Combustion Appliance Zone (CAZ) Testing PDF

Document Details

EndearingDesert

Uploaded by EndearingDesert

null

Tags

combustion appliance home appliances combustion safety building codes

Summary

This document provides a comprehensive guide for combustion appliance zone (CAZ) testing. It covers various aspects, including scope, description, configurations of zones, and tests to maintain combustion safety with relevant codes and standards, including NFPA 54.

Full Transcript

EERE (https://www.energy.gov/eere/office-energy-efficiency-renewable-ene rgy) » BTO (https://www.energy.gov/eere/buildings/building-technologies-o ffice) » Building America (https://www.energy.gov/eere/building-america) » Solution Center Home (https://basc.pnnl.gov/) » Guides A-Z (https://bas c.pnnl...

EERE (https://www.energy.gov/eere/office-energy-efficiency-renewable-ene rgy) » BTO (https://www.energy.gov/eere/buildings/building-technologies-o ffice) » Building America (https://www.energy.gov/eere/building-america) » Solution Center Home (https://basc.pnnl.gov/) » Guides A-Z (https://bas c.pnnl.gov/resource-guides) » Combustion Appliance Zone (CAZ) Testing Combustion Appliance Zone (CAZ) Testing Scope If the home contains natural-draft appliances (such as a natural-draft furnace, boiler, or water heater) then combustion safety testing must be conducted by a certified Combustion safety testing using a smoke pen energy rater (as required by the NFPA 54 (https://basc.p nnl.gov/library/list-nfpa-codes-standards)). See the Compliance Tab (https://basc.pnnl.gov/resource-guides/comb ustion-appliance-zone-caz-testing#edit-group-compliance) for related codes and standards requirements, and criteria to meet national programs such as DOE’s Zero Energy Ready Home program (https://ba sc.pnnl.gov/library/doe-zero-energy-ready-home-national-program-req uirements-rev-07), ENERGY STAR Single-Family New Homes (https://ba sc.pnnl.gov/library/energy-star-residential-new-construction-program -requirements), and Indoor airPLUS (https://basc.pnnl.gov/library/epaindoor-airplus-construction-specifications-version-1-rev-04). Description If a home's furnace, boiler, and/or water heater is installed within the home’s pressure boundary (i.e., within the thermal envelope), this equipment should be direct-vent/sealed-combustion equipment. (See the Building America Solution Center guides Direct Vent Equipment (h ttps://basc.pnnl.gov/resource-guides/direct-vent-equipment#quickta bs-guides=1)and Combustion Furnaces (https://basc.pnnl.gov/resourc e-guides/combustion-furnaces#quicktabs-guides=1) for more information.) ENERGY STAR permits non-direct-vented combustion appliances in Climate Zones 1, 2, and 3 (https://basc.pnnl.gov/sites/default/f iles/images/IECCmap_Revised.jpg). If non-direct vented appliances (also known as atmospheric-vented or Category 1 appliances) are installed in a confined space or an air-tight building, two fresh air supply ducts or openings must be installed to provide combustion air in the combustion appliance zone (CAZ) as described below and as required by NFPA 54, Sections 5.3.3 and 5.3.4 (https://basc.pnnl.gov/library/nfpa -54-national-fuel-gas-code). Providing the correct amount of combustion and dilution air for Category I furnaces, boilers, and water heaters is paramount for safe and efficient operation. Combustion dilution air should come from outdoors but it is also legal for combustion air to come from the CAZ, provided there is enough air volume in the CAZ. The National Fuel Gas Code (https://basc.pnnl.gov/library/list-nfpa-co des-standards) describes several methods for providing combustion air to the CAZ; these are shown in Figures 1 through 5. Configurations of Combustion Appliance Zones Appliances should be installed in a zone or room that can be sealed from the indoor space and communicated to the outdoors through openings in the wall or ducts that connect to the outdoors. This room could include: A mechanical closet that opens or vents to the outdoors. A separate room open to the outdoors. Note that basements and crawl spaces are not good spaces for zone isolation. If a basement or crawl space must be used as the location for an atmospherically vented combustion appliance, to ensure proper zone isolation, follow these steps: Ensure that there are no cracks, gaps, or openings in the physical