Full Transcript

Module 3: VLANs Instructor Materials Switching, Routing, and Wireless Essentials v7.0 (SRWE) What to Expect in this Module § To facilitate learning, the following features within the GUI may be included in this module: Feature Description Animations Expose...

Module 3: VLANs Instructor Materials Switching, Routing, and Wireless Essentials v7.0 (SRWE) What to Expect in this Module § To facilitate learning, the following features within the GUI may be included in this module: Feature Description Animations Expose learners to new skills and concepts. Expose learners to new skills and concepts. Videos Check Your Per topic online quiz to help learners gauge content understanding. Understanding(CYU) Interactive Activities A variety of formats to help learners gauge content understanding. Small simulations that expose learners to Cisco command line to practice Syntax Checker configuration skills. Simulation and modeling activities designed to explore, acquire, reinforce, and PT Activity expand skills. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 3 What to Expect in this Module (Cont.) § To facilitate learning, the following features may be included in this module: Feature Description Hands-On Labs Labs designed for working with physical equipment. Class Activities These are found on the Instructor Resources page. Class Activities are designed to facilitate learning, class discussion, and collaboration. Self-assessments that integrate concepts and skills learned throughout the Module Quizzes series of topics presented in the module. Module Summary Briefly recaps module content. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 4 Module 3: VLANs Switching, Routing, and Wireless Essentials v7.0 (SRWE) Module Objectives Module Title: Protocols and Models Module Objective: Explain how network protocols enable devices to access local and remote network resources. Topic Title Topic Objective Overview of VLANs Explain the purpose of VLANs in a switched network. VLANs in a Multi-Switched Explain how a switch forwards frames based on VLAN configuration Environment in a multi-switch environment. Configure a switch port to be assigned to a VLAN based on VLAN Configuration requirements. VLAN Trunks Configure a trunk port on a LAN switch. Dynamic Trunking Protocol Configure Dynamic Trunking Protocol (DTP). © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 13 3.1 Overview of VLANs © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 14 Overview of VLANs VLAN Definitions VLANs are logical connections with other similar devices. Placing devices into various VLANs have the following characteristics: Provides segmentation of the various groups of devices on the same switches Provide organization that is more manageable Broadcasts, multicasts and unicasts are isolated in the individual VLAN Each VLAN will have its own unique range of IP addressing Smaller broadcast domains © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 15 Overview of VLANs Benefits of a VLAN Design Benefits of using VLANs are as follows: Benefits Description Smaller Broadcast Dividing the LAN reduces the number of broadcast domains Domains Improved Security Only users in the same VLAN can communicate together Improved IT Efficiency VLANs can group devices with similar requirements, e.g. faculty vs. students Reduced Cost One switch can support multiple groups or VLANs Better Performance Small broadcast domains reduce traffic, improving bandwidth Simpler Management Similar groups will need similar applications and other network resources © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 16 Overview of VLANs Types of VLANs Default VLAN VLAN 1 is the following: The default VLAN The default Native VLAN The default Management VLAN Cannot be deleted or renamed Note: While we cannot delete VLAN1 Cisco will recommend that we assign these default features to other VLANs © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 17 Overview of VLANs Types of VLANs (Cont.) Data VLAN Dedicated to user-generated traffic (email and web traffic). VLAN 1 is the default data VLAN because all interfaces are assigned to this VLAN. Native VLAN This is used for trunk links only. All frames are tagged on an 802.1Q trunk link except for those on the native VLAN. Management VLAN This is used for SSH/Telnet VTY traffic and should not be carried with end user traffic. Typically, the VLAN that is the SVI for the Layer 2 switch. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 18 Overview of VLANs Types of VLANs (Cont.) Voice VLAN A separate VLAN is required because Voice traffic requires: Assured bandwidth High QoS priority Ability to avoid congestion Delay less that 150 ms from source to destination The entire network must be designed to support voice. