ) I CBO IE = γIB + γICBO I C = α I E + I CBO 5. Phase relationship between input and output In-phase in-phase Out-of phase For high frequency For audio frequency For impedance 6. Applications applications matching applications Less than unity Greater than unity Very high 7. Current gain Very high Grater than unity Less than unity 8. Voltage gain 52 3.6 Transistor as an amplifier IC RL Vout IB Vi ` IE VEB VCB Fig 3.13: Transistor as an amplifier Consider a npn transistor in CE configuration as shown above along with its input characteristics. A transistor raises the strength of a weak input signal and thus acts as an amplifier. The weak signal to be amplified is applied between emitter and base and the output is taken across the load resistor RC connected in the collector circuit. In order to use a transistor as an amplifier it should be operated in active region i.e. emitter junction should be always FB and collector junction should be RB. Therefore in addition to the a.c. input source Vi two d.c. voltages VEB and VCE are applied as shown. This d.c. voltage is called bias voltage. As the input circuit has low resistance, a small change in te signal voltage Vi causes a large change in the base current thereby causing the same change in collector current (because IC = βIB). The collector current flowing through a high load resistance RC produces a large voltage across it. Thus a weak signal applied at the input circuit appears in the amplified form at the output. In this way transistor acts as an amplifier. Example: Let RC = 5KΩ, Vin =1V, IC =1mA then output V=ICRC =5V 53 3.7 Bias stabilization The process of making operating point independent of temperature changes or variation in transistor parameters is called the stabilization. We know that for transistor to operate it should be properly biased so that we can have a fixed operating point. To avoid any distortions, the Q-point should be at the center of the load line. But in practice this Q-point may shift to any operating region (saturation or cur-off region) making the transistor unstable. Therefore in order to avoid this, biasing stability should be maintained. 3.8 Causes for Bias instability Bias instability occurs mainly due to two reasons. 1. Temperature 2. Current gain 1. Temperature (T) The temperature at the junctions of a transistor depends on the amount of current flowing through it. Due to increase in temperature following parameters of a transistor will change. (a)base-emitter voltage (VBE) VBE increases at a rate of 2.4mV/0C. With increase in temperature the base current IB will increase and since IC= βIB, IC is also increased hence, changing the Q-point. (b) Reverse saturation current ( ICBO) We know that IC = βIB + (1+β) ICBO where ICBO is the reverse saturation current. As the temperature increases ICBO increases there by increase in IC and hence changing the Q- point. 2. Current gain (β) In the process of manufacturing the transistors different transistors of same type may have different parameters ( i.e. if we take two transistor units of same type and use them in the circuit there is a change in the β value in actual practice ). The biasing circuit will be designed according to the required β value but due to the change in β from unit to unit the operating point may shift. 54 3.9 Cascading transistor amplifiers When the amplification provided by a single stage amplifier is not suffiecient for a particular purpose or when the input and output impedance is not of the correct magnituded for the required application then two or more amplifiers are connected in cascade as shown below. Fig 3.14:Cascading transistor amplifiers Here the output of amplifier 1 is connected as the input of amplifier 2. Example: The gain of a single amplifier is not sufficient to amplify a signal from a weak source such as microphone to a level which is suitablefor the operation of another circuit as loud speaker. In such cases, amplifiers are used. When amplifiers are cascaded, individual amplifiers provides required amplification and input and output provide impedance matching. Decibel (dB) Many a times it is convenient to represent the gain of an amplifier on a log scale instead of a linear scale. The unit of this log scale is called decibel. Power gain =loge( Pout /Pin ) bel Power gain in dB =10 log10( Pout /Pin ) dB Voltage gain =20log10( Vout /Vin ) dB Current gain = 20log10(Iout / Iin ) dB Note: For a multistage amplifier if AV1, AV2, and AV3 are the voltage gains of amplifier 1,2, and 3 respectively then the overall voltage gain AV = AV1 x AV2 x AV3. If it is expressed in dB the AV(dB) = AV1(dB) + AV2(dB) +AV3(dB) Similarly for four or more stages. 