boundary of the zone so that it is completely air-tight relative to the living space. Make sure that duct or furnace cabinets located in the zone are sealed to prevent air leakage and to avoid the movement of air from the zone to the living space. In retrofit situations, if an atmospheric combustion appliance will be installed in a basement or crawlspace, remove all exhaust devices (e.g. exhaust fans, fireplaces, clothes dryers) or provide additional makeup air to adequately serve all of the exhaust devices in the zone. Option 1. Combustion air vertical ducts through floor and ceiling Combustion air can be drawn through vertical ducts in the floor and ceiling (see Figure 1) with one duct through the floor to the vented crawlspace and one duct through the ceiling to the vented attic. The duct into the attic terminates above the attic insulation. The interior openings should be within 12 inches of the ceiling and within 12 inches of the floor. The minimum net free area of each opening should be one square inch per 4,000 Btu/h of the total input of all the appliances in the zone. Be sure to account for louvers, screens, or grilles. Figure 1. Combustion air is provided to the CAZ from outside through vertical ducts in the floor and ceiling. (Source: Calcs Plus (https://basc.pnnl.gov/library/calcs-plu s).) Option 2. Combustion air vertical ducts through attic to vented ceiling – Figure 2 shows two vertical ducts through the ceiling to the vented attic. One hole is located in the ceiling with the duct terminating above the insulation. The second duct extends from a point within 12 inches of the floor and extending up through the ceiling and terminating above the insulation in the attic. The minimum net free area of each opening should be one square inch per 4,000 Btu/h of the total input of all the appliances in the zone. The same duct opening calculation is used for Figure 2 as for Figure 1. Be sure to account for louvers, screens, or grilles. Figure 2. Combustion air is provided to the CAZ from outside through vertical ducts in the ceiling. (Source: Calcs Plus (https://basc.pnnl.gov/library/calcs-plus).) Option 3. Combustion air horizontal ducts through exterior wall – With this option shown in Figure 3, both openings are through an exterior wall, with one opening near the top of the wall and one near the bottom of the wall and total input BTU/h is divided by 2,000 BTU/h. Be sure to account for louvers, screens or grilles. Figure 3. Combustion air is provided to the CAZ from outside through horizontal ducts in the exterior wall. Option 4. Single duct through exterior wall – When a single combustion inlet is used in an exterior wall as shown in Figure 4, the opening should be within 12 inches of the top of the zone. The minimum net free area of the opening should be one square inch per 3,000 Btu/h of the total input of all the appliances and not less than the sum of all the vent connectors in the space. Figure 4. Combustion air is provided to the CAZ from outside through a horizontal duct in the outside wall. (Source: Calcs Plus (https://basc.pnnl.gov/library/calcs-plu s).) For any of these options, the openings must be a minimum of 3 inches in width or height. If the opening is covered with a grille or louver, you must compensate for the area covered by the grille. Use the manufacturer’s labeled free area when provided or, if unlabeled, assume that wood grilles or louvers have 25% free area and that metal grilles or louvers have 75% free area and increase the size of the opening to meet the minimum calculated free area required (NFPA 54, Section 9.3.7). Option 5. Combustion air horizontal ducts through interior wall (not recommended) – Although this option is not recommended, this situation may be encountered in some older homes or retrofit projects. If this method is used, it is strongly recommended that the contractor refer to a document titled “Measure Guideline: Combustion Safety for Natural Draft Appliances Using Indoor Air (https://basc.pnnl. gov/library/measure-guideline-combustion-safety-natural-draft-appli ances-using-indoor-air).” Combustion dilution air can also be taken from the main building volume or CAZ, if adequate room volume exists, not counting rooms with closable doors. Figure 5. Combustion air is provided to the CAZ from inside through horizontal ducts in the inside