Routing Protocol Terminologies
25 Questions
0 Views

Choose a study mode

Play Quiz
Study Flashcards
Spaced Repetition
Chat to Lesson

Podcast

Play an AI-generated podcast conversation about this lesson

Questions and Answers

What does the router do to inform the local router of the bandwidth on the link?

  • Calculates the advertised distance (correct)
  • Assigns the feasible successor
  • Calculates the best backup path
  • Calculates the feasible distance

Which IPv6 address block forwards packets to a multicast address rather than a unicast address?

  • FF00::/12 (correct)
  • 2000::/3
  • FC00::/7
  • FE80::/10

In the context of the exhibit, what happens if the switch port interface trust state becomes untrusted?

  • The switch port remains administratively down
  • Dynamic ARP Inspection is disabled (correct)
  • The switch port remains down until configuration
  • The switch port is connected to another switch

What is the main purpose of PortFast in a spanning tree network?

<p>It minimizes spanning-tree convergence time. (D)</p> Signup and view all the answers

In a scenario where two switches are connected and one is set to Dynamic Auto while the other is set to Dynamic Desirable, what will be the result of this configuration?

<p>The link becomes a trunk port. (B)</p> Signup and view all the answers

What action does B.VTP perform in a network of connected switches?

<p>Propagate VLAN configuration information automatically. (B)</p> Signup and view all the answers

Which mode is necessary to configure an EtherChannel between two switches without using a negotiation protocol?

<p>on (B)</p> Signup and view all the answers

After the Spanning Tree Protocol converges, what action does PortFast take on ports receiving BPDUs?

<p>Shut down the port. (A)</p> Signup and view all the answers

What is the main functionality of a hypervisor in virtual machines?

<p>Virtualizing physical components like CPU and memory (D)</p> Signup and view all the answers

In switch configuration shown in the exhibit, what error needs to be corrected based on the output from switch 1?

<p>Native VLAN mismatch (A)</p> Signup and view all the answers

What OSPF network type is seen on a serial interface running encapsulation PPP by default?

<p>Point-to-point (C)</p> Signup and view all the answers

When PortFast is enabled on an interface connected to another switch, what issue might arise?

<p>Failure to detect switching loops causing broadcast storms (C)</p> Signup and view all the answers

What impact does connecting virtualized servers directly to a separate switch from the hypervisor have on efficiency?

<p>Decreases efficiency by adding unnecessary hops (A)</p> Signup and view all the answers

In an OSPF single area setup between two routers, what network type is typically used for the interface connecting the routers?

<p>Point-to-point (D)</p> Signup and view all the answers

What feature on the Cisco Wireless LAN Controller restricts management access from specific networks?

<p>CPU ACL (B)</p> Signup and view all the answers

What action is taken by a Cisco IP phone when it receives untagged data traffic from an attached PC?

<p>It allows the traffic to pass through unchanged. (C)</p> Signup and view all the answers

What will happen if cable length limits are exceeded?

<p>The network will experience signal degradation. (B)</p> Signup and view all the answers

Which of the following does virtualization NOT involve?

<p>Allowing logical network devices to communicate only within their virtual environment. (D)</p> Signup and view all the answers

What is the purpose of TACACS in a Cisco environment?

<p>User authentication and authorization. (D)</p> Signup and view all the answers

What is the correct IPv4 network and subnet mask combination to assign in order to minimize 10.10.2250/28?

<p>10.10.225.32, 255.255.255.224 (A)</p> Signup and view all the answers

Which configuration correctly allows Router R1 to send all traffic to 192.168.1.1 when there is no matching routing-table entry?

<p>R1(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.1 (C)</p> Signup and view all the answers

What command should be configured on the Switched Virtual Interface to efficiently use address space in an office with 8 floors and 30-40 users per floor?

<p>ip address 192.168.0.0 255.255.254.0 (D)</p> Signup and view all the answers

In the provided exhibit, which switch is designated as the root bridge?

<p>S2 (C)</p> Signup and view all the answers

What action can establish an OSPF neighbor relationship without forming an adjacency?

<p>Modify hello interval (D)</p> Signup and view all the answers

Which IPv4 network and subnet mask combination should be assigned to minimize 10.10.225 18/28?

<p>10 10 225 32, 255 255 255 224 (B)</p> Signup and view all the answers

More Like This

Routing Protocols
10 questions

Routing Protocols

TriumphalMorganite avatar
TriumphalMorganite
Routing Protocols and Autonomous Systems Quiz
15 questions
Use Quizgecko on...
Browser
Browser