Lesson 2

Play an AI-generated podcast conversation about this lesson

What is the aim of Lesson 2 on handling the rifle?

To demonstrate how to strip and assemble magazines

To teach the cadet how to carry out function tests

To instruct the cadet on stripping and assembling the weapon for daily maintenance (correct)

To provide basic indoor or outdoor lessons on rifle handling

How many magazines are required per cadet/CFAV according to the handling instructions?

4

1

2 (correct)

3

What preparation step is mentioned in the handling instructions?

Placing maintenance kits under the chairs with combination tools ready to use (correct)

Ensuring that only the correct tools are used for stripping and assembling

Imposing a time limit during the practice stage of stripping and assembling

Making sure that components are laid out in a random sequence

What is the method suggested for teaching stripping and assembling in Lesson 2?

Teaching in a sequence devised to ensure that parts are stripped with damage Signup and view all the answers

How many 40-minute periods are suggested for covering Lesson 2?

Two Signup and view all the answers

What should be done with the parts during stripping and assembling, according to the handling instructions?

Lay out components in the sequence of stripping on a clean, dry surface Signup and view all the answers

What is NOT imposed during the practice stage of stripping and assembling?

NO time limit imposed during the practice stage Signup and view all the answers

'Only' which tools should be used to prevent damage to parts during stripping and assembling?

$20 correct tools Signup and view all the answers

'Rifle fitted with iron sight and sling' is stored at what ratio per cadet/CFAV?

1 per cadet/CFAV Signup and view all the answers

'To avoid possible damage to the rifle, NO time limit is imposed' when?

During practice stage of stripping and assembling Signup and view all the answers

What should be done to ensure the rifle is functioning correctly after stripping and assembling?

Release the trigger with the safety catch set to Fire (F) Signup and view all the answers

How should magazines be stripped if they have been exposed to conditions likely to produce a build-up of mud, sand, or rust?

Hold the magazine with the bottom plate uppermost and depress the base of the spring located in the center of the bottom plate Signup and view all the answers

What is the consequence of failing to correctly engage the bottom plate of a magazine?

The magazine will become unserviceable Signup and view all the answers

What is the purpose of stripping magazines?

To clean and maintain the magazine Signup and view all the answers

What must be done if the spring comes loose from the platform during magazine stripping?

Reinsert the spring correctly into the platform Signup and view all the answers

When should magazines be stripped according to the procedure?

If they have been exposed to conditions likely to produce a build-up of mud, sand, or rust Signup and view all the answers

Which action confirms that a magazine has been correctly engaged after stripping?

Pressing the spring until it engages in its slot in the body Signup and view all the answers

What does setting the safety catch to Safe (S) ensure during rifle function testing?

The rifle will not fire when attempting to operate the trigger Signup and view all the answers

What is recommended if any defects are identified during a rifle function test?

Report them immediately to a CFAV or an Armourer Signup and view all the answers

What is emphasized about stripping rifles in Lesson Conclusion?

Stripping rifles beyond what is taught is dangerous and can cause damage to the weapon Signup and view all the answers

What is the correct procedure for checking the barrel to ensure it is not fouled?

Hold it up towards the light about 150mm away from the head, muzzle pointing towards the eye, keeping both eyes open and following the lands and grooves throughout their length. Signup and view all the answers

Who is authorized to strip and assemble the bolt carrier assembly?

Only CFAVs Signup and view all the answers

What is the sequence of stripping laid down in order to prevent damage to the weapon components?

STWD - Sights, Trigger mechanism, Weapon, Dust cover Signup and view all the answers

What must be done if any defects are noticed during inspection of the weapon?

Report it to a CFAV who will report the fault to the Armourer Signup and view all the answers

What is the correct way to remove the Trigger Mechanism Housing (TMH) from the rifle?

Gently withdraw the rear TMH locking pin first, then withdraw the front TMH locking pin. Separate the TMH from the body by pulling the butt upwards. Signup and view all the answers

What should be done if the TMH locking pins come completely out?

Report this fact to a CFAV Signup and view all the answers

What is the purpose of conducting a rifle function test after stripping and assembling?

To ensure that all parts are reassembled correctly Signup and view all the answers

What should be done if any defects are identified during the function test?

Report defects to a CFAV or an Armourer immediately Signup and view all the answers

When stripping the gas system, what should you do to remove the gas plug?

Depress the plunger on the front of the plug and withdraw it backwards through the gas block without rotating it Signup and view all the answers

What is the purpose of ensuring that the bolt and firing pin that were stripped are placed back into the same weapon?

To avoid interchangeability of bolts and firing pins Signup and view all the answers

When removing the handguard, what should be done before sliding it over the muzzle?