wall. (Source: Calcs Plus (https://basc.pnnl.gov/library/calcs-plus).) The formula to calculate the required room volume for combustion dilution air is: (the total input BTU/H of all Category I appliances in the CAZ) X (0.05) For example, the CAZ in Figure 11 has a Category I, 60,000-BTUH input furnace and a 30,000-BTUH input gas water heater (also Category I), which give a net of 90,000 BTUH input, so at 50 cubic feet per 1,000 BTU/h (50/1000) this gives a multiplier of .05: 0.05 x 90,000 BTUH = 4,500 ft3 Thus the equipment requires either the CAZ to be 4,500 ft3 or for the furnace to be connected to 4,500 ft3 of building space. This would be a space about 20 ft wide by 28.125 ft long by 8 ft tall. The building volume should not include bedrooms, bathrooms, laundry rooms, or any room with a door closing it off from the main volume. If connecting the CAZ to building space through an interior wall, two openings or ducts should be located in the wall, one duct within 12 inches of the ceiling and the second duct within 12 inches of the floor. The area of each duct opening in square inches is calculated as the total input BTUH divided by 1,000 BTUH for each duct. If the opening is covered with a grille or louver, you must compensate for the area covered by the grille. Assume that wood grilles or louvers have 25% free area and that metal grilles or louvers have 75% free area and increase the size of the opening to meet the minimum calculated free area required (NFPA 54, Section 9.3.7). How to Test the Combustion Appliance Zone If outdoor air is used to provide combustion air to the appliances, there are two test conditions for the combustion appliance assessment: equipment-off and equipment-on. With the equipment off, verify that the CO level in the zone is below the alarm limit and that there is no natural gas leakage. Also verify that the vent system installation is compliant with the –NFGC, Chapter 12 for installation and Chapter 13 for sizing. As mentioned above, verify that the combustion air openings are free of blockage and meet the code requirement for net free area. Finally, inspect the appliance for visual signs of deterioration and clean or repair as needed. For the equipment-on test, turn on the equipment and perform the following checks (note that exhaust fan testing does not apply to the zone isolation case): 1. Check for successful ignition and functioning controls. 2. Check that the appliance drafts correctly using a smoke pen or other device. 3. Check appliance input for over-firing: clock meter or measure the size of the orifice and pressure. 4. Measure the CO level in the flue and determine that the value is not above the ANSI certification limit for that type of appliance (Table 1). 5. Check safety and protective devices: pilot shut off, high temp limit, low water cutout, and temperature pressure relief. Although this method is not recommended, if indoor air is used to provide combustion air to the appliances, follow the steps below for the combustion appliance assessment: 1. Close all exterior doors, windows, and fireplace dampers. Open all interior doors. Leave open all combustion air openings to the outdoors. 2. If there is a central air handler and a bedroom or separate room without a ducted return grille, close the door(s) to those rooms. 3. Turn on any clothes dryers. Turn on any exhaust fans, such as range hoods and bathroom exhausts, so they will operate at maximum speed. Do not operate a summer (whole-house) exhaust fan. Close fireplace dampers. 4. Place the appliance being inspected in operation. Follow the lighting instructions, if required. Adjust the thermostat so the appliance will operate continuously. 5. Measure the CO level in the flue and determine that the value is not above the ANSI certification limit for that type of appliance (Table 1). 6. Test for spillage at the draft hood relief opening after 5 minutes of main burner operation. Use the flame of a match or candle or smoke. 7. Turn on all other fuel-gas-burning appliances within the same room so they will operate at their full inputs. Follow lighting instructions for each appliance. Circulating air blowers (if any) should be operating. 8. Repeat step 6, above, on the appliance being inspected. 9. If another appliance is to be inspected, shut off all appliances and return to Step 1. 