Supplement 213-09
34 Questions
1 Views

Choose a study mode

Play Quiz
Study Flashcards
Spaced Repetition
Chat to lesson

Podcast

Play an AI-generated podcast conversation about this lesson

Questions and Answers

Which of the following is the primary role of the Cutters Edge saw in the Philadelphia Fire Department?

  • To minimize the development of super-heated, oxygen-deficient, and fuel-rich environments
  • To speed tactical operations by accomplishing ventilation early and effectively
  • To cut and remove building components such as wood and roofing materials (correct)
  • To establish a safer interior environment through planned and systematic removal of heat, smoke, and toxic gases

    • What is the fuel mixture for the Cutters Edge saw's 2-cycle motor?

  • 100:1 gasoline/ oil mixture
  • 75:1 gasoline/ oil mixture
  • 50:1 gasoline/ oil mixture (correct)
  • 25:1 gasoline/ oil mixture

    • What is the purpose of ventilation in firefighting?

  • To speed tactical operations by accomplishing ventilation early and effectively
  • To minimize the development of super-heated, oxygen-deficient, and fuel-rich environments
  • To cut and remove building components such as wood and roofing materials
  • To establish a safer interior environment through planned and systematic removal of heat, smoke, and toxic gases (correct)

    • Which of the following is NOT recommended for cleaning the filter element?

    <p>Water</p> Signup and view all the answers

    What should be done after removing the carburetor compartment cover?

    <p>Clean the cooling fins on the cylinder and flywheel</p> Signup and view all the answers

    What is the purpose of the tension adjustment screw on the clutch cover?

    <p>To remove slack during installation</p> Signup and view all the answers

    What can happen if the chain is installed too loose when it heats up during use?

    <p>The chain will throw off the saw</p> Signup and view all the answers

    Which of the following is true about cleaning the Cutters Edge Saw?

    <p>The bar should be flipped every time the chain is replaced</p> Signup and view all the answers

    What should be done to ensure proper lubrication of the chain?

    <p>Clean the oil channel and make sure the pump tube is attached to the motor housing</p> Signup and view all the answers

    What should be done prior to placing the saw back on the apparatus?

    <p>Check the gas and bar oil levels and top off fluids as needed</p> Signup and view all the answers

    What should be done if the guide bar is immersed in a solvent tank?

    <p>Purge the nose sprocket bearing of solvent</p> Signup and view all the answers

    Which part of the Cutters Edge Saw is designed to protect the operator from the chain and allows the depth of cut to be set?

    <p>Tool-less Guard/Depth® Gauge</p> Signup and view all the answers

    What is the purpose of the Top Ported Muffler in the Cutters Edge Saw?

    <p>To move the heat and smoke away from the saw and operator</p> Signup and view all the answers

    What is the purpose of the Compression Release in the Cutters Edge Saw?

    <p>To reduce starting resistance by 40% for easier starts</p> Signup and view all the answers

    What is the purpose of the Full-Wrap Handle in the Cutters Edge Saw?

    <p>To assure safe operation of the saw in any position and act as a chain catch</p> Signup and view all the answers

    Which of the following is NOT a recommended practice for maintaining a chainsaw?

    <p>Starting the saw and immediately jumping on the throttle</p> Signup and view all the answers

    What is the purpose of the Tool-less Guard/Depth Gauge in a chainsaw?

    <p>All of the above</p> Signup and view all the answers

    What is the purpose of the Top Ported Muffler in a chainsaw?

    <p>To reduce noise and direct exhaust gases away from the operator</p> Signup and view all the answers

    Which of the following is NOT a type of kickback that the fire service typically encounters?

    <p>Diagonal</p> Signup and view all the answers

    What is the purpose of the chain brake in the Cutters Edge Saw?

    <p>To engage the brake and stop the chain</p> Signup and view all the answers

    When should the chain be replaced in the Cutters Edge Saw?

    <p>When the guide bar is in good condition</p> Signup and view all the answers

    What can happen if the chain tension is improper in the Cutters Edge Saw?

    <p>Excess chain vibration and housing failure</p> Signup and view all the answers

    Which of the following is a safety procedure when operating a rotary saw?

    <p>Cut on horizontal surfaces near ground level</p> Signup and view all the answers

    What should be done when starting a flooded chainsaw?

    <p>Push the choke handle all the way in</p> Signup and view all the answers

    What is the purpose of the decompression button when starting a Partner rotary saw?

    <p>To reduce the pressure in the cylinder for an easier start</p> Signup and view all the answers

    What should be done after starting the Partner rotary saw?

    <p>Allow the engine to settle down to idle</p> Signup and view all the answers

    Which of the following is a sign that the belt on the Cutters Edge saw is slipping?

    <p>The engine revs up quickly and the blade does not</p> Signup and view all the answers

    What should be done to adjust the belt tension on the Cutters Edge saw?

    <p>Loosen 2 bolts and use a flat screwdriver to screw the adjusting bolt in to add tension</p> Signup and view all the answers

    How can you tell if the blade guard on the Cutters Edge saw is stuck?

    <p>It does not move freely with just hand pressure</p> Signup and view all the answers

    In which position is the blade on the Cutters Edge saw best suited for forcible entry?

    <p>Outboard</p> Signup and view all the answers

    Which of the following is an indication that the engine is flooded?

    <p>All of the above</p> Signup and view all the answers

    What should be done to clear a flooded engine?

    <p>Push in the choke and pull the starter cord</p> Signup and view all the answers

    What can cause the saw to run rough?

    <p>All of the above</p> Signup and view all the answers

    What can a clogged muffler cause in the saw?

    <p>All of the above</p> Signup and view all the answers

    More Like This

    Directive 61 EMS Certifications Quiz
    10 questions

    Directive 61 EMS Certifications Quiz

    DextrousAlexandrite avatar
    DextrousAlexandrite
    SAFETY - PERSONAL GROOMING 13
    20 questions

    SAFETY - PERSONAL GROOMING 13

    DextrousAlexandrite avatar
    DextrousAlexandrite
    UNIFORMS 19A (1)
    20 questions

    UNIFORMS 19A (1)

    DextrousAlexandrite avatar
    DextrousAlexandrite
    EQUAL EMPLOYMENT COMPLAINT PROCEDURES 58
    20 questions

    EQUAL EMPLOYMENT COMPLAINT PROCEDURES 58

    DextrousAlexandrite avatar
    DextrousAlexandrite
    Use Quizgecko on...
    Browser
    Open
    Browser
    Browser