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 19 Overview of VLANs Packet Tracer – Who Hears the Broadcast? In this Packet Tracer activity, you will do the following: Observe Broadcast Traffic in a VLAN Implementation Complete Review Questions © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 20 3.2 VLANs in a Multi-Switched Environment © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 21 VLANs in a Multi-Switched Environment Defining VLAN Trunks A trunk is a point-to-point link between two network devices. Cisco trunk functions: Allow more than one VLAN Extend the VLAN across the entire network By default, supports all VLANs Supports 802.1Q trunking © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 22 VLANs in a Multi-Switched Environment Networks without VLANs Without VLANs, all devices connected to the switches will receive all unicast, multicast, and broadcast traffic. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 23 VLANs in a Multi-Switched Environment Networks with VLANs With VLANs, unicast, multicast, and broadcast traffic is confined to a VLAN. Without a Layer 3 device to connect the VLANs, devices in different VLANs cannot communicate. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 24 VLANs in a Multi-Switched Environment VLAN Identification with a Tag The IEEE 802.1Q header is 4 Bytes When the tag is created the FCS must be recalculated. When sent to end devices, this tag must be removed and the FCS recalculated back to its original number. 802.1Q VLAN Tag Field Function Type 2-Byte field with hexadecimal 0x8100 This is referred to as Tag Protocol ID (TPID) User Priority 3-bit value that supports Canonical Format Identifier (CFI) 1-bit value that can support token ring frames on Ethernet VLAN ID (VID) 12-bit VLAN identifier that can support up to 4096 VLANs © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 25 VLANs in a Multi-Switched Environment Native VLANs and 802.1Q Tagging 802.1Q trunk basics: Tagging is typically done on all VLANs. The use of a native VLAN was designed for legacy use, like the hub in the example. Unless changed, VLAN1 is the native VLAN. Both ends of a trunk link must be configured with the same native VLAN. Each trunk is configured separately, so it is possible to have a different native VLANs on separate trunks. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 26 VLANs in a Multi-Switched Environment Voice VLAN Tagging The VoIP phone is a three port switch: The switch will use CDP to inform the phone of the Voice VLAN. The phone will tag its own traffic (Voice) and can set Cost of Service (CoS). CoS is QoS for layer 2. The phone may or may not tag frames from the PC. Traffic Tagging Function Voice VLAN tagged with an appropriate Layer 2 class of service (CoS) priority value Access VLAN can also be tagged with a Layer 2 CoS priority value Access VLAN is not tagged (no Layer 2 CoS priority value) © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 27 VLANs in a Multi-Switched Environment Voice VLAN Verification Example The show interfaces fa0/18 switchport command can show us both data and voice VLANs assigned to the interface. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 28 VLANs in a Multi-Switched Environment Packet Tracer – Investigate a VLAN Implementation In this Packet Tracer activity, you will: Part 1: Observe Broadcast Traffic in a VLAN Implementation Part 2: Observe Broadcast Traffic without VLANs © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 29 3.3 VLAN Configuration © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 30 VLAN Configuration VLAN Ranges on Catalyst Switches Catalyst switches 2960 and 3650 support over 4000 VLANs. Normal Range VLAN 1 – 1005 Extended Range VLAN 1006 - 4095 Used in Small to Medium sized businesses Used by Service Providers 1002 – 1005 are reserved for legacy VLANs Are in Running-Config 1, 1002 – 1005 are auto created and cannot Supports fewer VLAN features be deleted Stored in the vlan.dat file in flash Requires VTP configurations VTP can synchronize between switches © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 31 VLAN Configuration VLAN Creation Commands VLAN details are stored in the vlan.dat file. You create VLANs in the global configuration mode. Task IOS Command Enter global configuration mode. Switch# configure terminal Create a VLAN with a valid ID number. Switch(config)# vlan vlan-id Specify a unique name to identify the Switch(config-vlan)# name vlan-name VLAN. Return to the privileged EXEC mode. Switch(config-vlan)# end Enter global configuration mode. Switch# configure terminal © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 32 VLAN Configuration VLAN Creation Example If the Student PC is going to be in VLAN 20, we will create the VLAN first and then name it. If you do not name it, the Cisco IOS will give it a default name of vlan and Prompt Command the four digit number of the VLAN. E.g. S1# Configure terminal vlan0020 for VLAN 20. S1(config)# vlan 20 S1(config-vlan)# name student S1(config-vlan)# end © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 33 VLAN Configuration VLAN Port Assignment Commands Once the VLAN is created, we can then assign it to the correct interfaces. Task Command Enter global configuration mode. Switch# configure terminal Enter interface configuration mode. Switch(config)# interface interface-id Set the port to access mode. Switch(config-if)# switchport mode access Assign