Unscrew the front sling loop keeper screw and remove the front sling loop Signup and view all the answers

What is the recommended way to ensure that the barrel is clear from any obstructions?

Hold it up towards a light source about 150mm away from the head, keeping both eyes open and follow the lands and grooves throughout their length Signup and view all the answers

What should be done after aligning the recoil rods and spring with the holes in the back of the carrier when assembling?

Push in the TMH rear locking pin to engage the end of the assembly Signup and view all the answers

What should be ensured before replacing the cocking handle through the side of the body when assembling?

The bolt is fully forward in the carrier Signup and view all the answers

What should be done if the TMH locking pins come completely out?

Report the fact to an Armourer Signup and view all the answers

Who is authorized to strip and assemble the bolt carrier assembly?

CFAVs only Signup and view all the answers

What should be done if any defects are identified during a rifle function test?

Report the defects to an Armourer immediately Signup and view all the answers

What is the purpose of ensuring that the barrel is not fouled before reassembling the rifle?

To ensure the rifle functions correctly Signup and view all the answers

When should magazines be stripped according to the procedure?

Daily Signup and view all the answers

What must be done if the spring comes loose from the platform during magazine stripping?

Report the issue to an Armourer Signup and view all the answers

'Only' which tools should be used to prevent damage to parts during stripping and assembling?

CFAV-approved tools Signup and view all the answers

What should be done after aligning the recoil rods and spring with the holes in the back of the carrier when assembling?

Replace the cocking handle through the side of the body Signup and view all the answers

What should be felt/heard when the rifle is cocked and the trigger is operated after setting the safety catch to Fire (F)?

The hammer engaging the main sear Signup and view all the answers

What should be done if the spring comes loose from the platform during magazine stripping?

Ensure that the spring is fitted correctly Signup and view all the answers

What should be ensured before replacing the cocking handle through the side of the body when assembling?

The barrel is clear from any obstructions Signup and view all the answers

What is recommended if any defects are identified during a rifle function test?

Report defects to a CFAV or an Armourer immediately Signup and view all the answers

When should magazines be stripped according to the procedure?

If they have been exposed to conditions likely to produce a build-up of mud, sand, or rust Signup and view all the answers

What is the purpose of stripping magazines?

To clean and maintain the magazine components Signup and view all the answers

What should be done if any defects are noticed during inspection of the weapon?

Report defects to a CFAV or an Armourer immediately Signup and view all the answers

'Only' which tools should be used to prevent damage to parts during stripping and assembling?

'Combination' tools Signup and view all the answers

What method is suggested for teaching stripping and assembling in Lesson 2?

Indoor or outdoor lesson with basic equipment Signup and view all the answers

What should be done if the spring comes loose from the platform during magazine stripping?

Stop and reattach the spring securely Signup and view all the answers

What must be done if any defects are noticed during inspection of the weapon?

Report and rectify the defects before assembly Signup and view all the answers

What is the purpose of ensuring that the bolt and firing pin that were stripped are placed back into the same weapon?

To maintain consistency in weapon assembly Signup and view all the answers

What should be done after aligning the recoil rods and spring with the holes in the back of the carrier when assembling?

Securely attach the carrier to the rifle body Signup and view all the answers

What is emphasized about stripping rifles in Lesson Conclusion?

The importance of maintaining cleanliness of parts Signup and view all the answers

What is recommended if any defects are identified during a rifle function test?

Report and rectify the defects before further use Signup and view all the answers

What should be done with the parts during stripping and assembling, according to the handling instructions?

'Parts are to be laid out with the TMH locking pins uppermost' Signup and view all the answers

'Rifle fitted with iron sight and sling' is stored at what ratio per cadet/CFAV?

'1 per cadet/CFAV' Signup and view all the answers

How many magazines are required per cadet/CFAV according to the handling instructions?

2 per cadet/CFAV Signup and view all the answers

When removing the Bolt Carrier Assembly, what should be done to ensure proper reassembly?

Ensure that the same bolt is placed back into the same weapon. Signup and view all the answers

What should be done to strip the Gas System according to the handling instructions?

Depress the plunger on the front of the gas plug and withdraw it through the gas block without rotating it. Signup and view all the answers

What is emphasized about stripping rifles in Lesson Conclusion?

To ensure that bolts and firing pins are NOT interchanged during stripping. Signup and view all the answers

What must be done if any defects are identified during inspection of the weapon?

Rectify any defects before conducting a rifle function test. Signup and view all the answers

What should be done after aligning the recoil rods and spring with the holes in the back of the carrier when assembling?

Push in the TMH rear locking pin to engage the end of the assembly. Signup and view all the answers

What is recommended if any defects are identified during a rifle function test?

