Navigation Introduction PDF

Navigation Principles 1  Enabling Objectives - Know terms associated with the terrestrial coordinate system; Equator, Prime Meridian, Great Circle, Small Circle, Parallel, Meridian, Latitude, Longitude, and Rhumb Line - Understand the concept of Projec...

Navigation Principles 1  Enabling Objectives - Know terms associated with the terrestrial coordinate system; Equator, Prime Meridian, Great Circle, Small Circle, Parallel, Meridian, Latitude, Longitude, and Rhumb Line - Understand the concept of Projections and the main projections used in Navigation - Know the advantages and disadvantages of the Mercator and Gnomonic Projections - Understand the difference between Great Circle Routes and Rhumb Lines - Understand the use of a Nautical Chart and the main concepts associated to nautical charts - Know chart distribution agencies - Understand the function and use of Chart One - Know how to read directions and latitude and longitude on the nautical chart - Know the lengths of a degree of Latitude and Longitude - Understand the use of basic plotting tools 2 Terrestrial Coordinate System Latitude - Equator is the reference for latitude. - Mesures angular distance North or South from the Equator (0º - 090º) - Described in degrees, minutes and seconds followed by the suffix N/S. ᵠ = XXº XX’ XX’’ N/S Degrees expressed always in 2 digits! 3 Terrestrial Coordinate System Longitude - Prime Meridian is the reference for longitude. - Measure the angular distance East or West from the Prime Meridian (0º - 180º). - Described in degrees, minutes and seconds followed by the suffix E/W. λ = XXXº XX’ XX’’ E/W Degrees expressed always in 3 digits! 4  Terrestrial Coordinate System A combination of latitude and longitude is a position on the Earth’s Grid. Example: Riverside Observatory coordinates: - Lat. = 33°57’ 12’’ N - Long. = 117 °23’ 46’’ W Remember: 1 °= 60’ (minutes) 1’ = 60’’ (seconds) 5 Great Circle and Small Circle Great Circle is any circle formed on the surface of Earth by the intersection of a plane passing through the center of the Earth, thereby dividing Earth into two equal parts. Small Circle is any circle formed on the surface of Earth by the intersection of a plane not passing through the center of the Earth. 6  Great Circles - Meridian – Great Circle that is passes through the poles; - Equator – Great Circle that is half-way from the poles; 7  Projections Mercator Projection - Most nautical charts are based on the Mercator Projection. - Rhumb lines, Meridians and Parallels are represented by straight lines. - Meridians and parallels are perpendicular to each other, simplifying plotting positions. 8  Projections Mercator Projection - Advantages: - Lat. and long. appear as a rectangular graticule (easy to plot positions, courses, etc.); - Easy to determine lat./long. of a position plotted; - Easy to measure distance (lat. scale – 1’ = 1NM); and - Easy to locate the four cardinal points. - Disadvantages: - Great-circle distances and directions are not readily determinable; and - High distortion in extreme latitudes. - No representation of the poles. 9  Projections Mercator Projection 10  Nautical Charts - Chart is a graphic representation of a maritime area and adjacent coastal regions. - Charts show: - depths of water and heights of land - natural features of the seabed - details of the coastline - navigational hazards - location of natural and man-made aids to navigation - information on tides and currents - local details of the Earth’s magnetic field (variation) - man-made structures such as bridge and harbours 11  Nautical Charts Distribution Agencies - National Ocean Service (NOS) - Division of National Oceanic & Atmospheric Agency (NOAA) - Coastal US waters, most rivers and Great Lakes for commercial and civilian use - Army Corps of Engineers - Mississippi River (and its tributaries) and some inland lakes - National Geospatial Intelligence Agency(NGA) - formerly NIMA - Department of Defense and International use 12  Nautical Charts Title Block Main information: - Region identification - Main title - Projection and Scale - Publisher - Datum - Depth and elevation notes - Cautionary notes - Tidal information 13  Nautical Charts Datum - Reference point in which measurements are made. - Horizontal Datum: Reference used for distance - Vertical Datum: Reference used for height (sounding) Datum used can be easily found in the Nautical Chart. (datum note) Ex.: ED, NAD 83 14  Nautical Charts Datum - Datum shift: difference between actual and plotted position when using different datum (chart and GPS). ED Datum shift NAD 83 15  Nautical Charts Chart Scale - Ratio of a distance unit on the chart to the actual distance on the surface of the Earth. Ex.: Scale 1:20,000 (one unit of distance on the chart represents 20,000 units on the Earth). Chart Scale is always described in the Title Block. 16  Nautical Charts Chart Scale - Comparing Scales – 1:5,000,000 x 1:5,000 Seems bigger, but is smaller. Remember fractions! - Use the larger scale when near dangers (harbor entrance). - Use the smaller scale when clear from danger (underway at sea). - If in doubt, always use the larger scale! 17 Charts Series General (1:150,001 to Sailing 1:600,000) (1:600,001 and Smaller) Coastal / Approach (1:50,001 to 1:150,000) Harbor (Larger than 1:50,000) Larger scale  smaller area  more details! 18 Nautical Charts Components Compass Rose: - Used to measure directions (true or magnetic) using slider/parallel ruler - Contains the local variation and annual change (increase or decrease). Distance Scale: - Used to measure distances using compass or divider 19  Nautical Charts Chart One - United States of America Nautical Symbols Abbreviations and Terms. 20 Nautical Charts Chart One Chart No. 1 – “Nautical Chart Symbols, Abbreviations and Terms” is a reference publication depicting basic chart elements and explains nautical chart symbols and abbreviations associated with National Ocean Service and NGA charts – A valuable aid for new chart users and a useful tool for all mariners 21 Nautical Charts Chart One 22  Navigation Tools Compass Vs Divider Divider: Used for measuring distances or latitude and longitude. Compass: Used for plotting and measuring distances or latitude and longitude.  Reading Distance - Use compass or divider to select distance then read it on the latitude scale. Some charts have a distance scale which can be easier than using latitude scale. Just place the compass or divider on the distance scale to measure. 24  Plotting Latitude and Longitude Plot: Lat.: 38°56’ 30’’N Long: 076°25’ 30’’ W 1 – Locate the closest intersection of a major meridian/parallel. 2 – Measure the longitude using minute/second scale and plot on Lat.: 38°56’ 30’’N the parallel. Long: 076°26’ 30’’W 3 – Measure the latitude using minute/second scale and plot on the meridian AND from your previous mark. 4 – Using your longitude mark, plot the longitude from the latitude mark. 25  Reading Latitude and Longitude 080°07’00”W 1°= 60’ 1’= 60” Position lat. 25°39’00”N / long 080°07’00”W 25°39’00”N 26  Reading Distance Length of a Degree (Lat. / Long.) - The length of a degree of latitude (measured along a meridian) is the same everywhere on Earth, and equals 60 NM (nautical miles). 1o = 60 NM 1’ = 1 NM - The length of a degree of longitude (measured along a parallel) changes depending on the latitude. 27  Navigation Tools Slider Ruler Scales for reading distances (if it matches the scale of the chart) For reading direction in DEGREES TRUE!  Reading Directions 000o T 270o T 090o T 180o T 29 Reading Directions What is the bearing to the radio tower? Make sure to look at the right 1 – Place your ruler conecting direction: 113oT! your ship to the radio tower (object A to object B). 2 – Slide your ruler to the closest meridian, place the crosshair on the line, and read the bearing. 30 Questions ? 31