10. Return doors, windows, exhaust fans, fireplace dampers, and any other fuel-gas-burning appliance to their previous conditions of use. Table 1. CO Thresholds. If any combustion appliance fails the spillage test with other equipment on but passes under natural conditions with other equipment off, the cause and potential improvement is most likely with the availability of combustion air, not with the performance of the vent system. Combustion air openings to the outdoors or some other remediation may be required. If the combustion appliance fails the spillage or combustion tests under natural conditions (all exhaust fans off), a service technician should be called before proceeding. Ensuring Success When furnaces, boilers, and water heaters are installed within the home’s pressure boundary (i.e., within the thermal envelope), this equipment should be direct-vent/sealed-combustion equipment. ENERGY STAR permits non-direct-vented combustion appliances in Climate Zones 1, 2, and 3 (https://basc.pnnl.gov/sites/default/files/images/I ECCmap_Revised.jpg) if the Rater has followed Section 805 of RESNET’s Standards, encompassing ANSI/ACCA 12 QH-2014, Appendix A, Sections A3 (Carbon Monoxide Test) and A4 (Depressurization Test for the Combustion Appliance Zone), and verified that the equipment meets the limits defined within. Climate No climate-specific information applies. Right and Wrong Images Compliance The Compliance tab contains both program and code information. Code language is excerpted and summarized below. For exact code language, refer to the applicable code, which may require purchase from the publisher. While we continually update our database, links may have changed since posting. Please contact our webmaster (mailt o:[email protected]) if you find broken links. ENERGY STAR Single-Family New Homes, Version 3/3.1 (Rev. 11) (http s://basc.pnnl.gov/library/energy-star-residential-new-construction -program-requirements) National Rater Field Checklist HVAC System. 10. Combustion Appliances. 10.1 Furnaces, boilers, & water heaters are mechanically drafted or direct-vented. Alternatives in Footnote 66. 64, 65, 66 10.2 Fireplaces are mechanically drafted or direct-vented. Alternatives in Footnote 67. 64, 65, 67 10.3 If unvented combustion appliances other than cooking ranges or ovens are located inside the home’s pressure boundary, the Rater has followed ANSI/ACCA 12 QH-2014, Section 3.2.2, Appendix A Sections A2.2.6, A3, and A4, and verified the equipment meets the limits defined within. 64, 68 Footnote 64) The pressure boundary is the primary enclosure boundary separating indoor and outdoor air. For example, a volume that has more leakage to outside than to conditioned space would be outside the pressure boundary. Footnote 65) Per the 2009 International Mechanical Code, a direct-vent appliance is one that is constructed and installed so that all air for combustion is derived from the outdoor atmosphere and all flue gases are discharged to the outside atmosphere; a mechanical draft system is a venting system designed to remove flue or vent gases by mechanical means consisting of an induced draft portion under nonpositive static pressure or a forced draft portion under positive static pressure; and a natural draft system is a venting system designed to remove flue or vent gases under nonpositive static vent pressure entirely by natural draft. Footnote 66) This item only applies to furnaces, boilers, and water heaters located within the home’s pressure boundary. Naturally drafted equipment is allowed within the home’s pressure boundary in Climate Zones 1-3 if the Rater has followed ANSI / ACCA 12 QH-2014, Section 3.2.2, Appendix A Sections A2.2.6, A3 (Carbon Monoxide Test), A4 (Depressurization Test for the Combustion Appliance Zone), and verified that the equipment meets the limits defined within. Footnote 67) This item only applies to fireplaces located within the home’s pressure boundary. Naturally drafted fireplaces are allowed within the home’s pressure boundary if the Rater has verified that the total net rated exhaust flow of the two largest exhaust fans (excluding summer cooling fans) is ≤ 15 CFM per 100 sq. ft. of occupiable space when at full capacity. If the net exhaust flow exceeds the allowable limit, it shall be reduced or compensating outdoor airflow provided. Per ASHRAE 