55 3.10 Single stage RC coupled Amplifier VCC Vo R1 RC CC Vo t RS R2 RE RL Vi Fig 3.15:single stage RC-coupled amplifier Figure above shows a practical circuit of a single stage RC coupled amplifier.The different circuit components and their functions are as described below. a. Input capacitor(Cin)- This capacitor is used to couple the input signal to the base of the transistor if it is not used, the signal source resistance R S gets in parallel with R2 thus changing the bias. The capacitor Cin blocks any d.c. component present in the signal and passes only a.c. signal for amplification. b. Biasing circuit –The resistances R1, R2 and RE forms the biasing and stabilization circuit for the CE amplifier. It sets the proper operating point for the amplifier. c. Emitter bypass capacitor (CE)-This capacitor is connected in parallel with the emitter resistance RE to provide low reactance path to the amplified a.c. signal. If it is not used, the amplified a.c. signal passing through RE will cause voltage drop across itthereby reducing the output voltage of the amplifier. d. Coupling capacitor(Cc)- This capacitor couples the output of the amplifier to the load or to the next stage of the amplifier. If it is not used, the biasing conditions of the next stage will change due to the parallel effect of collector resistor RC. i.e. RC will come in parallel with the resistance R1 of the biasing network of the next stage thus changing the biasing conditions of the next stage amplifier. Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 56 3.11 Two stage RC coupled amplifier VCC R1 RC CC R11 RC 1 CC1 RS R2 RE CE R21 CE 1 RL Vi RE 1 Stage-1 Stage-2 Fig 3.16: Two stage RC coupled Amplifier Figure above shows the circuit diagram of a two stage RC coupled amplifier. The coupling capacitor CC connects the output of the first stage to the input of the second stage. Since the coupling from one stage to the next stage is achieved by coupling capacitor along with a shunt resistor the amplifier is called RC coupled amplifier.. The input signal is first applied to the transistor T1 and output is taken at the collector of T1. The signal at the output will be 1800 out of phase when compared to the input. The output is taken across RC with the help of a coupling capacitor. This signal is fed as input to the next stage i.e transistor T2. The signal is amplified further and the amplified output is taken across Rc1 of T2. The phase of the signal is reversed again. The output is amplified twice and its is amplified replica of the input signal. 3.12 Frequency response in amplifer Frequency response is the curve between the gain of the amplifier (A = Vo / Vi ) verses the frequency of the input signal. The frequency response of a typical RC- coupled amplifier is shown below. Frequency response has 3 regions. 1. Low frequency range 2. Mid frequency range 3. High frequency range Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 57  Gain in dB LFR MFR HFR f1 f2 freq(Hz) Fig 3.16: Frequency response in amplifer Low frequency range (< 50 Hz) We have 1 Xc = where XC ----- reactance of capacitor.; 2π RC f-----frequency Since frequency is inversely proportional to the reactance, the reactance of the coupling capacitor CC will be quite high at low frequencies. Hence very small amount of signal will pass through one stage to the next stage. Moreover CE cannot shunt the emitter resistance RE effectively because of its large reactance at low frequency. These two factors causes the fall of voltage gain at low frequencies. Mid frequency range (50Hz –20KHz) In this range of frequencies, voltage gain of the amplifier is constant. The effect of coupling capacitor in this range is as such to maintain a uniform voltage gain. High frequency range (> 20 KHz) In this range of frequency, the reactance of the coupling capacitor CC is very small and it behaves as a short circuit. This increases the loading effect of next stage ( RC will comes in parallel with R1) and reduces the voltage gain. This reduces the current amplification there by the voltage drops at high frequencies. Advantages of RC coupled amplifer 1. Low cost-Because only resistors and capacitors are used for biasing and coupling which are cheap. 2. Compact-Because modern resistor and capacitors are small and light 3. Good frequency response- The gain is constant over the audio frequency range and hence suitable for audio frequency amplification. Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 58  3.13 DC Load Line and Operating point selection IC RB RC VCE IB VBB VCC Fig 3.17:npn transistor in CE configuration IC (mA) Q-point A 30 μA 20 μA 10 μA IB =0μA B V CE(volts Fig.3.18: output characteristics Consisder a CE amplifier along with the output characteristics as shown in figure 3.18 above. A straight line drawn on the output characteristic of a transistor which gives the various zero signal values (ie. When no signal applied) of VCE and IC is called DC load line. Construction of DC load line Applying KVL to the collector circuit we get, VCC –ICRC –VCE =0-------------------1 VCE = VCC –ICRC ----------------------2 The above equation is the first degree equation and can be represented by a straight line. This straight line is DC load line. To draw the load line we require two end points which can be found as follows. 