the port to a VLAN. Switch(config-if)# switchport access vlan vlan-id Return to the privileged EXEC mode. Switch(config-if)# end © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 34 VLAN Configuration VLAN Port Assignment Example We can assign the VLAN to the port interface. Once the device is assigned the VLAN, then the end device will need the IP address information for that VLAN Prompt Command Here, Student PC receives S1# Configure terminal 172.17.20.22 S1(config)# Interface fa0/18 S1(config-if)# Switchport mode access S1(config-if)# Switchport access vlan 20 S1(config-if)# end © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 35 VLAN Configuration Data and Voice VLANs An access port may only be assigned to one data VLAN. However it may also be assigned to one Voice VLAN for when a phone and an end device are off of the same switchport. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 36 VLAN Configuration Data and Voice VLAN Example We will want to create and name both Voice and Data VLANs. In addition to assigning the data VLAN, we will also assign the Voice VLAN and turn on QoS for the voice traffic to the interface. The newer catalyst switch will automatically create the VLAN, if it does not already exist, when it is assigned to an interface. Note: QoS is beyond the scope of this course. Here we do show the use of the mls qos trust [cos | device cisco-phone | dscp | ip- precedence] command. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 37 VLAN Configuration Verify VLAN Information Use the show vlan command. The complete syntax is: show vlan [brief | id vlan-id | name vlan-name | summary] Task Command Option Display VLAN name, status, and its ports one VLAN per line. brief Display information about the identified VLAN ID number. id vlan-id Display information about the identified VLAN name. The vlan-name name vlan-name is an ASCII string from 1 to 32 characters. Display VLAN summary information. summary © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 38 VLAN Configuration Change VLAN Port Membership There are a number of ways to change VLAN membership: re-enter switchport access vlan vlan-id command use the no switchport access vlan to place interface back in VLAN 1 Use the show vlan brief or the show interface fa0/18 switchport commands to verify the correct VLAN association. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 39 VLAN Configuration Delete VLANs Delete VLANs with the no vlan vlan-id command. Caution: Before deleting a VLAN, reassign all member ports to a different VLAN. Delete all VLANs with the delete flash:vlan.dat or delete vlan.dat commands. Reload the switch when deleting all VLANs. Note: To restore to factory default – unplug all data cables, erase the startup-configuration and delete the vlan.dat file, then reload the device. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 40 VLAN Configuration Packet Tracer – VLAN Configuration In this Packet Tracer activity, you will perform the following: Verify the Default VLAN Configuration Configure VLANs Assign VLANs to Ports © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 41 3.4 VLAN Trunks © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 42 VLAN Trunks Trunk Configuration Commands Configure and verify VLAN trunks. Trunks are layer 2 and carry traffic for all VLANs. Task IOS Command Enter global configuration mode. Switch# configure terminal Enter interface configuration mode. Switch(config)# interface interface-id Set the port to permanent trunking mode. Switch(config-if)# switchport mode trunk Sets the native VLAN to something other Switch(config-if)# switchport trunk native vlan than VLAN 1. vlan-id Specify the list of VLANs to be allowed on Switch(config-if)# switchport trunk allowed the trunk link. vlan vlan-list Return to the privileged EXEC mode. Switch(config-if)# end © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 43 VLAN Trunks Trunk Configuration Example The subnets associated with each VLAN are: VLAN 10 - Faculty/Staff - 172.17.10.0/24 VLAN 20 - Students - 172.17.20.0/24 VLAN 30 - Guests - 172.17.30.0/24 VLAN 99 - Native - 172.17.99.0/24 F0/1 port on S1 is configured as Prompt Command a trunk port. S1(config)# Interface fa0/1 Note: This assumes a 2960 S1(config-if)# Switchport mode trunk switch using 802.1q tagging. S1(config-if)# Switchport trunk native vlan 99 Layer 3 switches require the encapsulation to be configured S1(config-if)# Switchport trunk allowed vlan 10,20,30,99 before the trunk mode. S1(config-if)# end © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 44 VLAN Trunks Verify Trunk Configuration Set the trunk mode and native vlan. Notice sh int fa0/1 switchport command: Is set to trunk administratively Is set as trunk operationally (functioning) Encapsulation is dot1q Native VLAN set to VLAN 99 All VLANs created on the switch will pass traffic on this trunk © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 45 VLAN Trunks Reset the Trunk to the Default State Reset the default trunk settings with the no command. All VLANs allowed to pass traffic Native VLAN = VLAN 1 Verify the default settings with a sh int fa0/1 switchport command. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 46 VLAN Trunks Reset the Trunk to the Default State (Cont.) Reset the trunk to an access mode with the switchport mode access command: Is set to an access interface administratively Is set as an access interface operationally (functioning) © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 47 VLAN Trunks Packet Tracer – Configure Trunks In this Packet Tracer activity, you will perform the following: Verify VLANs Configure Trunks © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 48 VLAN Trunks Lab – Configure VLANs and Trunks In this lab, you will perform the following: Build the Network and Configure Basic Device Settings Create VLANs and Assign Switch Ports Maintain VLAN Port Assignments and the VLAN Database Configure an 802.1Q Trunk between the Switches Delete the VLAN Database © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 49 3.5 Dynamic Trunking Protocol © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 50 Dynamic Trunking Protocol Introduction to DTP Dynamic Trunking Protocol (DTP) is a proprietary Cisco protocol. DTP characteristics are as follows: On by default on Catalyst 2960 and 2950 switches Dynamic-auto is default on the 2960 and 2950 switches May be turned off with the nonegotiate command May be turned back on by setting the interface to dynamic-auto Setting a switch to a static trunk or static access will avoid negotiation issues with the switchport mode trunk or the switchport mode access commands. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 51 Dynamic Trunking Protocol Negotiated Interface Modes The switchport mode command has additional options. Use the switchport nonegotiate interface configuration command to stop DTP negotiation. Option Description Permanent access mode and negotiates to convert the neighboring link access into an access link Will becomes a trunk interface if the neighboring interface is set to trunk dynamic auto or desirable mode Actively seeks to become a trunk by negotiating with other auto or dynamic desirable desirable interfaces Permanent trunking mode and negotiates to convert the neighboring link trunk into a trunk link © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 52 Dynamic Trunking Protocol Results of a DTP Configuration DTP configuration options are as follows: Dynamic Dynamic Auto Trunk Access Desirable Dynamic Auto Access Trunk Trunk Access Dynamic Trunk Trunk Trunk Access Desirable Limited Trunk Trunk Trunk Trunk connectivity Limited Access Access Access Access connectivity © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 53 Dynamic Trunking Protocol Verify DTP Mode The default DTP configuration is dependent on the Cisco IOS version and platform. § Use the show dtp interface command to determine the current DTP mode. § Best practice recommends that the interfaces be set to access or trunk and to turnoff DTP © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 54 Dynamic Trunking Protocol Packet Tracer – Configure DTP In this Packet Tracer activity, you will perform the following: Configure static trunking Configure and verify DTP © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 55 3.6 Module Practice and Quiz © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 56 Module Practice and Quiz Packet Tracer – Implement VLANs and Trunking In this Packet Tracer activity, you will perform the following: Configure VLANs Assign Ports to VLANs Configure Static Trunking Configure Dynamic Trunking © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 57 Module Practice and Quiz Lab – Implement VLANs and Trunking In this lab, you will perform the following: Build the Network and Configure Basic Device Settings Create VLANs and Assign Switch Ports Configure an 802.1Q Trunk between the Switches © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 58 Module Practice and Quiz What did I learn in this module? VLANs are based on logical instead of physical connections. VLANs can segment networks based on function, team, or application. Each VLAN is considered a separate logical network. A trunk is a point-to-point link that carries more than one VLAN. VLAN tag fields include the type, user priority, CFI and VID. A separate voice VLAN is required to support VoIP. Normal range VLAN configurations are stored in the vlan.dat file in flash. An access port can belong to one data VLAN at a time, but may also have a Voice VLAN. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 59 Module Practice and Quiz What did I learn in this module? (Cont.) A trunk is a Layer 2 link between two switches that carries traffic for all VLANs. Trunks will need tagging for the various VLANs, typically 802.1q. IEEE 802.1q tagging makes provision for one native VLAN that will remain untagged. An interface can be set to trunking or nontrunking. Trunk negotiation is managed by the Dynamic Trunking Protocol (DTP). DTP is a Cisco proprietary protocol that manages trunk negotiations. © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 60

Use Quizgecko on...
Browser
Browser