62.2-2010, the term “net rated exhaust flow” is defined as flow through an exhaust fan minus the compensating outdoor airflow through any supply fan that is interlocked to the exhaust fan. Per ASHRAE 62.2-2010, the term “occupiable space” is defined as any enclosed space inside the pressure boundary and intended for human activities, including, but not limited to, all habitable spaces, toilets, closets, halls, storage and utility areas, and laundry areas. See Footnote 51 for the definition of “habitable spaces”. Footnote 68) The minimum volume of combustion air required for safe operation by the manufacturer and / or code shall be met or exceeded. Also, in accordance with the National Fuel Gas Code, ANSI Z223.l / NFPA54, unvented room heaters shall not be installed in bathrooms or bedrooms. Please see the ENERGY STAR Single-Family New Homes Implementation Timeline (https://basc.pnnl.gov/library/energy-star-re sidential-new-construction-program-requirements) for the program version and revision currently applicable in your state. DOE Zero Energy Ready Home (Revision 07) (https://basc.pnnl.gov/li brary/doe-zero-energy-ready-home-national-program-requirements-re v-07) Exhibit 1 Mandatory Requirements. Exhibit 1, Item 1) Certified under the ENERGY STAR Qualified Homes Program or the ENERGY STAR Multifamily New Construction Program. Exhibit 1, Item 6) Certified under EPA Indoor airPLUS. EPA Indoor airPLUS (Revision 04) (https://basc.pnnl.gov/library/ep a-indoor-airplus-construction-specifications-version-1-rev-04) 5.1 Combustion Equipment Located in Conditioned Spaces. Item 5.1 requires that builders meet certain requirements for fuel-burning and space-heating appliances that are located in conditioned space. Completion of the ENERGY STAR checklists (which is a DOE Zero Energy Ready Home requirement) now satisfies the following Indoor airPLUS requirements: Mechanically draft or direct vent all gas- and oil-fired furnaces, boilers and water heaters located in conditioned spaces. Naturally drafted equipment is allowed in Climate Zones 1-3 if the Rater has followed the combustion safety test procedures in Section 805 of the RESNET Standard. Fireplaces that are not mechanically drafted or direct-vented to the outdoors must meet maximum allowed exhaust flow Ensure that all fireplaces and other fuel-burning and spaceheating appliances located in conditioned spaces are vented to the outdoors and supplied with adequate combustion and ventilation air according to the manufacturers' installation instructions. National Fuel Gas Code (NFPA-5 2012) (https://basc.pnnl.gov/librar y/list-nfpa-codes-standards) The products of combustion from a gas-fired furnace (noncondensing) are vented out of the building using specific types of vent pipes made up of different materials depending on the flue gas temperatures, as specified in ANSI Z223.1, the National Fuel Gas Code (NFPA-5 2012), "Table 12.5.1 Type of Venting System to Be Used." 2009 (https://basc.pnnl.gov/library/2009-irc-international-residen tial-code-one-and-two-family-dwellings), 2012 (https://basc.pnnl.g ov/library/2012-irc-international-residential-code-one-and-two-fa mily-dwellings), 2015 (https://basc.pnnl.gov/library/2015-irc-intern ational-residential-code-one-and-two-family-dwellings), 2018 (http s://basc.pnnl.gov/library/2018-irc-international-residential-code-o ne-and-two-family-dwellings), and 2021 International Residential Code (IRC) (https://basc.pnnl.gov/library/2021-international-reside ntial-code) Chapter 14 Heating and Cooling equipment covers general requirements, installation, clearances, and location. Chapter 24 Fuel Gas is extracted from the International Fuel Gas Code with modifications and covers gas piping systems, appliances, venting systems, and combustion air configurations. Retrofit: 2009 (https://basc.pnnl.gov/library/2009-irc-international-re sidential-code-one-and-two-family-dwellings), 2012 (https://basc.pnn l.gov/library/2012-irc-international-residential-code-one-and-two-fami ly-dwellings), 2015 (https://basc.pnnl.gov/library/2015-irc-internationa l-residential-code-one-and-two-family-dwellings), 2018, (https://basc. pnnl.gov/library/2018-irc-international-residential-code-one-and-two-f amily-dwellings) and 2021 (https://basc.pnnl.gov/library/2021-interna tional-residential-code) IRC Section R102.7.1 Additions, alterations, or