Rectify any defects before conducting a rifle function test. Signup and view all the answers

Lesson 2

Choose a study mode

Podcast

Questions and Answers

What is the aim of Lesson 2 on handling the rifle?

How many magazines are required per cadet/CFAV according to the handling instructions?

What preparation step is mentioned in the handling instructions?

What is the method suggested for teaching stripping and assembling in Lesson 2?

How many 40-minute periods are suggested for covering Lesson 2?

What should be done with the parts during stripping and assembling, according to the handling instructions?

What is NOT imposed during the practice stage of stripping and assembling?

'Only' which tools should be used to prevent damage to parts during stripping and assembling?

'Rifle fitted with iron sight and sling' is stored at what ratio per cadet/CFAV?

'To avoid possible damage to the rifle, NO time limit is imposed' when?

What should be done to ensure the rifle is functioning correctly after stripping and assembling?

How should magazines be stripped if they have been exposed to conditions likely to produce a build-up of mud, sand, or rust?

What is the consequence of failing to correctly engage the bottom plate of a magazine?

What is the purpose of stripping magazines?

What must be done if the spring comes loose from the platform during magazine stripping?

When should magazines be stripped according to the procedure?

Which action confirms that a magazine has been correctly engaged after stripping?

What does setting the safety catch to Safe (S) ensure during rifle function testing?

What is recommended if any defects are identified during a rifle function test?

What is emphasized about stripping rifles in Lesson Conclusion?

What is the correct procedure for checking the barrel to ensure it is not fouled?

Who is authorized to strip and assemble the bolt carrier assembly?

What is the sequence of stripping laid down in order to prevent damage to the weapon components?

What must be done if any defects are noticed during inspection of the weapon?

What is the correct way to remove the Trigger Mechanism Housing (TMH) from the rifle?

What should be done if the TMH locking pins come completely out?

What is the purpose of conducting a rifle function test after stripping and assembling?

What should be done if any defects are identified during the function test?

When stripping the gas system, what should you do to remove the gas plug?

What is the purpose of ensuring that the bolt and firing pin that were stripped are placed back into the same weapon?

When removing the handguard, what should be done before sliding it over the muzzle?

What is the recommended way to ensure that the barrel is clear from any obstructions?

What should be done after aligning the recoil rods and spring with the holes in the back of the carrier when assembling?

What should be ensured before replacing the cocking handle through the side of the body when assembling?

What should be done if the TMH locking pins come completely out?

Who is authorized to strip and assemble the bolt carrier assembly?

What should be done if any defects are identified during a rifle function test?

What is the purpose of ensuring that the barrel is not fouled before reassembling the rifle?

When should magazines be stripped according to the procedure?

What must be done if the spring comes loose from the platform during magazine stripping?

'Only' which tools should be used to prevent damage to parts during stripping and assembling?

What should be done after aligning the recoil rods and spring with the holes in the back of the carrier when assembling?

What should be felt/heard when the rifle is cocked and the trigger is operated after setting the safety catch to Fire (F)?

What should be done if the spring comes loose from the platform during magazine stripping?

What should be ensured before replacing the cocking handle through the side of the body when assembling?

What is recommended if any defects are identified during a rifle function test?

When should magazines be stripped according to the procedure?

What is the purpose of stripping magazines?

What should be done if any defects are noticed during inspection of the weapon?

'Only' which tools should be used to prevent damage to parts during stripping and assembling?

What method is suggested for teaching stripping and assembling in Lesson 2?

What should be done if the spring comes loose from the platform during magazine stripping?

What must be done if any defects are noticed during inspection of the weapon?

What is the purpose of ensuring that the bolt and firing pin that were stripped are placed back into the same weapon?

What should be done after aligning the recoil rods and spring with the holes in the back of the carrier when assembling?

What is emphasized about stripping rifles in Lesson Conclusion?

What is recommended if any defects are identified during a rifle function test?

What should be done with the parts during stripping and assembling, according to the handling instructions?

'Rifle fitted with iron sight and sling' is stored at what ratio per cadet/CFAV?

How many magazines are required per cadet/CFAV according to the handling instructions?

When removing the Bolt Carrier Assembly, what should be done to ensure proper reassembly?

What should be done to strip the Gas System according to the handling instructions?

What is emphasized about stripping rifles in Lesson Conclusion?

What must be done if any defects are identified during inspection of the weapon?

What should be done after aligning the recoil rods and spring with the holes in the back of the carrier when assembling?

What is recommended if any defects are identified during a rifle function test?

More Like This

Lesson 3

Lesson 6

Lesson 7

Lesson 9