1. If IC =0, equn 2 becomes VCE = VCC Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 59  2. if VCE = 0, equn 2 becomes VCC = ICRC ie. IC = VCC /RC 3.14 Operating point (Q) A point on the d.c. load line which represent the zero signal values of VCE and IC in a transistor is called as operating point or silent point or quiescent point or Q-point. The Q-point is selected where the DC load line intersects the curve of output characteristics for particular value of zero signal current. i.e. Q-point = (VCE ,IC) Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 60 CHAPTER 4 OPERATIONAL AMPLIFEIR INTRODUCTION Op-Amp (operational amplifier) is basically an amplifier available in the IC form. The word “operational” is used because the amplifier can be used to perform a variety of mathematical operations such as addition, subtraction, integration, differentiation etc. Figure 1 below shows the symbol of an Op-Amp. +VCC V1 Inverting input V2 Noninverting input -VEE Fig.1 Symbol of Op-Amp It has two inputs and one output. The input marked “-“ is known as Inverting input and the input marked “+” is known as Non-inverting input. Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 61  If a voltage Vi is applied at the inverting input ( keeping the non-inverting input at ground) as shown below. Vi VO t t Vi VO Fig.2 Op-amp in inverting mode The output voltage Vo= -AVi is amplified but is out of phase with respect to the input signal by 1800. If a voltage Vi is fed at the non-inverting input ( Keeping the inverting input at ground) as shown below. Vo VO t Vi t Fig.3 Op-Amp in Non-inverting mode Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 62 The output voltage Vo= AVi is amplified and in-phase with the input signal. If two different voltages V1 and V2 are applied to an ideal Op-Amp as shown below. V1 VO V2 Fig.4 Ideal Op-Amp The output voltage will be Vo = A(V1 – V2) i.e the difference of the tow volatages is amplified. Hence an Op-Amp is also called as a High gain differential amplifier. Note: Op-Amp is 8 pin IC ( named as μA 741) with pin details as shown. OFFSET NULL NO CONNECTION 1 8 +VCC INVERTING I/P 2 7 μA 741 OUTPUT NON –INVERTING I/P 3 6 -VEE OFFSET NULL 4 5 Fig. 5 Pin details of Op-Amp Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 63 Block Diagram of an Op-AMP An Op-Amp consists of four blocks cascaded as shown above Fig. 6 Block diagram of an Op-Amp Input stage: It consists of a dual input, balanced output differential amplifier. Its function is to amplify the difference between the two input signals. It provides high differential gain, high input impedance and low output impedance. Intermediate stage: The overall gain requirement of an Op-Amp is very high. Since the input stage alone cannot provide such a high gain. Intermediate stage is used to provide the required additional voltage gain. It consists of another differential amplifier with dual input, and unbalanced ( single ended) output Buffer and Level shifting stage As the Op-Amp amplifies D.C signals also, the small D.C. quiescent voltage level of previous stages may get amplified and get applied as the input to the next stage causing distortion the final output. Hence the level shifting stage is used to bring down the D.C. level to ground potential, when no signal is applied at the input terminals. Buffer is usually an emitter follower used for impedance matching. Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 64 Output stage- It consists of a push-pull complementary amplifier which provides large A.C. output voltage swing and high current sourcing and sinking along with low output impedance. Concept of Virtual ground We know that , an ideal Op-Amp has perfect balance (ie output will be zero when input voltages are equal). Hence when output voltage Vo = 0, we can say that both the input voltages are equal ie V1 = V2. V1 Vo Ri V2 Fig. 7(a) Concept of Virtual ground Since the input impedances of an ideal Op-Amp is infinite ( Ri = ). There is no current flow between the two terminals. Hence when one terminal ( say V2 ) is connected to ground (ie V2 = 0) as shown. VCC V1 =V2 =0 Ri VO V2=0 VEE Fig. 7(b) Concept of Virtual ground Then because of virtual ground V1 will also be zero. Notes by K.R.Sudhindra Ghousia College of Engineering Ramnagar 65 Applications of Op-Amp An Op-Amp can be used as 1. Inverting Amplifer 2. Non-Iverting Amplifer 3. Voltage follower 4. Adder ( Summer) 5. Integrator 6. Differentiator Definitions 1. Slewrate(S): It is defined as “ The rate of change of output voltage per unit time” dVO s= volts / µ sec dt Ideally slew rate should be as high as possible.But its typical value is s=0.5 V/μ-sec. 2. Common Mode Rejection Ratio(CMRR): It is defined as “ The ratio of differential voltage gain to common-mode voltage gain”. Ad CMRR = ACM Ideally CMRR is infinite, but its typical value is CMRR = 90 dB 3. Open Loop Voltage Gain (AV): It is the ration of output voltage to input voltage in the absence of feed back. Its typical value is AV = 2x105 4. Input Impedance (Ri):It is defined as “ The impedance seen by the input(source) applied to one input terminal when the other input terminal is connected to ground. Ri ≈ 2MΩ 5. Output Impedance (RO): It is defined as “ The impedance given by the output (load) for a particular applied input”. Ro ≈