repairs. Additions, alterations, renovations, or repairs shall conform to the provisions of this code, without requiring the unaltered portions of the existing building to comply with the requirements of this code, unless otherwise stated. (See code for additional requirements and exceptions.) Appendix J regulates the repair, renovation, alteration, and reconstruction of existing buildings and is intended to encourage their continued safe use. 2009 (https://basc.pnnl.gov/library/2009-international-mechanic al-code), 2012 (https://basc.pnnl.gov/library/2012-international-m echanical-code), 2015 (https://basc.pnnl.gov/library/2015-internati onal-mechanical-code), 2018 (https://basc.pnnl.gov/library/2018-i nternational-mechanical-code), and 2021 International Mechanical Code (IMC) (https://basc.pnnl.gov/library/2021-international-mech anical-code) Comply with all relevant sections. Note, Chapter 2 - Definitions defines categories of combustion appliances based on venting type. When conducting renovation work in older homes, identify any combustion appliances located in the home (e.g., gas or oil-fired water heater, boiler, or furnace) and determine whether they are sealed combustion/direct vent appliances or older-model atmospheric-draft or induced-draft combustion appliances (also known as Category 1 appliances based on their designation in the National Fuel Gas Code; see the guide Direct Vent Equipment (https://basc.pnnl.gov/resourceguides/direct-vent-equipment#quicktabs-guides=1)for an explanation of these categories). Any renovation work that will involve air sealing and insulating rooms, attics, basements, or crawlspaces that may contain category 1 appliances will impact how much air is available to the appliance for combustion. As part of the renovation, calculate the combustion air that will be available to the appliances and perform combustion appliance zone testing, as described in the Description tab (https://basc.pnnl.gov/resource-guides/combustion-appliance-zo ne-caz-testing#edit-group-description), to help ensure that adequate amounts of makeup air will be available for safe combustion. If the home currently has atmospheric-draft or induced-draft combustion appliances, the best course of action is to replace them with more efficient and safer-direct vent combustion appliances or other noncombustion equipment. For more information on combustion appliances, please see the assessment guide, Pre-Retrofit Assessment of Combustion Appliances (https://basc.pnnl.gov/information/pre-retrofit-assessment-combusti on-appliances). The U.S. Department of Energy’s Standard Work Specifications (http s://basc.pnnl.gov/library/standard-work-specifications) has additional information on combustion appliances. See Compliance (https://basc.pnnl.gov/resource-guides/combustionappliance-zone-caz-testing#edit-group-compliance) tab. More Info. Access to some references may require purchase from the publisher. While we continually update our database, links may have changed since posting. Please contact our webmaster (mailto:[email protected]) if you find broken links. Case Studies Technology Solutions Case Study: Combustion Safety for Appliances Using Indoor Air  Author(s): Gas Technology Institute, University of Minnesota Organization(s): NSTAR, PARR, NorthernSTAR Publication Date: May, 2014 Case study describing a method for evaluating safe installation and operation of combustion appliances in homes undergoing energy efficiency upgrades where indoor air is used for combustion and venting. References and Resources* 2009 IMC - International Mechanical Code (https://co des.iccsafe.org/public/document/details/toc/750) Author(s): International Code Council Organization(s): ICC Publication Date: January, 2009 2009 edition of code establishing minimum regulations for mechanical systems, including heating, cooling, ventilation, exhaust, ducts, fireplaces, combustion and hydronic systems, using prescriptive and performance-related provisions. Building America Best Practices Series Volume 14: HVAC: A Guide for Contractors to Share with Homeowners  Author(s): Gilbride Theresa L, Baechler Michael C, Hefty Marye G, Hand James R, Love Pat M Organization(s): Pacific Northwest National Laboratory, PNNL, Oak Ridge National Laboratory, ORNL Publication Date: August, 2011 Report providing information about energy-efficient heating, ventilation, and cooling (HVAC) equipment options to help homeowners cut their energy use, reduce their carbon footprint, and increase their homes comfort, health, and safety. Measure Guideline: Combustion Safety for Natural Draft Appliances Through Appliance Zone Isolation  Author(s): Fitzgerald J, Bohac D Organization(s): Center for Energy and Environment, CEE, NorthernSTAR Building America Partnership, NorthernSTAR, University of Minnesota Publication Date: April, 2014 Measure Guideline describing how to assess and carry out the isolation of natural draft combustion appliances from the conditioned spaces of low-rise residential buildings. Measure Guideline: Combustion Safety for Natural Draft Appliances Using Indoor Air  Author(s): Brand Larry Organization(s): Partnership for Advanced Residential Retrofit, PARR, Gas Technology Institute, GTI Energy Publication Date: May, 2014 This measure guideline provides guidance on combustion safety inspection procedures for appliances and heating equipment that use indoor air for combustion and dilution of flue gases in low-rise residential buildings. NFPA 54/ANSI Z223.1: National Fuel Gas Code (https:// catalog.nfpa.org/NFPA-54-National-Fuel-Gas-Code-C26 6.aspx) Author(s): National Fire Protection Association Organization(s): National Fire Protection Association Publication Date: January, 2018 Code providing minimum safety requirements for the design and installation of fuel gas piping systems in homes and other buildings. Technician’s Guide & Work Book For Quality Installation (https://www.acca.org/store#/productDet ail/1802d500-bc20-e511-80fc-fc15b4283f74/) Author(s): Air Conditioning Contractors of America Organization(s): ACCA Publication Date: January, 2010 The Technician's Guide equips practitioners with the knowledge to properly implement all of the measurement procedures required in the HVAC QI Specification. National Program Requirements ENERGY STAR Certified Homes (Version 3/3.1, Rev. 9)  Author(s): U.S. Environmental Protection Agency Organization(s): EPA Publication Date: September, 2018 Webpage with links to documents providing the program requirements and checklists for ENERGY STAR Certified Homes (Ver. 3/3.1, Rev. 9). Calcs Plus (http://www.calcs-plus.com/) Author(s): Calcs Plus Organization(s): Calcs Plus A professional heating and air conditioning design company, specializing in both residential and light commercial work. Measure Guideline: Combustion Safety for Natural Draft Appliances Using Indoor Air  Author(s): Brand Larry Organization(s): Partnership for Advanced Residential Retrofit, PARR, Gas Technology Institute, GTI Energy Publication Date: May, 2014 This measure guideline provides guidance on combustion safety inspection procedures for appliances and heating equipment that use indoor air for combustion and dilution of flue gases in low-rise residential buildings. *For non-dated media, such as websites, the date listed is the date accessed. Contributors to this Guide The following authors and organizations contributed to the content in this Guide. Calcs-Plus (http://www.calcs-plus.com/) Pacific Northwest National Laboratory (http://www.pnnl.gov/) Combustion Appliance Zone (CAZ) Test = TECHNICAL DESCRIPTION Combustion safety tests are an important part of a performance Alternate Terms ■ Advanced check-up or a maintenance call Combustion for homes with combustion Safety appliances that rely on gravity Diagnostics draft exhaust. This includes furnaces and water heaters that burn gas, propane, or oil and have open flues with a risk of combustion gas spillage when other fans are operating in the home (e.g., kitchen and bathroom fans or clothes dryers). This test helps diagnose whether these appliances are operating safely by checking if there is adequate air for all the combustion appliances present, making sure the appliances are safely exhausting emissions up the flue or chimney, and verifying that no emissions are pulled back into the home even if all of the exhaust fans in the home were operating at the same time. Sales Message Last Updated: 2017-07-24 Mobile Field Kit The Building America Field Kit allows you to save items to your profile for review or use on-site. Sign Up (https://basc.pnnl.gov/user/register) Log In (https://basc.pnnl.gov/user) or

Use Quizgecko on...
Browser
Browser